Sealey VSE5312.V2 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
Instructions Protection
1. SAFETY
WARNING! Wear approved eye protection. Wear appropriate Personal Protective Equipment. A full range of Personal Protective
‰
Equipment is available from your Sealey stockist.
WARNING! Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to
‰
when using tools.
DO NOT use tools if damaged.
8
Maintain tools to ensure that they are in an adequate condition for safe use and optimum performance.
9
Ensure that a vehicle that has been raised by a jack is adequately supported. Use axle stands.
9
Wear suitable clothing to avoid snagging. DO NOT wear jewellery. Tie back long hair.
9
Account for all tools, parts and components being used. DO NOT leave these in or near the engine. Return tools to suitable
9
storage after use.
▲ IMPORTANT! These Instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions or a
proprietary manual to establish the correct procedure and data.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations. The
‰
Operator / user must apply caution and common sense (good practical sense).
When timing an engine, always prevent the engine from being turned over. Use a notice and/or inhibit the engine.
9
WARNING! Incorrect or out of phase camshaft timing can result in contact between the valve head and the piston crown. This will
‰
cause damage to the engine.
2. INTRODUCTION
Used to position and lock the high pressure fuel pump into its timed position when changing the fuel pump drive belt.
3. APPLICATIONS
MODELS:
Jaguar: XF (09-18), XJ (09-14), F-Pace (16-18)
Land Rover:
Discovery 3 (04-09), Discovery 4 (09-20),
Range Rover L405 (12-20), Range Rover Sport (09-20),
Range Rover Velar (17-20)
ENGINE:
3.0 TDV6: 306DT, AJ-V6D/306DT
OEM TOOLS:
Jaguar,
Land Rover: 310-212
ASSOCIATED TOOLS: VSE5000A - Diesel engine timing tool kit - Land Rover, Jaguar, Citroen, Peugeot 2.7D, 3.0D - Belt Drive
4. OPERATION
NOTE: The Sealey VSE5312 Fuel Pump Holding Tool should be used in conjunction with the Sealey VSE5000A Setting and Locking
Kit.
4.1. REMOVAL
4.1.1. Remove the rear engine cover and right hand bulkhead cover.
4.1.2. Disconnect and seal off the EGR coolant hoses.
4.1.3. Remove steering column lower joint bolt and disconnect the steering angle sensor multi-plug.
4.1.4. Remove steering rack mounting bolts to gain access to starter motor, remove starter motor.
4.1.5. Remove the high-pressure fuel pump belt cover.
4.1.6. Turn the crankshaft clockwise until the timing marks are aligned.
4.1.7. Fit the appropriate Flywheel Locking Tool from the VSE5000A Setting and locking Kit, and secure it using a starter motor bolt.
4.1.8. Remove the high fuel pump tensioner, and tensioner pulley.
4.1.9. Remove the high-pressure fuel pump belt.
© Jack Sealey Limited
FUEL PUMP HOLDING TOOL - JAGUAR,
LAND ROVER 3.0D - BELT DRIVE
VSE5312.V2
MODEL NO:
Original Language Version
VSE5312.V2 Issue:2 15/03/21