Some chemicals or detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury. • Do not allow CHILDREN to operate the Pressure Washer at any time. PREPARATION: • Operate engine only at governed speed.
Page 3
NUMBER SOLID STATE IGNITION AIR GAP NOTE: The engine of the pressure washer is equipped with a spark arrestor muffler, The spark arrestor must be main- tained in effective working order by the owner/operator` . In the State of California a spark arrestor is required by law (Section 4442 of the California Public Resources Code).
Page 5
ACCESSORIES These accessories and attachments were available when the high pressure washer was purchased. They are also vailable at most Sears retail outlets and service centers. Most Sears stores can order these items for you when you ,_rovide the model number of your high pressure washer.
Page 6
CONTENTS Main Unit Wheels High Pressure Hose Wire Support (2) Push Nuts - 1/2" Parts packed in carton shown full size (2) Axle Pins lllI!II!fl!lllllltlttttlltllliiiitiB 2) Hex Head Capscrews- M8 x 40mm tlttlllllNllll!ll 4) He× Head Cap_mws - M8 × 20ram OF HARDWARE Parts packed separately in carton Parts Carton...
Read these instructions and Operator's Manual in its en- tirety before you attempt to assemble or operate your new high pressure washer. Your high pressure washer has, for he most part, been assembled at the factory, except those )arts left unassembled.
Page 8
Provide proper water supply (not to exceed 140°F). INLET SCREEN • Be sure to read "Safety Rules" and "Operation" se_ tions before using the pressure washer, FIG. 6 HIGH PRESSURE HOSE FIG. 7 nozzle,...
Page 9
KNOW YOUR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. WIRE SUPPORT FOR...
NOTE: A small amount of water will squirt out when you release the pressure. SPRAY NOZZLES Your high pressure washer comes equipped with an adjust- able nozzle (Fig. 10) or you can order the optional turbo nozzle (Fig. 11). Attach either nozzle as shown in Fig, 10...
Leavethe solution on surface for 3 to 5 minutes to allow solution to worK. The second step involves cleaning the surface you have prepared with the pressure washer and then rinsing it clean. To apply detergent follow these steps:...
ADD ENGINE OIL: Place pressure washer on a level surface and remove one of the yellow Oil Fill Caps (Fig, 17) and add engine oil from the enclosed bottle unttl level is at point of overflowing. Check engine oil level before starting each time thereafter.
Page 13
You can also turn the pressure control knob to your desired pressure setting. • Your pressure washer is ready to use. IMPORTANT: AN INTERNAL THERMAL RELIEF VALVE HAS A MAXIMUM TEMPERATURE (60°C). IF YOU RUN THE PUMP FOR 5 MINUTES WITH-...
*Change, scoam'when oporati_,g u_texheavyloadorhighambi_nt GENERAL RECOMMENDATIONS The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or neg- ligence. To receive full value from the warranty, operator must maintain high pressure washer as instructed in this manual.
Purge Pump of Air and Contaniments: To remove the air from the pump, follow these steps: Set up the pressure washer as described in the AS- SEMBLY section and connect the water supply. Remove the nozzle attachment from the gun.
WARNING: WORKING CLEANER FLER OR ENGINE CAN CAUSE SEVERE BURNS, NOTE: If you use your pressure washer on any forest-cov- ered, brush-covered must have a spark arrestor. maintained in good condition by the owner/operator. Clean and inspect the spark arrestor as follows:...
PAIR AND ADJUSTMENT, GOVERNED SPEED WILL VOID ENGINE WAR- RANTY. Your pressure washer runs at a constant speed. constant operating speed is maintained by a mechanical, flyweight type, fixed speed governor. DO NOT try to adjust the governed speed setting for the following reasons: High engine speeds are dangerous and increase the risk of personal injury or damage to equipment.
WATER HEATER, OR OTHER GAS APPUANCEo If you do not plan to use the Pressure Washer for more than 30 days, you must prepare the engine for long term storage. • Test the pressure washer by operating with nozzle in the high and in the tow position.
PROBLEM Pump has following problems: failure to producepressure,erratic pressure,chattering,loss of pressure, low water volume. Detergent fails to mix with spray. Engine runs good at no-lead but "bogs Enginewill not start;or starts and runs rough , ,,,,,_,,,,, ,,,,,, ... Engine shutsdown during operation Engine lacks power.
Sears will repair, free of charge, any defect in material and workmanship. If the Craftsman Engine is used for commercial or rental purposes, this warranty applies for only one year from the date of purchase, This warranty does not cover: •...
Page 28
Each High Pressure Washer has its own model number. Each engine has its own part number. Each engine has its own model number. The model number for your pressure washer will be found on a decal attached to the unit.