Sealey MK77 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
Ensure the dispenser is on a reasonably flat, level floor before loading.
9
Ensure that all fittings are tight and secure.
9
DO NOT use the dispenser for any purpose other than that for which it is designed.
8
2. INTRODUCTION
Single roll dispenser accepts 900mm rolls and can be used either horizontally or vertically. Durable lightweight design with wheels for easy
manoeuvrability.
3. SPECIFICATION
Roll size: ...................................................900mm (roll width)
Max Capacity: .............................................20kg (roll weight)
4. CONTENTS
1 . .............MK77.01 .............................. Side Frame (R/H) x1
2 . .............MK77.02 ................................ Side Frame (L/H) x1
3 . .............MK77.03 ................................................... Base x1
4 . .............SS845.S .... Hex Head Set Screw M8 X 45 Zinc x9
5 . .............MK77.05 ........................................... Cross Bar x1
6 . .............MK77.06 ......................................... Wheel Axle x1
7 . ........... FWM12.S .........................Flat Washer M12 Zinc x4
8 . .............MK77.08 ........................................Fixed Wheel x2
9 . .............MK77.09 .............................................Snap Pin x2
10 . ...........MK77.10 ........................................... Brake Bar x2
11 ................SN8.S ............................... Steel Nut M8 Zinc x5
12 . ...........MK77.12 ................................................. Spring x1
13 . ...........MK77.13 ................................... Rubber Spacer x1
14 . ...........SS850.S .... Hex Head Set Screw M8 X 50 Zinc x1
15 . ........... FWM8.S ...........................Flat Washer M8 Zinc x1
16 . ...........MK77.16 ........................................... Tape Reel x1
17 . ...........MK77.17 .............................................. Bushing x1
18 . ........... FWM8.S ...........................Flat Washer M8 Zinc x1
19 . ...........MK77.19 .......................................... Pivot Tube x1
20 . ........ HHB870.S ................. Hex Head Bolt M8 x 70mm x1
5. ASSEMBLY
(Refer to parts diagram overleaf)
NOTE: Before assembling, note the location of the "brake bar" (10) mounting holes in the base (3) in relation to the "cross bar" (5) and
spring (12) mounting holes in the side frames (1,2).
5.1. Attach side frames (1,2) to base (3) with two M8 x 45 mm hex bolts (4). DO NOT tighten bolts.
5.2. Attach front "cross bar" (5) to lower set of holes in side frames with two M8 x 45 mm hex bolts (4). Tighten all bolts in base.
5.3.
Slide "wheel axle" (6) through base and place two M12 flat washers on each end of the "wheel axle" (6).
5.4. Slide "fixed wheels" (8) on each end of the wheel axle.
5.5.
Install the two "brake bars" (10) to base with M8 x 45 mm (4) as shown on the parts diagram.
5.6. Hook the springs (12), with the rubber spacer (13), into holes on each side frame.
5.7. Install the "tape reel" (16) to inside of both side frames as shown on the parts diagram.
6. MAINTENANCE
6.1. If in constant use, check the tightness of all fixings on a weekly basis.
© Jack Sealey Limited
POLYMASK/MASKING PAPER DISPENSER 1 X
900MM ROLL
MK77
MODEL NO:
Original Language Version MK77 Issue 2 (2) 30/09/20