Kenwood 103AR Instruction Manual page 5

About the system control connections
1D3AR [En)
«
•m
Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient
system control operations.
There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown below.
Q(SBj
Mode: lets you combine
DR], DCS],
and
DCSB
terminals
GLIB
Mode: for
5LE1
terminals only
This unit is compatible with both (XS8J and [SL16] modes It comes from the factory set to the IXS8] mode. To switch to the [SL161
mode, follow the instructions in "SWITCHING FROM [XS8] TO [SL16]" below.
EXAMPLE: [XS8] mode connections
The underlined portion represents the setting of the system
control mode.
System
control
cord
System
control
cord
ISL16] [XS8]
[SL16]
[SL16] [XS] [XS8] [XR]
[SL16] [XS] [XS8]
[XS]
. Seme CD D aye's a-a cassette decks are not compat.oie with the ISL16! system, control mode. Be sure to use tne [XSSI system control
■ o oe wne-" m a King system connections with eauipment that <s not (SL1 6] compatible
• Seme MD P'avers am not system control compatible You cannot make system control connections to this kind of equipment.
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system
control mode.
[SLT6} [XS8]
[SL16]
[SL16] [XS] [XS8] [XR]
[SL163 [XS] [XS8]
[XS]
[SLl6i
equipment
cannot be combined
witr
[XRi. [XS], and [XS8] equipment for system opera¬
tions If yOur eou.oment consists of this moo of combinatton,
cptroi C0'ds. Even w mom system comro cords. nor
rVfectma oer'omnancc
h please do not connect any system
■ a ; operations can be earned out without
no' connect system control cords to any components other than those specified by
KENWOOD It may cause a malfunction and damage you' equipment.
do sure the syste'" control Dluas are inserted ali the way m to the system control terminals
ABOUT THE SYSTEM CONTROL OPERATIONS
Remote Control (Except ISL16])
Lets you operate source components with the system re¬
mote supplied with this unit.
Automatic Operation (Except [XR] equipment)
When you start playback from a source component, the in¬
put selector on this unit switches to that component auto¬
matically
Synchronized Recording (Except [XR] equipment)
Lets you synchronize recording with the start of playback
when recording from CD, MD, or analog discs
SWITCHING FROM [XS8J TO [SL 16]
You can easily change the system control mode with the
following operation. Do this operation after completing all
connections.
Switching to [SL16]:
Switching back to [XS8]:
Unplug the AC power cord from
the wall outlet, then plug it back
in while holding down the AUTO/
MANUAL key
Unplug the AC power cord from
the wall outlet, then plug it back
in while holding down the BAND
key .
• This operation wil not affect items stored in the memory
Note]
Tne system control mode will revert to [XS8] if the
cower cord is disconnected from the AC outlet for
th^ee consecutive aays. If you would like to make
:oe unit completely (and permanently) JSL16] com¬
patible. please consult your nearest retailer or the
KENWOOD Marketing Department
1 Connect all Coras
firmiy
i! connections are loose, mere could be loss of sound or noise produced.
2 l\ -.e- piuggmg and unplugging connection cords, be sure to first remove the power cord from the AC outlet Ptuqqmq / unpluo-
cmg connection cords without removal of tne aowe- cord car cause malfunctions or damage to the unit