Advertisement
2. SPECIFIC SAFETY & USAGE
2.1.
The Tool Rating (kVA) marked on the transformer data plate is the rating assuming a 25% duty factor on a 20 minute cycle i.e. 5
minutes equipment use followed by 15 minutes rest.
2.2.
Check the equipment rating and operation against the transformer rating. The transformer will supply intermittently used equipment
up to the plate rating but if the equipment is used continuously then the transformer rating should be halved. See Section 3.
2.3.
It is normal for the transformer to get warm during use, particularly if being used continuously, so care should be taken to place
only on surfaces that will not be damaged by the heat.
2.4.
A temperature sensitive cut-out switch is fitted to prevent overheating. If this switch trips, determine and rectify the cause of
overheating and allow time for the transformer to cool before pressing the reset button. (Located on one of the sides adjacent to the
output sockets)
2.5.
The transformer should be plugged directly into a 230V mains socket and should not be supplied via an extension lead. Any
necessary extension lead should be between the transformer and the tool/equipment. Extension leads are available from your Sealey
dealer.
2.6.
The transformer is not double insulated and the safety screen between primary (230V) and secondary (110V) windings is connected to
the earth core of the power cable. for these reasons it is extremely important to confirm that the power socket to be used is reliably
and permanently earthed.
2.7.
Tool transformers can draw a very high initial current when switched on. If fuse failure occurs at switch-on check that the fuse is a
13 amp, anti-surge type. Any circuit breaker protecting the supply socket should have a type 4 tripping characteristic.
2.8.
Do NoT exceed 1.5kV when flash testing.
2.9.
A plug suitable for the transformer output is available from your supplier under Sealey Model No: TR110VP.
3. SPECIFICATIoNS
moDEL No:
TR1000.V3
Input Voltage - 1ph AC
output Voltage -
1ph AC
output Rating - (VA)
Tool (Intermittent)
output Rating - (VA)
Continuous
output Sockets
Declaration of Conformity
Tool Transformer
models: TR1000.V3, TR1500.V3,
TR2000.V3, TR3000.V3
2004/108/EC EMC Directive
2002/95/EC RoHS Directive
2002/96/EC WEEE Directive
93/68/EEC CE Marking Directive
2006/95/EC Low Voltage Directive
noTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
ImPoRTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFoRmATIoN: for a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
TR1500.V3
TR2000.V3
230
230
230
110
110
110
1000
1500
2000
500
750
1000
1
2
We, the sole distributor in the UK, declare that the products listed here are in conformity with the following standards and directives.
The construction files for these products are held by the Manufacturer and may be inspected
on request by contacting Jack Sealey Ltd.
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
TR3000.V3
230
110
3000
1500
2
2
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole distributor in the UK of Sealey Power Products.
01284 757500
01284 703534
TR1000.V3, TR1500.V3, TR2000.V3, TR3000.V3
17th July 2009
www.sealey.co.uk
Web
sales@sealey.co.uk
email
Issue: 1 17/07/09
Advertisement
