The AEL (accessible emission level )of the laser power output is less than CLASS 1 but the laser component is capable of emitting radiation exceeding the limit for CLASS 1. u163 A specially instructed person should do servicing operation of the apparatus. DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 3
When Q101 is shorted between their terminals, the laser diodes will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam. L 13942296513 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DEH-23UB/XSUC http://www.xiaoyu163.com...
10.2 KEYBOARD UNIT ..........................46 10.3 CD CORE UNIT (S11.1STD-DOUT) ......................48 10.4 WAVEFORMS............................50 11. PCB CONNECTION DIAGRAM ........................52 11.1 TUNER AMP UNIT ..........................52 11.2 KEYBOARD UNIT ..........................56 11.3 CD CORE UNIT (S11.1STD-DOUT) ......................58 12. ELECTRICAL PARTS LIST ...........................60 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
If the lead is bent, please correct the angle between the lead and the light receiving part to be 90 degrees or replace the infrared deteching unit for remote control (GP1UXC14RK). u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 7
* length of tape : 24 ± 4 mm 10. Capacitor Bond Lock (ID) Silicon Glue (GEM1017) Place the capacitor in the center of the silk print, and confirm it does not touch to the connector. Then, apply silicon glue. L 13942296513 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. L 13942296513 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
State Tuner: band and frequency CAUTION Main dis- Program service name play sec- Use an optional Pioneer USB cable (CD-U50E) (DEH-2390UB/XNID) tion to connect the USB audio player/USB mem- Built-in CD player and USB: L 13942296513 ory as any device connected directly to the...
4 Front speaker 5 Rear speaker If you do not plan to detach the front panel, 6 White the front panel can be fastened with the supplied 7 White/black screw. u163 Screw UC : BPZ20P060FTC ID : XXX7020 DEH-23UB/XSUC http://www.xiaoyu163.com...
See the table below for the items to be checked regarding audio: Item to be checked regarding audio Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted L 13942296513 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
3.2 PCB LOCATIONS 3 7 63 1515 0 CD Core Unit (S11.1STD-DOUT) Tuner Amp Unit L 13942296513 Keyboard Unit A:DEH-23UB/XSUC B:DEH-2390UB/XNID Unit Number : CWN5640(A) : CWN5489(B) Unit Name : Tuner Amp Unit Unit Number Unit Name : Keyboard Unit...
Before shipping out the product, be sure to clean the L 13942296513 following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
VO2- VDCONT SPINDLE VO3+ MOTOR LDIN LOEJ VO3- CLCONT LCOM MUTE RESET RESET LOADING/CARRIAGE VO4+ CONT RESET CDRST LCOP MOTOR VO4- CD DATA (CDSRQ,CDSTBY,SKIP, CD DATA (CDSRQ,CDSTBY,SKIP, SCL,SDA,DATA,BCLK,LRCK,WAIT) SCL,SDA,DATA,BCLK,LRCK,WAIT) u163 DSCSNS HOME :DEH-23UB/XSUC S903 S901 DSCSNS HOME :DEH-2390UB/XNID DEH-23UB/XSUC http://www.xiaoyu163.com...
Source keys with Grille microcomputer may fail. operative If the time interval is not 300 msec, the oscillator may be defective. Source ON SYSPW <- H Pin 7 u163 Completes power-on operation. (After that, proceed to each source operation) DEH-23UB/XSUC http://www.xiaoyu163.com...
• How to restore from each error is shown below. classification, shown below. 0x, 1x and 3x: ACC-OFF then ON, CD-OFF then ON, u163 0x: Servo-related errors Disc ejection 1x: Servo-related errors 5X: ACC-OFF then ON, Disc ejection, Disc reloading 3x: Servo-related errors 5x: Mechanism-related errors DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 20
USB memory memory and do consumes more not use it. Turn the than maximum ignition switch to allowable cur- OFF, then to ACC rent. or ON and then connect a compli- ant USB portable audio player/USB memory. u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
The screen gets still when entering this item. On (an initial value or On (state when setting value of default entering test mode) Switching to next display menu) by pressing “ 1 ” + “ 3 ” keys simultaneously. u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows) DEH-23UB/XSUC http://www.xiaoyu163.com...
Lift off the Tuner Amp Assy from the Heat sink side. The Tuner Amp Unit is fixed into the ditch. Disconnect the FFC and then remove the CD Mechanism Module. u163 CD Mechanism Module Fig.4 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 25
Straighten the tabs at two locations indicated and then remove the Tuner Amp Unit. Fig.5 Tuner Amp Unit Attention of removing (Fig.6) L 13942296513 Don't remove this screws excluding the dismantlement of the CD Mechanism Module. Fig.6 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 26
1. Attach the button from the front side of the panel. Fig.9 2. Attach the spring to the arm as shown in the figure. The bended tip of the u163 spring is set to this side. Hitch the spring to the groove. Fig.10 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 27
4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel. Fig.11 L 13942296513 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 28
2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less) Correct way of holding the unit Incorrect way of holding the unit L 13942296513 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 29
1. Create an empty clamp state according to “How to create empty clamp state of mecha module”. 2. Apply 1.5 V to the CRG motor and move the PU to the outer circumference. (Caution) After moving the PU to the outer circumference and performing necessary treatment, make sure to solder the lead wires. u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
1k ohms in series. The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint u163 Reloading the disc changes the clamp position and may decrease the "wobble". DEH-23UB/XSUC http://www.xiaoyu163.com...
