Advertisement
€1 (O9E0S°ON)
Front Panel
Remote Control
RETURN "SAP.
2
oF
VOLUME
2) CANCEL
Press "'2" to cancel the Guarded Channel. The display will show:
With this display on the screen, press the number of the Guard-
'ed Channel you wish to cancel from the list. For example, if
you wish to cancel CHANNEL 25 {in this case, Guarded Chan-
net 1) from the list, press '1'', Then the display changes to show
that CHANNEL 25 (Guarded Channel 1) has been cancelled.
CHANNEL GUARD
1 SET
2 CANCEL &
3.Se5 15 0
2 CABLE 13
3 CABLE 35
3) SET 10 NO.
Press "'3'' to set the ID number. The display will show:
Press any 3 digits you wish to be'the 1D number. When com-:
pleted, "ENTERED" appears to show that the 1D number you
have just keyed in is set.
1O.NQ IZSENTEREO
Viewing Guarded Channels
1) Select the Guarded Channel. {If the Guarded Channe! you
wish to view is CHANNEL 25, press "2" and "5%.) Then,
the following display appears:
ay
8
19 NO --~
2) Key in the 1D number using the 10-Digit Keypad. The chan-
nel appears.
3) If the keyed-in {1D number is incorrect, the display shows:
INVALID IO NOt
And the Guarded Channel you have selected cannot be seen.
Notes:
@
}f you wish to change the ID number, follow the steps of
"3) SET ID NO.".
@
If the power is disconnected
(such as in the case of power
failure, etc.}), and reapplied tater, the ID number is reset to
"000".
@ When performing the CHANNEL SCAN function, or select-
ing channels using CHANNEL (-/+) buttons @ , the Guard-
ed Channels are skipped.
:
®@ In the following cases, the Guarded
Channel
can be seen
without keying in the 1D number:
=When
you press RETURN
button
@
from a channel
which
has
been
selected
immediately
after
viewing
a
Guarded Channei
=When you press ANT/CABLE button @ froma channel of
a different broadcast mode (CHANNEL or CABLE} which
has been selected
immediately
after viewing a Guarded
Channel
=When you press CHANNEL
(-/+) buttons
@ on the Re-
mote Control or LEVEL/CHANNEL
(-/+) buttons @ on
the front panel, while in the MANUAL
PROGRAM
mode
of the INITIAL SET-UP {on MENU PAGE-3), if the select-
ed channel which has already been ADDed happens to also
be a Guarded Channel.
=When you press "4" (CHANNEL UP} or "5" (CHANNEL
DOWN) of the 10-Digit Keypad while in the MANUAL
PROGRAM
mode of. the INITIAL SET-UP, if the Guarded
Channel happens to also be the next higher or lower chan-
nel following the one to which you are presently tuned.
=While in the AUTO PROGRAM mode of the INITIAL SET-
UP, if the AUTO
PROGRAM
is interrupted immediately
when a Guarded Channel appears.
=When the channel! which has already been set for the ON
TIMER or HOME SITTER is set as a Guarded Channel.
®@ If you forget the ID number which you have set, reset it.
138 —
9. INITIAL SI
P
The INITIAL SET-UP feature allows you to perform basic set-
tings for the TV status. This consists of Channel Memory (Auto/
Manual), Message Style and Noise Mute.
Note: When
performing
Channel
Memory
(MANUAL
PRO-
GRAM},
select an appropriate
broadcast
mode
(either
"CHANNEL" or "CABLE") before you select the INITIAL
SET-UP mode.
With PAGE-3 (or PAGE-t or PAGE-2) MENU displayed on the
screen, press "9" of 10-Digit Keypad
® . The display will
show:
Press appropriate 10-digit key to select the item.
1) AUTO PROGRAM
This function allows memorizing the channels automatically to
match the TV broadcasts and cable channels of your area. The
memorized
channels
can be selected
by CHANNEL
(-/+)
buttons @ on the Remote Control or LEVEL/CHANNEL
{-/+)
buttons @ on the front panel, or in the CHANNEL
SCAN
mode, while skipping channels where there are no broadcasts.
Press "1" of the 10-Digit Keypad. The following display will
appear and the program set-up procedure begins automatically.
NOW
ress
CABLES OT
When tuned to a channel in which a TV program is broadcast,
the following display appears and this channel is memorized.
NOW
PROGRAMING !
im]
CABLE
02
When the AUTO PROGRAM procedure (scanning and memoriz-
ing) is completed, it will be indicated by the following display.
PROGRAMING
OVER #
Notes:
@ The AUTO
PROGRAM
procedure takes approximately 4
minutes,
If you wish to stop this procedure
before com-
pletion, press any button on the remote control.
2) MANUAL
PROGRAM
Similar to the AUTO PROGRAM function on the left, this is for
memotizing channels, but it is performed manually. The result-
ing Manual
Programing is also effective when performing up/
down channel selection.or CHANNEL SCAN.
Press ''2'. The display wil! show:
Sel)
Boune= 13,
The current tuned-in channel
Simply follow the on-screen instructions,
Note; First
select
the
broadcast
mode
before
entering
this
MANUAL
PROGRAM mode.
1) Press "1" (ADD) to add this channel in memory. A bar '~'"
will appear
between
the broadcast
mode
(CHANNEL
or
CABLE) and the channel number to. show that the channel
has been memorized.
2) Press 2' (ERASE) to erase this channel from memory, if
you do not wish to preset it in memory or if no TV station
is broadcasting on it. The bar between the broadcast mode
and channel number will disappear.
3) Press "4" (CHANNEL UP) or "5" (CHANNEL DOWN) to
select the next higher or lower channel.
4) Press "3" (END) when you have stored all required channels
in memory.
5) When you wish to store channels of the other broadcast
mode, select the mode first, then repeat steps 1) through 4}.
@
tn step 3) above, if selecting channels is difficult, press
the CHANNEL (-/+) buttons on the Remote Control.
©
Be sure to perform
these operations using the Remote
Control.
Continued on next page >
-19—
S092¢-AV
SOSZ2-AV
Advertisement
