Transistors Q101 in PCB drive the laser diodes. When Q101 is shorted between their terminals, the laser diodes will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam. DEH-2350UB/XNES...
Page 3
CAUTION Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacture. Discord used batteries according to the manufacture's instructions. DEH-2350UB/XNES...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DEH-2350UB/XNES...
10.1 TUNER AMP UNIT (GUIDE PAGE) ......................38 10.2 KEYBOARD UNIT ..........................44 10.3 CD CORE UNIT (S11.1STD-DOUT) ......................46 10.4 WAVEFORMS............................48 11. PCB CONNECTION DIAGRAM ........................50 11.1 TUNER AMP UNIT ..........................50 11.2 KEYBOARD UNIT ..........................54 11.3 CD CORE UNIT (S11.1STD-DOUT) ......................56 12. ELECTRICAL PARTS LIST ...........................58 DEH-2350UB/XNES...
If the lead is bent, please correct the angle between the lead and the light receiving part to be 90 degrees or replace the infrared deteching unit for remote control (GP1UXC14RK). DEH-2350UB/XNES...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. DEH-2350UB/XNES...
WMA decoding format ..Ver. 7, 7.1, 8, 9, 10, 11, 12 Specifications and the design are subject to mod- (2ch audio) (Windows Media Player) ifications without notice. MP3 decoding format ...MPEG-1 & 2 Audio Layer 3 WAV signal format ....Linear PCM & MS ADPCM (Non-compressed) 2.2 DISC/CONTENT FORMAT DEH-2350UB/XNES...
USB port Detach button B (BAND/ESC) CAUTION Indicator State Use an optional Pioneer USB cable (CD-U50E) to connect the USB audio player/USB mem- Tuner: band and frequency Main dis- Program service name ory as any device connected directly to the...
3 Right 5 Rear speaker or subwoofer 4 Front speaker Fastening the front panel If you do not plan to detach the front panel, the front panel can be fastened with the supplied screw. Screw ES, ES1 : XXX7020 DEH-2350UB/XNES...
See the table below for the items to be checked regarding audio: Item to be checked regarding audio Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted DEH-2350UB/XNES...
3.2 PCB LOCATIONS CD Core Unit (S11.1STD-DOUT) Tuner Amp Unit Keyboard Unit A:DEH-2350UB/XNES B:DEH-2350UBG/XNES C:DEH-2350UBSW/XNES D:DEH-2350UB/XSES E:DEH-2350UB/XNES1 Unit Number : CWN5489 (A, B, D, E) : CWN5479 (C) Unit Name : Tuner Amp Unit Unit Number Unit Name : Keyboard Unit...
Capacitor Bond Lock 3.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-2350UB/XNES...
B.UP Q752 VO1- VO2+ VO2- VDCONT VO3+ SPINDLE MOTOR LDIN LOEJ VO3- CLCONT LCOM RESET RESET LOADING/CARRIAGE VO4+ MUTE CONT RESET CDRST LCOP MOTOR VO4- CD DATA (CDSRQ,CDSTBY,SKIP, CD DATA (CDSRQ,CDSTBY,SKIP, SCL,SDA,DATA,BCLK,LRCK,WAIT) SCL,SDA,DATA,BCLK,LRCK,WAIT) DSCSNS HOME S903 S901 DSCSNS HOME DEH-2350UB/XNES...
In case of the above signal, the communication Source keys with Grille microcomputer may fail. operative If the time interval is not 300 msec, the oscillator may be defective. Source ON SYSPW <- H Pin 7 Completes power-on operation. (After that, proceed to each source operation) DEH-2350UB/XNES...
• How to restore from each error is shown below. classification, shown below. 0x, 1x and 3x: ACC-OFF then ON, CD-OFF then ON, 0x: Servo-related errors Disc ejection 1x: Servo-related errors 5X: ACC-OFF then ON, Disc ejection, Disc reloading 3x: Servo-related errors 5x: Mechanism-related errors DEH-2350UB/XNES...
Page 18
USB memory memory and do consumes more not use it. Turn the than maximum ignition switch to allowable cur- OFF, then to ACC rent. or ON and then connect a compli- ant USB portable audio player/USB memory. DEH-2350UB/XNES...
