Sealey TR1000.V3 Instructions

TR1000.V3, TR1500.V3, TR2000.V3 & TR3000.V3
Model No:
ImPoRTANT: PLEASE READ THESE INSTRUCTIoNS CAREFULLY. NoTE THE SAFE oPERATIoNAL REQUIREmENTS, WARNINGS AND CAUTIoNS.
USE THE PRoDUCT CoRRECTLY AND WITH CARE FoR THE PURPoSE FoR WHICH IT IS INTENDED. FAILURE To Do So mAY CAUSE
DAmAGE AND/oR PERSoNAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIoNS SAFE FoR FUTURE USE.
1. SAFETY INSTRUCTIoNS
1.1. ELECTRICAL SAFETY
 WARNING! It is the user's responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged
into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by
contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by
a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year (see para.2.7).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs for wear and damage and all electrical connections
to ensure that none is loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply
to be used and check that plugs are fitted with the correct capacity fuse. A 13 amp plug may
require a fuse smaller than 13 amps for certain products, see fuse rating at right.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8. DO NOT pull plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have
repaired by a qualified electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage,
cut off and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the grEEn/YElloW earth wire to the earth terminal 'E'.
b) Connect the broWn live wire to live terminal 'l'.
c) Connect the bluE neutral wire to the neutral terminal 'n'.
After wiring, check there are no bare wires, that all wires have been correctly connected, that
cable outer insulation extends beyond the cable restraint and that the restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always
marked with this symbol
the earth terminal.
1.1.10. Some products require more than a 13 amp electrical supply. In such a case, NO plug will be fitted. You must contact a qualified
electrician to ensure a 30 amp fused supply is available. We recommend you discuss the installation of a industrial round pin plug and
socket with your electrician.
1.2 GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this

transformer.
familiarise yourself with the application and limitations of the transformer, as well as the potential hazards.

WARNING! Disconnect the transformer from the mains power before performing any maintenance.

Maintain the transformer in good condition (use an authorised service agent).

Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.

WARNING! Do NoT connect to mains if any parts are damaged or missing as this may cause failure and/or personal injury.

Keep the transformer clean for best and safest performance.

Keep children and unauthorised persons away from the working area.

Do NoT use the transformer for any purpose other than that for which it is designed.

Do NoT exceed the rated capacity of the transformer.

Do NoT allow untrained persons to use the transformer.

Do NoT use the transformer when you are tired, under the influence of alcohol, drugs or intoxicating medication.

Do NoT pull the plug from the power supply by the cable.

When not in use unplug from the mains power supply and store in a safe, dry, childproof area.

. To re-wire, connect the brown & blue wires as indicated above. Do noT connect the brown or blue to
INSTRUCTIONS fOR:
TooL TRANSFoRmERS
blue
neutral
Core
TR1000.V3, TR1500.V3, TR2000.V3, TR3000.V3
Yellow & green
Earth Core
brown
live
Core
Cable
restraint
FuSE rATIng
THIS PRoDUCT mUST BE FITTED
WITH A
13 AmP FUSE
Issue: 1 17/07/09