Huawei HoloSens Quick Start Manual page 4

Device Installation/ 设备安装
E. Waterproofing and Insulation/ 防水绝缘处理
NOTE/ 说明
• Before that, check the cabling and ensure that the camera runs properly to avoid reworkings.
做绝缘防水处理前请检查线缆是否接好并可正常工作，避免二次返工。
• The waterproof tape must cover the cable bundle from the insulation sheath all the way to the cable conduit (for
example, a PVC tube). The tape must be wrapped tightly and there must be no gaps in the coverage or water
will leak in.
防水胶带务必从线缆束绝缘外皮开始缠绕至防护皮管（如 PVC 管），且尽量缠紧，且覆盖到位，以免漏水。
•If a corrugated pipe is installed, a drainage hole should be deployed at the lowest point of the pipe to prevent
water from getting into the pipe. Long-term soaking may cause pigtail damage.
若安装波纹管，请在波纹管的最低点做排水孔处理，避免波纹管内积水，导致摄像机尾线长期浸泡导致损坏。
1
Wrap one layer of insulation tape around each
cable joint.
用绝缘胶带缠绕每条线缆对接处，缠绕一层。
Insulation tape
绝缘胶带
Use the insulation tape to protect the waterproof
3
tape layer. Then, use cable ties to secure the both
ends.
再用绝缘胶带缠绕一层。 最后用扎线带绑扎上下两端。
Insulation tape
绝缘胶带
Cable tie
扎线带
2
Stretch the waterproof tape evenly to twice its original
length. Then apply one layer of waterproof tape.
均匀拉伸防水胶带，使其长度为原来的 2 倍，再缠绕一层。
Waterproof tape
防水胶带
Cover the rest of the cabling in a conduit or with
4
protective waterproof rubber tape. Make a drip loop
as shown below to create an artificial lowest point of
the cable.
使用防护皮管或者防水胶带，包住线缆其他部分，并制作
滴水弯。滴水弯呈倒 Ω 型，形成线缆的最低点。
Drip loop
滴水弯
Installation Verification/ 安装后检查
Verifying the Installation/ 安装后检查
After the device installation, check the following items to ensure that the device is properly installed.
设备安装完成后，请确认如下事项，以保证设备安装正确。
Check Items/ 检查项
All screws are fully tightened.
确认所有螺钉已经完全拧紧，以接合处不能偏移为准。
The camera is securely installed on the mount or wall.
确认摄像机与支架或者墙壁等之间的安装是稳固可靠的。
The ambient temperature meets the device specifications.
确认工作的环境温度满足设备规格。
Insulation and waterproof measures have been taken to protect cables installed in humid
environment, and the drip loops are in correct positions.
设备安装在潮湿环境时，确认网线以及尾线已经做好绝缘防水处理，滴水弯位置正确。
If the camera has a ground cable, ensure that the camera is ground. If it is powered by a PoE
switch, ensure that the PoE switch is also grounded.
对于有接地线的摄像机，确认摄像机已接地，如果是 PoE 交换机供电，则 PoE 交换机也已接地。
The protective film and fixing rubber strip have been removed from the lens and camera body
respectively.
对于有镜头 / 视窗保护膜或机身固定胶条的摄像机，确认已撕掉摄像机镜头保护膜和机身固定胶条。
The camera can power on properly.
确认设备能够正常上电运行。
You can access the camera web client using the IP address you configured.
确认能够使用配置好的 IP 地址登录设备 Web 页面。
On the camera web client, you can view live video from the camera.
确认能够通过 Web 页面浏览实况。
If the camera is a smart one, ensure that the captured target or vehicle image is clear. The
recommended target resolution is at least 120 x 120 pixels. The recommended horizontal
resolution of a license plate is at least 80 pixels.
如果是智能款型摄像机，请确保抓拍到的目标 / 车辆图片清晰，推荐目标大小为 120*120 像素及以上，
车牌水平大小为 80 像素及以上。
In night vision mode, the detection area can be viewed clearly.
确认夜视情况下，能够看清楚检测区域。
4
Result/ 检查结果
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
Yes/ 是□ No/ 否□
You can view the detection scene on the web page.
1
通过 Web 页面查看，被检测区域在镜头检测范围内。
The delivered images are clear.
2
检测画面图像清晰。