Advertisement
! Important: Check that the voltage marked on the transformer plug is the same as the power supply to be used.
! Uncoil the power cable between the transformer and the charging base before use.
% DO NOT pull or carry the charging base by the transformer power lead, or pull the transformer plug from the mains socket by the power lead.
% DO NOT use any other type of transformer with the charging base.
% DO NOT place the power connector into any area of charging base except the correct socket (beneath the green power light bulb).
% DO NOT try to open or dis-assemble the transformer plug or charging base.
% DO NOT use the transformer plug to power any other electrical item.
% DO NOT get the transformer wet, or use in wet, damp conditions (for indoor use only).
F WARNING! NEVER substitute a standard 13Amp 3 pin plug, or any other type of plug, for the transformer plug .
1.4.
BATTERY CHARGING BASE SAFETY INSTRUCTIONS.
F WARNING! DO NOT use the charging base to charge any battery other than that supplied for the drill. Other types of batteries may explode!
! All mains electrical supply safety features must be followed as described in 1.3. above.
! Disconnect the transformer plug from the charging base and the mains power supply when not in use.
% DO NOT expose the charging base to damp or wet conditions (for indoor use only).
% DO NOT pull or carry the charging base by the transformer power lead.
% DO NOT operate the charging base if it has been dropped, or has received a sharp knock, or is damaged. Contact an authorised service agent.
% DO NOT dismantle the charging base as this may cause damage or personal injury and will invalidate your warranty.
% DO NOT insert foreign objects or material into the hole reserved for the battery.
% DO NOT force the battery into the charging base. The battery will only fit one way to ensure correct polarity alignment.
% DO NOT immediately charge a second battery. Consecutive charging will overheat the charging base. Allow the unit to cool for 15 minutes
before charging the next battery.
% DO NOT attempt to connect two charging bases together.
! Store the charging base in the same manner as battery, see para. 1.2.
2. SPECIFICATIONS
Chuck size . . . . . . . . . . . . . . . . . . . . . . . . . .10mm
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18V
No load speed . . . . . . . . . . . . . . . . . . . . .1000 rpm
Max torque . . . . . . . . . . . . . . . . . . . . . . .110 kg.cm
Full charge time . . . . . . . . . . . . . . . . . .3 - 5 hours
HSS Drill Bits . . . . . . . . . . . . . . . . .2, 3, 4, 5, 6mm
Screwdriver Bits . . . . . . . . . . . .Slotted 5mm, 6mm
Double ended - Phillips #1 x Slotted 5mm
- Phillips #2 x Slotted 7mm
Sockets . . . . . . . . . .5, 6, 7, 8, 9, 10mm + adaptor
Operating capacity on one charge.
Approximate, depending on material, drill sharpness, drill/screw diameter etc. and please note that
full battery capacity will only be achieved after several charges.
Drilling - wood . . . .126 holes x 25mm deep
metal . . . . 6 holes x 16mm deep
3. OPERATING INSTRUCTIONS
Note: When new, the battery will have been shipped in a low charge state. It will take longer to charge the battery initially (about 8 hours) and
several subsequent charges may also take a little longer than when the battery reaches its optimum performance.
3.1.
Charging the battery pack.
3.1.1. To remove the battery pack from the drill, depress the two side clips (fig.1 item 7).
Do not touch the metal battery terminals.
3.1.2. Place drill in carrying case and remove the battery charging base and transformer plug.
3.1.3. Connect mains transformer to the charging base (fig.2) and place the base on a safe flat surface.
Plug the transformer into mains socket and switch on. The green power light will come on.
3.1.4. The battery is designed to fit into the charging base one way only. This is to ensure that the
positive (+) and negative (-) polarities correspond. Align the + and - polarity marks on the base
of the battery with the + and - marks on the charging base, insert the battery and press lightly to
seat the battery firmly into the charging base, as in fig.2.
WARNING! DO NOT try to force battery into the base with crossed polarities.
3.1.5. The red charge light will come on when the battery is inserted into the charging base, and will remain on until
the battery is removed from the base. Under normal conditions the battery will take 3 - 5 hours to fully charge from flat.
NOTE: It will take about 8 hours for the initial charge (see Section header note).
3.1.6. Remove the battery from the charging base and the red light will go out. Switch off and unplug the
transformer from the mains. Push the battery into the drill base until it latches into place. The drill is now ready for use.
3.1.7. Place the transformer plug and charging base back into the case.
Note: Attempting to recharge a battery immediately after use may result in the red charge light not coming on. In such a case allow the
battery to cool for a time and try again.
3.2.
Drilling instructions. (Ensure you have read, understood and comply with all the safety instructions)
WARNING! always wear approved safety glasses when drilling.
3.2.1. Preparation
1. Open the chuck by holding the rear collar (fig.3 ‘B’) and turning the front chuck collar (fig.3 ‘A’)
See direction arrow on chuck.
2. Insert the required drill bit into the full length of the chuck and tighten.
3. Check the drill to ensure the direction switch (fig.1 item 3) is in the mid (lock) position.
4. Insert the battery pack into the base of the drill and latch into place.
5. The speed of the drill is controlled by the electronic variable speed switch (fig.1 item 4). After moving
direction switch to ‘forward’ (or ‘reverse’) press the speed switch gently for a slow speed and progressively increase the pressure on
the switch to produce correspondingly higher speeds (try before starting to drill).
1. Keyless chuck
2. Torque setting ring
3. Lock, reverse and forward switch
4. Electronic variable speed switch
5. Double bit holder
Phillips #1, #2
6. Battery pack
7. Battery release button (one each side)
8. Charging base
9. Mains transformer plug
Screw-driving - 200 screws x 30mm long
fig. 1
fig. 2
green - power
indicator
red - charging
indicator
cable from
transformer plug
fig. 3
CP18V - 1022 - (1) - 180599
Advertisement
