Advertisement
3.2.2. Torque setting
Torque is the amount of turning force applied when you use the drill.
Torque setting ‘1’ (fig.4 ‘C’) is the lowest and will apply the least effort - to the final turns of a screw, for example.
The torque becomes progressively greater with increased setting numbers, up to a maximum of ‘6’.
The combination of variable speed and torque gives maximum drilling efficiency.
Suggested torque settings:
3.2.3. To drill holes
Lock a pilot drill (smaller size drill than the finished hole size) into the chuck.
Select an appropriate torque setting (para. 3.2.2.).
Check to confirm the turning direction is correct (change by direction switch, fig.1 item 3).
DO NOT attempt to change direction whilst the drill is running.
Drill a pilot hole in the middle of the spot where the final hole is to be drilled.
Insert the final sized drill bit. Hold drill firmly and place the drill bit at the entrance of the pilot hole and press the trigger as in 3.2.1.
If the drill becomes stuck, release the switch and place the chuck in reverse by pressing the direction switch to the other side (fig.1 item 3).
If this does not work, gently work the drill bit free. If the chuck stops turning, check the torque setting.
3.2.4. As a screw or bolt driver.
Lock appropriate tool bit in the chuck, set appropriate torque and proceed with the task. To remove screws, bolts, etc., switch the drill to reverse.
3.2.5. When you have finished working, remove the bit from the chuck, clean drill and bit and store in the carry case.
4. PARTS LIST
ITEM
PART No
DESCRIPTION
4
NA1298/04
Cover, front top
6
NA1298/06
Holder, metal bit
7
NA1298/07
Holder, connector plate
8
NA1298/08
Plate, contact
9
NA1298/09
Rivet
10
CP18V/10
Switch, variable speed
11
CP18V/11
Charging base
Declaration of Conformity
Cordless Drill, Charging Unit &
Transformer Plug
Model CP18V
73.23/EEC LV Directive (S.I. 1994/3260)
89/336/EEC EMC Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: For a copy of our latest catalogue, call us on 01284 757525 and leave your full name and address, including postcode.
1. Small screws
2. Screws into soft material
3. Screws into hard material
ITEM
PART No
12
NA1298/12
13
CP18V/13
14
NA1298/14
15
NA1298/15
16
NA1298/16
19
NA1298/19
20
NA1298/20
We, the sole importer into the UK, declare that the products listed below are in conformity with the following EEC standards and directives.
The construction files for these products are held by the Manufacturers and may be inspected on
request by contacting Jack Sealey Ltd
Signed by Mark Sweetman
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
4. Screws into hard wood
5. Regular drilling
6. Heavy drilling
DESCRIPTION
Cover housing
motor, 18v
Switch, reverse
Wire
Wire
Support, handle
Support housing
01284 703534
01284 757500
fig. 4
Origin Date:-
180599
Issue Date:-
230699
Version No:-
1
Date Modified:-
1st Issue
ITEM
PART No
DESCRIPTION
21
NA1298/21
Screw, self tapping
23
CP18V/23
Mains transformer
24
NA1298/24
Bit,screwdriver
29
NA1298/29
Chuck, 3/8” keyless
30
CB18/BP
Battery pack
31
CP18V/31
Gearbox assembly
For Jack Sealey Ltd.
1st May 1999
Sole importer into the UK
of Sealey Power Products
E-mail: sales@sealey.co.uk
CP18V - 1022 - (1) - 180599
Advertisement
