Sealey MK65.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
1. SAFETY
Ensure the dispenser is on a reasonably flat, level floor or wall mounted securely before loading.
9
Ensure that all fittings are tight and secure.
9
Be aware that the paper cutting blades are sharp, handle with care.
9
DO NOT use the dispenser for any purpose other than that for which it is designed.
8
DO NOT sit or stand on the dispenser.
8
2. INTRODUCTION
Single roll dispenser accepts rolls up to 450mm and can be used floor standing or wall mounted. Automatically applies adhesive tape
to edges of masking paper.
3. CONTENTS
See fig.3 overleaf.
Number Description
1 Tubular Frame
2 Top Handle
3 Cutting Blade
4 Cross tube
5 Paper holding springs
6 Paper holding washers
7 Paper holding Rings
8 Paper Bar
9 Mounting bracket
10 Cutting blade spring
4. ASSEMBLY
NOTE: Numbers in brackets refer to item numbers in fig.3.
4.1. If dispenser is to be free standing fit the four rubber feet to the tubular frames (1).
4.2. If the dispenser is to be bench or wall mounted fit the two mounting brackets (9) to the rear legs of the tubular
frames (1), using M16 screws (15), M6 washers (14) and M6 nuts (13). Fit two of the feet to the front legs of the tubular frames (1).
4.3. Attach the top handle (2) to the top of the tubular frames (1) using M8 screws (12) and M8 washers (11).
4.4. Attach the two tubular frames (1) to the cross tube (4) using M8 screws (12) and M8 washers (11). DO NOT fully tighten screws at this
stage.
4.5. Fit cutting blade spring (10) to either end of the cutting blade (3), as shown in fig.1.
4.6. Fit cutting blade (3) to upper holes in front legs of tubular frames (1) using M16 screws (15), M6 washers (14) and M6 nuts (13).
4.7. Tighten all screws/nuts.
4.8. Insert bolts (18) through front legs of tubular frames (1) and tighten in place using M6 washers (14)
and M6 nuts (13).
4.9. Thread a wing nut (17) onto each bolt (18) with the wings towards the frame leg.
4.10. Slide washer (14) and hub (20) onto each bolt (18) and then fit tape reels (19) onto hubs (20) with open sides towards tubular
4.11. frame (1) legs.
4.12. Position tape reels (19) with washer (14) and wing nut (17).
4.13. Fit paper washers (6), cutting blade spring (10) and paper holding spring (5) to paper bar (8) as shown in fig.2.
4.14. Locate paper bar (8) between bars of tubular frames (1) and retain with knob (16).
© Jack Sealey Limited
MASKING PAPER DISPENSER 450MM ROLL
MK65.V3
MODEL NO:
Quantity
Number
2
11
1
12
1
13
1
14
2
15
4
16
4
17
1
18
2
19
1
20
Original Language Version
Description Quantity
Washers (M8) 4
Screws (M8) 4
Nuts (M6) 6
Washers (M6) 16
Screws (M16) 8
Knobs 2
Wing nuts 4
Long bolts 2
Tape Reel 2
Hub 2
fig.1
fig.2
MK65.V3 Issue1 08/11/23