Table of Contents
Advertisement
Available languages
Available languages
English
Telescoping Handle (Fig. A, E)
This pressure washer has a convenient, built in telescoping
handle and transport wheels.
1. To unlock the telescoping handle
release button
13
and slide the handle upwards. You will
hear an auidible click when it snaps into position.
2. To store the telescoping handle
release button
13
and slide the telescoping handle
down and into the pressure washer body. You will hear an
auidible click when it snaps into position.
3. To move the pressure washer
transport wheels
15
unit by the telescoping handle.
Accessory Storage Compartment (Fig. F)
This pressure washer has a built in accessory storage
compartment
34
to carry the spray wand, spray handle,
handle grip and turbo nozzle.
1. To unlock the storage door
latch
11
counterclockwise and flip the door open
to access the spray wand
grip
5
, and turbo nozzle
2. To lock the storage door
closed position. Rotate the door latch
the storage door into position.
Assembling Spray Wand (Fig. G)
1. To connect the spray handle
insert the threaded end of the spray handle onto the
threaded end of the handle grip. Rotate the spray handle
clockwise until fully tightened.
2. To connect the spray wand
the threaded end of the spray wand into the threaded
collar
40
of the spray handle. Rotate the threaded
collar
40
clockwise until fully tightened.
High Pressure and Suction Hose Storage
(Fig. I)
This pressure washer has a built in storage area to carry the
high pressure hose. The coiled hose is secured between the
hose storage brace
31
and the pressure washer unit
1. To access the high pressure hose
hose
27
, unlock the hose storage latch
swing the hose storage brace
pressure washer unit
2. Unwrap the hose storage strap
from the pressure washer unit
3. Swing the hose storage brace
the hose storage latch
brace
31
to the pressure washer unit
Attaching High Pressure Hose (Fig. I)
CAUTION: NEVER PULL WATER SUPPLY HOSE TO
MOVE pressure washer. This could damage hose and/
or pump inlet.
nOTE: Uncoil the high pressure hose
prevent kinks.
12
12
, press the handle
12
, press the handle
8
, tilt the unit so the
are touching the ground and pull the
10
, rotate the door
2
, spray handle
4
22
.
10
, place the storage door in the
11
clockwise to lock
4
to the handle grip
2
to the spray handle
1
or the suction
32
and
31
away from the
8
.
33
and remove the hose
8
.
31
closed and lock
32
securing the hose storage
8
.
1
before installation to
nOTE: Avoid cross threading when installing the hose. Cross
threading will cause leaks.
1. To connect the high pressure hose
grip
5
coupler
2. To connect the high pressure hose to the pressure
washer unit
pressure water outlet
Attaching Garden Hose (Fig. J)
nOTE: Before connecting the garden hose to the pressure
washer unit, run water through the garden hose for thirty
seconds to clear any debris from inside the garden hose.
1. To connect a garden hose to the
pressure washer unit
garden hose
2. Securely tighten the garden hose by hand.
nOTE: Always disconnect the garden hose after usage.
Attaching Nozzles (Fig. K)
DANGER: Risk of fluid injection. Do not direct
, handle
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury will occur.
WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while
pressure washer is running. Turn pressure washer unit
OFF before changing nozzles.
1. To connect a nozzle to the spray wand
5
,
connect collar
appropriate nozzle.
4
2. Release the quick connect collar to lock the nozzle in place.
4
, insert
3. Give the nozzle a firm tug after the quick connect collar
has locked into place to ensure the nozzle is locked
into place.
nOTE: The nozzles listed below might not be included with your
pressure washer but are available for purchase at an additional cost.
Common Spray Nozzles
15 ° Orange Nozzle
25 ° Green Nozzle
8
.
40 ° White Nozzle
Black Turbo Nozzle
To Attach the Suction Hose (Fig. L)
Use the suction hose to pull water from a bucket or other
fresh water source.
NOTICE: Do not use to suction soap, chemicals, dirty
or corrosive liquids, such as window cleaner, plant food,
fertilizers or bleach. Do not use with salt water.
nOTE: Avoid cross threading when installing the hose. Cross
threading will cause leaks.
1. To connect the suction hose
pressure washer unit
collar
, thread the hose collar
37
31
.
8
, thread the hose collar
18
.
8
, place the end of the
38
inside the water intake
3
toward the spray wand and insert the
Common Applications
For brick or masonry.
For vinyl siding.
For automotive washing.
For abrasive cleaning.
27
8
, thread the suction hose
30
onto the water intake
1
to the handle
onto the inlet
36
onto the high
17
.
2
, pull the quick
to the
17
.
Advertisement
Table of Contents