Check that square wave of 600.0 kHz + 25 Hz is output from PCL (8 Pin) of IC601. If clock signal is out of this range, this resonator (X602) must be changed for a new one. L 13942296513 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
9. EXPLODED VIEWS AND PARTS LIST 3 7 63 1515 0 9.1 PACKING L 13942296513 u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 35
See Contrast table (2) 17-3 Service Network See Contrast table (2) Polyethylene Bag CEG1160 Handle QNC3021 (2) CONTRAST TABLE DEH-23UB/XSUC and DEH-2390UB/XNID are constructed the same except for the following: Mark Description DEH-23UB/XSUC DEH-2390UB/XNID Polyethylene Bag CEG1374 QEG3001 Unit Box...
Page 37
See Contrast table (2) Label See Contrast table (2) Lighting Conductor QNV3022 Rubber Contact QNV3023 L 13942296513 (2) CONTRAST TABLE DEH-23UB/XSUC and DEH-2390UB/XNID are constructed the same except for the following: Mark Description DEH-23UB/XSUC DEH-2390UB/XNID Tuner Amp Unit CWN5640 CWN5489 Holder...
MECHA VD 751 - 800 ILMG DGND ILMGND C803 DGND DGND C802 The > mark found on some component parts indicates the importance of the safety factor of the part. GRILL Therefore, when replacing, be sure to use parts of identical designation. DEH-23UB/XSUC http://www.xiaoyu163.com...
MOTOR DRIVER LOGIC TABLE PowVcc2 1u/10 VO1- VO4- LOAD PLAY (1608) (1608) VO1+ VO4+ CLCONT VO2- VO3- LOEJ SWITCHES: CD CORE UNIT VO2+ VO3+ CONT u163 S901:HOME SWITCH..ON-OFF IC301 S903:DSCSNS SWITCH..ON-OFF BA5839FP S905:8EJ SWITCH....ON-OFF The underlined indicates the switch position. PGND DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 49
10 GND R606 BCLK DATA 11 DATA NM (1608) DATA BCLK 12 BCLK LRCK 13 LRCK AAGND1 AAGND2 14 GND 15 PGND /WAIT 16 WAIT i h g PGND u163 NO MOUNT PARTS (NM) Land for manual soldering DEH-23UB/XSUC http://www.xiaoyu163.com...
500 mV/div 500 mV/div 500 mV/div 9TIN 500 mV/div Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3) Ref.: Ref.: Ref.: REFO REFO REFO u163 Mode: Mode: Mode: TEST TEST TEST DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 51
12 cm CD Eject operation Ref.: Ref.: Ref.: REFO AGND Mode: Mode: Mode: Normal Normal Normal L 13942296513 fRFAGC 1 V/div 500 s/div 9TIN 1 V/div 1 V/div aFIN 1 V/div Black Dot (800 m) during play Ref.: REFO Mode: Normal u163 DEH-23UB/XSUC http://www.xiaoyu163.com...
12. ELECTRICAL PARTS LIST 3 7 63 1515 0 Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. Q 931 (A,118,105) Transistor LSC4081UB A:DEH-23UB/XSUC D 301 (A,100,127) Diode CRG03 B:DEH-2390UB/XNID D 302 (A,97,127) Diode CRG03 Unit Number : CWN5640(A)
(A,100,67) RS1/16SS222J R 874 (A,148,55) RS1/16SS103J R 611 (A,132,69) RS1/16SS101J R 911 (A,141,41) RS1/10SR1R0J R 612 (A,98,79) RS1/16SS473J R 912 (A,144,42) RS1/10SR1R0J R 613 (A,132,68) RS1/16SS101J R 931 (A,121,106) RS1/16SS223J R 615 (A,98,64) RS1/16SS104J R 932 (A,118,107) RS1/16SS473J DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 62
(A,150,100) CKSSYB104K10 C 622 (A,124,53) CKSSYB104K10 C 405 (A,147,100) CKSSYB104K10 C 623 (A,119,53) CKSSYB104K10 C 624 (A,118,52) CKSSYB104K10 C 406 (A,160,101) CKSSYB103K16 C 407 (A,148,100) CKSSYB104K10 C 625 (A,117,53) CKSSYB104K10 C 409 (A,162,101) CKSSYB103K16 C 626 (A,115,53) CKSSYB104K10 DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 63
RS1/16SS105J D 1876 (A,54,29) LED(RED) SML-D12V8W(PQ) R 109 (B,11,52) RS1/16SS222J D 1877 (A,71,6) LED(RED) SML-D12V8W(PQ) D 1878 (A,83,6) LED(RED) SML-D12V8W(PQ) R 214 (A,38,41) RS1/16SS103J D 1879 (A,95,6) LED(RED) SML-D12V8W(PQ) R 215 (A,38,40) RS1/16SS393J D 1880 (A,143,9) LED(RED) SML-D12V8W(PQ) DEH-23UB/XSUC http://www.xiaoyu163.com...
Page 64
CKSSYB104K10 C 220 (B,32,41) CKSSYB104K10 C 221 (A,35,43) CKSSYB104K10 C 222 (A,29,43) CKSSYB104K10 C 223 (A,25,44) CCSSCH680J50 u163 C 224 (A,23,44) CCSSCH470J50 C 225 (A,20,43) CKSSYB103K16 C 228 (A,32,46) CCSSCH270J50 C 229 (B,28,40) CKSSYB104K10 C 231 (B,44,28) CKSSYB102K50 DEH-23UB/XSUC http://www.xiaoyu163.com...