The screen gets still when entering this item. On (an initial value or On (state when setting value of default entering test mode) Switching to next display menu) by pressing “ 1 ” + “ 3 ” keys simultaneously. DEH-2350UB/XNES...
When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows) DEH-2350UB/XNES...
Lift off the Tuner Amp Assy from the Heat sink side. The Tuner Amp Unit is fixed into the ditch. Disconnect the FFC and then remove the CD Mechanism Module. CD Mechanism Module Fig.4 DEH-2350UB/XNES...
Page 23
Remove the two screws. Straighten the tabs at two locations indicated and then remove the Tuner Amp Unit. Fig.5 Tuner Amp Unit Attention of removing (Fig.6) Don't remove this screws excluding the dismantlement of the CD Mechanism Module. Fig.6 DEH-2350UB/XNES...
Page 24
1. Attach the button from the front side of the panel. Fig.9 2. Attach the spring to the arm as shown in the figure. The bended tip of the spring is set to this side. Hitch the spring to the groove. Fig.10 DEH-2350UB/XNES...
Page 25
4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel. Fig.11 DEH-2350UB/XNES...
Page 26
2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less) Correct way of holding the unit Incorrect way of holding the unit DEH-2350UB/XNES...
Page 27
1. Create an empty clamp state according to “How to create empty clamp state of mecha module”. 2. Apply 1.5 V to the CRG motor and move the PU to the outer circumference. (Caution) After moving the PU to the outer circumference and performing necessary treatment, make sure to solder the lead wires. DEH-2350UB/XNES...
1k ohms in series. The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-2350UB/XNES...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-2350UB/XNES...
With the TESTIN (22 pin) status of IC601 to be “H”, it is shifted to PCL Output Test mode after reset started. Check that square wave of 600.0 kHz is output from PCL (8 Pin) of IC601. If clock signal is out of this range, this resonator (X602) must be changed for a new one. DEH-2350UB/XNES...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING DEH-2350UB/XNES...
Page 33
Handle QNC3021 14-3 Service Network See Contrast table (2) Screw Assy YEA5082 Polyethylene Bag CEG-127 (2) CONTRAST TABLE DEH-2350UB/XNES, DEH-2350UBG/XNES, DEH-2350UBSW/XNES, DEH-2350UB/XSES and DEH-2350UB/ XNES1are constructed the same except for the following: DEH-2350UB/ DEH-2350UBG/ DEH-2350UBSW/ DEH-2350UB/ DEH-2350UB/ Mark Description XNES...
Page 35
See Contrast table (2) Cover CNS7068 Door See Contrast table (2) Lighting Conductor QNV3022 Rubber Contact QNV3023 (2) CONTRAST TABLE DEH-2350UB/XNES, DEH-2350UBG/XNES, DEH-2350UBSW/XNES, DEH-2350UB/XSES and DEH-2350UB/ XNES1are constructed the same except for the following: DEH-2350UB/ DEH-2350UBG/ DEH-2350UBSW/ DEH-2350UB/ DEH-2350UB/ Mark Description XNES...
ILMGND SW5V ILMG DGND ILMGND C803 DGND DGND C802 The > mark found on some component parts indicates the importance of the safety factor of the part. GRILL Therefore, when replacing, be sure to use parts of identical designation. DEH-2350UB/XNES...
Page 39
1u/10 TUNER AMP UNIT C208 1u/10 C206 1u/10 C234 CCG1192-A (DCH1201-A) C235 R232 E-VOL FM(30%): -5.9 dBs A : DEH-2350UB/XNES AM(30%): -5.9 dBs AUX:+10.3 dBs B : DEH-2350UBG/XNES CD/USB:+10.2 dBs C205 1u/10 C209 1u/10 C : DEH-2350UBSW/XNES main C207 1u/10...
MOTOR DRIVER LOGIC TABLE PowVcc2 1u/10 VO1- VO4- LOAD PLAY (1608) (1608) VO1+ VO4+ CLCONT VO2- VO3- LOEJ SWITCHES: CD CORE UNIT VO2+ VO3+ CONT S901:HOME SWITCH..ON-OFF IC301 S903:DSCSNS SWITCH..ON-OFF BA5839FP S905:8EJ SWITCH....ON-OFF The underlined indicates the switch position. PGND DEH-2350UB/XNES...
