Download Print this page
Sharp PN-ZS701 Operation Manual
Sharp PN-ZS701 Operation Manual

Sharp PN-ZS701 Operation Manual

Trolley stand

Advertisement

Quick Links

TIPS
The supplied clamps can be attached to the stand rods and shelf board
bar to hold the cables.
Specifications
Model
PN-ZS701
Height
4 positions
adjustment
Center height of the screen
Approx. 1310 mm (51-9/16 inch) [A],
approx. 1210 mm (47-5/8 inch) [B],
approx. 1110 mm (43-11/16 inch) [C],
approx. 1010 mm (39-3/4 inch) [D]
(Depends on the position of the mounting
brackets attached in Step 1-(4).)
Dimensions
See the diagram at right
Weight
Approx. 48 kg (105.8 lbs.)
As a part of our policy of continuous improvement, SHARP
reserves the right to make design and specification changes
for product improvement without prior notice. The
performance specification figures indicated are nominal
values of production units.
There may be some deviations from these values in individual
units.
Back
Clamp position
Clamp
Units: mm (inch)
(Note that the values shown are approximate values.)
1980 (77-15/16)
Printed in China
TINSE1212MPZZ(1)
– 4 –
Operation Manual
TROLLEY STAND PN-ZS701
Applicable models (as of September 2011)
(Available models differ according to region.)
● Thank you for purchasing a SHARP product.
Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the section "To
ensure safe and correct use". After reading the manual, keep it in a convenient location where it can be accessed at any time.
TIPS
- This product was shipped after strict quality control and inspection; however, if breakage or a malfunction should be found,
contact your SHARP dealer or your nearest customer contact.
- Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a
third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is
recognized under law.
- This product and its accessories may be upgraded without advance notice.
This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels
and incorrectly using the product could have results as classified below.
Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all
instructions.
Warning:
Not following these instructions could result
in death or serious injury.
• The installation must be performed by qualified service
personnel.
Improper installation work may cause the monitor to fall or
topple over, resulting in injury.
• Do not place the stand on an unstable surface.
Do not subject to intense shock or vibration.
Toppling or falling may occur, causing injury.
• Only use this product with specified models. Do not
modify the stand or the accessories.
Otherwise, the monitor may fall or the stand may topple
over, resulting in injury.
• Lock the casters when using the stand.
Toppling may occur, causing injury.
• Do not transport the stand with a monitor attached.
If the monitor mounting attachments become broken or
damaged, the monitor may fall or the stand may break or
topple, resulting in injury.
• Use the supplied screws. Tighten all screws firmly.
Insufficient tightening may cause the monitor to fall or the
stand to topple over, resulting in injury.
Get other manuals https://www.bkmanuals.com
LCD MONITOR PN-L702B
To ensure safe and correct use
Caution:
• Do not climb onto or lean on the stand and monitor.
Toppling may occur, causing injury.
• If deformation or cracks are discovered, stop using the
stand.
Using the stand without repairing the problem may cause
the monitor to fall or the stand to topple, resulting in injury.
• Take suitable preventative measures to reduce the risk
of this product falling or toppling due to an earthquake
or other circumstances.
The equipment for preventing falling and toppling will not
be effective if the wall or table to which the equipment is
attached is not sufficiently strong. Reinforce the wall or
table sufficiently. These measures to prevent falling and
toppling are intended to reduce the risk of injury and other
harm, however, their effectiveness is not guaranteed in all
earthquakes.
– 1 –
Not following these instructions could result
in injury or property damage.

Advertisement

loading

Summary of Contents for Sharp PN-ZS701

  • Page 1 (Depends on the position of the mounting contact your SHARP dealer or your nearest customer contact. brackets attached in Step 1-(4).) - Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a Dimensions See the diagram at right...
  • Page 2 Spring washers washers * Hang the bar so that the side with screw Installation procedure (for SHARP dealers and service engineers) holes faces upward. Caster (5) Provisionally attach the upper mounting Caution bar to the left and right stand rods with the screws (M6x14) (x6).