Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HP 260 G1
Summary of Contents for HP 260 G1
- Page 1 Hardware Reference Guide HP 260 G1 DM Business PC...
- Page 2 HP End User License Not all features are available in all editions of Agreement (EULA). If you do not accept these The information contained herein is subject to Windows 8.
- Page 3 About This Book This guide provides basic information for upgrading the HP Desktop Mini Business PC. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
- Page 4 About This Book...
-
Page 5: Table Of Contents
Table of contents 1 Product features ............................1 Standard configuration features ........................... 1 Front panel components ............................2 Rear panel components ............................3 Serial number location ............................4 2 Hardware upgrades ............................5 Serviceability features ............................5 Warnings and cautions ............................5 Connecting the power cord ............................ - Page 6 Contacting support .............................. 29 Index ................................30...
-
Page 7: Product Features
Product features Standard configuration features Features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). NOTE: This computer model can be used in a tower orientation or a desktop orientation. The tower stand is sold separately. -
Page 8: Front Panel Components
Front panel components Drive configuration may vary by model. Dual-State Power Button Microphone Connector Hard Drive Activity Light Headphone Connector USB 3.0 Ports NOTE: The Power On Light is normally white when the power is on. If it is flashing red, there is a problem with the computer and it is displaying a diagnostic code. -
Page 9: Rear Panel Components
Rear panel components AC Power Cord Connector Line-Out Connector for powered audio devices (green) DisplayPort Monitor Connector USB 2.0 Ports (black) with keyboard wakeup function RJ-45 (network) Jack USB 3.0 Ports (blue) Power Cord Retainer Clip Cable lock slot VGA Monitor Connector (blue) Rear panel components... -
Page 10: Serial Number Location
Serial number location Each computer has a unique serial number and a product ID number that are located on the exterior of the computer. Keep these numbers available for use when contacting customer service for assistance. Chapter 1 Product features... -
Page 11: Hardware Upgrades
To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo. WARNING! Energized and moving parts inside. -
Page 12: Connecting The Power Cord
Connecting the power cord When connecting the power supply, it is important to follow the steps below to ensure the power cord does not pull free from the computer. Plug the female end of the power cord into the power supply brick (1). Connect the other end of the power cord to an electrical outlet (2). -
Page 13: Removing The Computer Access Panel
Removing the computer access panel To access internal components, you must remove the access panel: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as a USB flash drive, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices. - Page 14 Loosen the screw on the rear of the computer (1) then slide the panel forward and lift if off the computer (2). Chapter 2 Hardware upgrades...
-
Page 15: Replacing The Computer Access Panel
Replacing the computer access panel Place the panel on the computer then slide it back (1) and tighten the screw (2) to secure the panel in place. Turn the computer over. Insert screws into the two holes closest to the front of the computer (1) and tighten them. Insert rubber plugs into the two holes closest to the front of the computer (2). -
Page 16: Changing From Desktop To Tower Configuration
Orient the computer so that its right side is facing up and place the computer in the optional stand. NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional tower stand. Reconnect the power cord and any external devices, then turn on the computer. -
Page 17: Removing And Replacing A Hard Drive
Removing and replacing a hard drive NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as a USB flash drive, from the computer. - Page 18 Unplug the combined power and data cable from the hard drive. Transfer the silver and blue isolation mounting guide screws from the old hard drive to the new hard drive. Chapter 2 Hardware upgrades...
- Page 19 Hold the new hard drive over the bay and plug the combined power and data cable into the hard drive. Align the guide screws with the slots on the chassis drive cage, press the hard drive down into the bay, then slide it forward until it stops and locks in place.
-
Page 20: Installing Additional Memory
Installing additional memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3L-SDRAM) small outline dual inline memory modules (SODIMMs). SODIMMs The memory sockets on the system board can be populated with up to two industry-standard SODIMMs. These memory sockets are populated with at least one preinstalled SODIMM. -
Page 21: Populating Sodimm Sockets
Populating SODIMM sockets There are two SODIMM sockets on the system board, with one socket per channel. The sockets are labeled DIMM1 and DIMM2. The DIMM1 socket operates in memory channel B. The DIMM2 socket operates in memory channel A. Item Description System Board Label... -
Page 22: Installing Sodimms
Installing SODIMMs CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding or removing memory modules while voltage is present may cause irreparable damage to the memory modules or system board. - Page 23 To remove a SODIMM, press outward on the two latches on each side of the SODIMM (1) then pull the SODIMM out of the socket (2). Slide the new SODIMM into the socket at approximately a 30° angle (1) then press the SODIMM down (2) so that the latches lock it in place.
- Page 24 Align the memory door over the SODIMMs, lower the door, and then press the door into place. Replace the access panel. If the computer was on a stand, replace the stand. Reconnect the power cord and turn on the computer. Lock any security devices that were disengaged when the computer cover or access panel was removed.
-
Page 25: Replacing The Battery
The lithium battery is only used when the computer is NOT connected to AC power. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/recycle. - Page 26 Locate the battery and battery holder on the system board. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery. NOTE: You may need to use a small tool, such as tweezers or needle-nose pliers, to remove and replace the battery.
-
Page 27: Installing A Security Lock
Pull back on the clip (1) and slide the replacement battery down into the holder (2). CAUTION: Be sure the + symbol on the battery is facing the outer edge of the computer. NOTE: After the battery has been replaced, use the following steps to complete this procedure. Replace the computer access panel. -
Page 28: Padlock
VESA (Video Electronics Standards Association) standard, which provides industry-standard mounting interfaces for Flat Displays (FDs), such as flat-panel monitors, flat displays, and flat TVs. The HP Quick Release connects to the VESA-standard mounting points, allowing you to mount the computer in a variety of orientations. - Page 29 Using four 15 mm screws included in the mounting device kit, attach one side of the HP Quick Release to the computer as shown in the following illustration. Using four screws included in the mounting device kit, attach the other side of the HP Quick Release to the device to which you will mount the computer.
- Page 30 (2) on the device on which you want to mount the computer. An audible 'click' indicates a secure connection. When attached, the HP Quick Release automatically locks in position. You only need to slide the lever to one side to remove the computer.
-
Page 31: Supported Mounting Options
Supported mounting options The following illustrations demonstrate some of the supported mounting options for the mounting bracket. ● On the back of a flat panel monitor ● On a wall ● Under a desk, allowing at least 2.5 cm (1 in) clearance Mounting the computer... -
Page 32: Appendix A Electrostatic Discharge
Use conductive field service tools. ● Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding, contact an HP authorized dealer, reseller, or service provider. NOTE: For more information on static electricity, contact an HP authorized dealer, reseller, or service provider. -
Page 33: Appendix B Computer Operating Guidelines, Routine Care And Shipping Preparation
Computer operating guidelines, routine care and shipping preparation Computer operating guidelines and routine care Follow these guidelines to properly set up and care for the computer and monitor: ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ●... -
Page 34: Shipping Preparation
Shipping preparation Follow these suggestions when preparing to ship the computer: Back up the hard drive files to an external storage device. Be sure that the backup media is not exposed to electrical or magnetic impulses while stored or in transit. NOTE: The hard drive locks automatically when the system power is turned off. -
Page 35: Appendix C Accessibility
Supported assistive technologies HP products support a wide variety of operating system assistive technologies and can be configured to work with additional assistive technologies. Use the Search feature on your device to locate more information about assistive features. - Page 36 26 battery 19 computer access panel 7 hard drive 11 hard drive installation 11 removal 11 security HP Quick Release 22 cable lock 21 padlock 22 serial number location 4 installation guidelines 5 shipping preparation 28 installing SODIMMs, installing 16...