Advertisement
Step 3
"HOT MASK"
(It is recommended that you use "HOT MASK" once a day for milky lotion or once or twice
a week for sheet mask.)
Fine vibrations and gentle switching of the electrode enhance the effect of milky lotion or
sheet mask.
1 Place a sheet mask on your face or spread milky lotion or cream that you would
normally use over your entire face.
●
Wipe off any lotion on your hands.
2 After confirming that the power adaptor is connected to the main body, press the
power switch. (Fig.10)
●
"Low" on the level indicator lamp lights and "HOT MASK" on the mode indicator lamp
starts flashing. If a lamp in another mode is flashing, press the mode switch button
to switch to "HOT MASK."
When the "HOT MOISTURIZE" mode is finished, press the power switch and the
"HOT MASK" mode will automatically be set.
3 Choose "the strength" of electrical potential with the level switch button.
●
Switch the "strength" with the Level switch button according to the condition of your
skin.
●
Every time the level indicator button is pressed, the high, medium, and low of the
electrical potential will be switched. There will be no change in vibration strength.
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "Low."
4 Hold the device with your hand touching the back plate of the body. (Fig.5)
●
Make sure to hold the body with your hand touching the back plate.
5 Apply and move the heating head slowly. (Fig.6)
When using a sheet mask, slide the head over the sheet mask.
●
The mode indicator lamp will switch and turn on, and the device will start to vibrate.
The time for use is within 3 minutes.
●
CAUTION
Unless you apply the heating head to your skin while touching the back plate, the
device will not vibrate. (skin sensing function)
If the heating head is not vibrating, the device is not working.
If you leave the device as it is for about 3 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
Indicating timer function
Skin care time is indicated by the buzzer beeping about every 45 seconds as a guide.
[Example of skin care sequence]
Divide the area from your face to décolletage into four zones as shown in the
illustration. By moving the heating head in the order of ①②
④décolletage, the whole area can be efficiently and uniformly cared for.
Apply the heating head gently to the face and slowly move the device by sliding it
●
from the center of the face to the outer side.
Do not keep the heating head on the same area of skin, it is
necessary to move it around.
(Cause of problems with your skin or physical discomfort.)
③T-zone
-11-
●
Do not apply the device on the same area of skin for more than 10 seconds.
●
If you feel your skin tingling by micro current while using the device, press the Level
switch button and switch to "LOW."
6 After 3 minutes have elapsed, the device will automatically shut off. (Auto shutoff function)
●
The finish sound (beep beep) will inform you.
7 After use, make sure to pull out the power adaptor from the electric outlet and the main
body. (Fig.7)
●
To continue to use the next mode, do not disconnect the power adaptor.
8 Wipe off the lotion on the heating head and the body of the device with a tissue.
Step 4
"COOL"
n this mode, the cooling head surface that is cooled about 10℃ below the ambient
I
temperature tightens the pores of your skin.
Use this device at an ambient temperature from 10 to 40℃. (If you
use "
COOL
" mode at low temperature, the head may be overcooled,
damaging the skin.)
CAUTION
Continuous use of the "
COOL
" mode makes it difficult to cool the cooling head.
The warning sound (beep beep) and the flashing "
will inform you.
1 After confirming that the power adaptor is connected to the main body, press the power
switch. (Fig.11)
●
The level indicator lamp will go out, and "
flashing. If a lamp in another mode is flashing, press the mode switch button to
switch to "
COOL
."
When the " HOT MASK " mode is finished, press the power switch and the "
mode will automatically be set.
2 Wait until the cooling head has cooled.
●
Preparation for cooling takes about 10 seconds. "
flashes during preparation.
●
When the device is ready for use, the ready sound will beep, and the mode indicator
lamp will be turned on.
CAUTION
The device does not vibrate in "
COOL
3 Apply the cooling head gently to your skin and move it slowly just like patting your face.
(Fig.12)
●
The mode indicator lamp will change to lighting from flashing.
The cooling head does not vibrate.
●
The time for use is within one minute and 50 seconds.
●
Since you can apply the device to the same area of your skin for only one second,
repeatedly apply the head to your skin on and off towards the face.
●
There is no indicating timer function in the "COOL" mode.
CAUTION
●
Do not slide the cooling head over the skin.
●
Do not keep the cooling head in the same area of the skin, but move it around.
The cooling effect of the cooling head may be lessened.
COOL
" on the mode indicator lamp
COOL
" on the mode indicator lamp starts
COOL
" on the mode indicator lamp
COOL
" mode.
-12-
"
Advertisement
