Sealey ES300.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instructions gloves
1. SAfETy
ensure that the engine support is in good working order. Take action for immediate repair or replacement of damaged parts. Use
9
genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.
locate the vehicle in a suitable, well lit work area.
9
Keep work area clean and tidy and free from unrelated materials.
9
ensure the vehicle handbrake is engaged and the engine/motor is switched off.
9
ensure all non-essential persons keep a safe distance whilst the engine support is in use.
9
DO NOT use the engine support if damaged.
8
DO NOT allow untrained persons to operate the engine support.
8
DO NOT use the engine support for purposes other than that for which it is designed.
8
DO NOT exceed the rated capacity of the engine support.
8
When not in use, store engine support in a safe, dry, childproof area.
9
2. INTRODUcTION
designed to support and accurately position engines during maintenance operations such as replacing anti-vibration mountings and
certain body panels. Also used as an aid for the removal of gearboxes and transmissions. Beams Supported on rubber feet and fine
adjustment control is obtained by using a screw/hook mechanism. Supplied with a short length of chain.
3. SPEcIfIcATION
Maximum Capacity ..........................................................300kg
Minimum Width ..............................................................585mm
Maximum Width ...........................................................1580mm
Screw Travel ..................................................................230mm
Weight ..........................................................................12.12kg
4. cONTENTS
Item Part No. Description
1 eS300.V3-01 Handle bar grip
2 eS300.V3-02 operating clamp assembly
3 eS300.V3-03 Washer internal diameter 22mm
4 eS300.V3-04 Grip
5 eS300.V3-05 Washer internal diameter 13mm
6 eS300.V3-06 Standing block
7 eS300.V3-07 bolt 16mm and lock nut
8 eS300.V3-08 Foot
9 eS300.V3-09 Rubber block
10 eS300.V3-10 Adjustable screw
11 eS300.V3-11 Chain
12 eS300.V3-12 Beam
5. ASSEMBly INSTRUcTIONS
Note: numbers in brackets refer to item numbers shown in the parts diagram.
5.1. Put washer (3) over the threaded section of the standing block and slot it up through the outer section of the beam. Fit washer (5) on top
and secure using grip (4).
5.2. Remove the bolt (7) from the foot (8) fit standing block (6) and refit the bolt and tighten the nut.
5.3. Repeat paragraphs 3.1 and 3.2 at the other outer section of the beam (12).
5.4. Slot the threaded section of the adjustable screw (10) up through the centre slotted section of the beam (12), fit the washer (3) and
secure using the operating clamp assembly (2).
5.5. The engine support is now ready for use.
Note: Ensure both grips (4) and all nuts are tightened before applying a load.
© Jack Sealey limited
ENGINE SUPPORT BEAM 300KG
Model no:
Wear safety Wear protective
footwear clothing
Original Language Version
ES300.V3
fig.1
eS300.V3 Issue 2 (HF) 24/08/18