Page 47
3.3V LRCK 10 GND R606 BCLK DATA 11 DATA NM (1608) DATA BCLK 12 BCLK LRCK 13 LRCK AAGND1 AAGND2 14 GND 15 PGND /WAIT 16 WAIT i h g PGND NO MOUNT PARTS (NM) Land for manual soldering DEH-2350UB/XNES...
500 s/div fRFAGC 500 mV/div 500 mV/div 500 mV/div 9TIN 500 mV/div Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3) Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: TEST TEST TEST DEH-2350UB/XNES...
Page 49
12 cm CD Eject operation Ref.: Ref.: Ref.: REFO AGND Mode: Mode: Mode: Normal Normal Normal fRFAGC 1 V/div 500 s/div 9TIN 1 V/div 1 V/div aFIN 1 V/div Black Dot (800 m) during play Ref.: REFO Mode: Normal DEH-2350UB/XNES...
2.Viewpoint of PCB diagrams PRE OUT C259 Capacitor Connector JA251 SIDE A C316 Q251 R252 C252 C260 Q252 P251 C251 C313 C254 C253 D502 C261 SIDE B IC501 Chip Part P.C.Board C505 C503 R501 C502 R503 R502 R506 IC502 R507 CN701 FRONT DEH-2350UB/XNES...
PC board. IC 301 (A, 91, 111) IC NJM2068V Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. Q 752 (A,137,132) Chip Transistor RN4983 A:DEH-2350UB/XNES B:DEH-2350UBG/XNES Q 872 (A,146,52) Transistor LTC114EUB Q 873 (A,147,58) Transistor LSA1576UB C:DEH-2350UBSW/XNES...
Page 59
R 561 (A,119,84) RS1/16SS103J R 811 (A,122,26) RS1/10SR222J R 812 (A,102,25) RS1/10SR222J R 562 (A,118,80) RS1/16SS473J R 601 (A,112,85) RS1/16SS103J R 813 (A,100,25) RS1/10SR222J R 602 (A,109,82) RS1/16SS473J R 819 (A,105,12) RS1/10SR0R0J R 603 (A,111,85) RS1/16SS104J R 820 (A,118,30) RS1/10SR101J DEH-2350UB/XNES...
Page 60
C 314 (A,61,135) CCSSCH100D50 C 607 (A,128,73) CKSSYB104K10 C 315 (A,84,129) CCSSCH100D50 C 317 (A,62,136) CCSSCK1R0C50 C 608 (A,100,71) CKSSYB104K10 C 609 (A,127,70) CKSSYB104K10 C 318 (A,107,129) CCSRCH100D50 C 610 (A,100,69) CKSSYB104K10 C 319 (A,103,129) CCSRCH100D50 C 612 (A,130,69) CKSSYB104K10 DEH-2350UB/XNES...
Page 61
RS1/10SR272J R 1895 (B,56,12) (A,C,D,E) RS1/10SR272J MISCELLANEOUS R 1896 (B,139,20) (A,C,D,E) RS1/10SR272J IC 1801 (B,88,24) IC PD6340A R 1897 (B,16,13) (A,C,D,E) RS1/10SR272J IC 1802 (A,160,35) Remote IC GP1UXC14RK R 1898 (B,48,6) (A,C,D,E) RS1/10SR102J D 1868 (A,11,42) LED(RED) (A,C,D,E) SML-D12V8W(PQ) DEH-2350UB/XNES...
Page 62
R 283 (B,32,18) RS1/16SS0R0J R 291 (B,31,17) RS1/16SS560J R 292 (B,32,16) RS1/16SS0R0J R 293 (B,32,11) RS1/16SS0R0J R 294 (A,18,28) RS1/16SS471J R 296 (B,32,30) RS1/16SS0R0J R 299 (B,31,13) RS1/16SS0R0J R 305 (A,60,34) RS1/16SS183J R 306 (A,61,37) RS1/16SS183J R 307 (A,58,34) RS1/16SS183J DEH-2350UB/XNES...