Table of Contents
Advertisement
Quick Links
User Manual
Electric Vehicle Charger
Read the "Safety Precautions" before use to ensure safe operation.
After reading the user manual, store it in an accessible place for easy reference.
EVW011SK-SN
EVW011SK-SR
www.lg.com
*MFL72095901*
Copyright © 2023 LG Electronics Inc. All Rights Reserved.
(2312-REV01)
Printed in Korea
Advertisement
Table of Contents
Related Manuals for LG EVW011SK-SN
Summary of Contents for LG EVW011SK-SN
- Page 1 Read the “Safety Precautions” before use to ensure safe operation. After reading the user manual, store it in an accessible place for easy reference. EVW011SK-SN EVW011SK-SR www.lg.com *MFL72095901* Copyright © 2023 LG Electronics Inc. All Rights Reserved. (2312-REV01) Printed in Korea...
-
Page 2: Table Of Contents
. regulations are in place, and also provides product take- LG Electronics will also provide open source code to back & recycling service voluntarily in some regions. you on CD-ROM for a charge covering the cost of LG Electronics evaluates product’s recyclability at the... -
Page 3: Pre-Check Information
PRE-CHECK INFORMATION • The information provided in this document includes general descriptions or technical characteristics of the included product. • This document is not intended to be used or replaced for specific users who wish to determine the suitability or reliability of this product. -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING This manual contains important instructions for Models EVW011SK-SN, EVW011SK-SR that shall be followed during installation, operation and maintenance of the unit. Read all the instructions before using this product. This device should be supervised when used around children. - Page 5 INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR ELECTRIC SHOCK • To prevent the risk of fire or electric shock accidents, please read and follow these safety precautions and operating procedures carefully. • There is a risk of electric shock. Do not connect the electric vehicle and the charger before the inspection. Just turning off the charger does not reduce the risk.
- Page 6 CAUTION • Ensure the charger connector is free from water, humidity, or foreign substances. • Do not place the charger near flammable materials during use. Keep it away from carpets and cluttered workspaces. • Educate children to prevent them from playing with the device. •...
-
Page 7: Moving And Storage Instructions
MOVING AND STORAGE INSTRUCTIONS EVW011SK-SN, EVW011SK-SR For maximum performance, please read the following instructions. Storage Before installing and powering the charger, ensure that the product is stored in a clean and dry environment at a temperature of -40 °C to 70 °C (-40 °F to 158 °F). The charger must always be stored upright in a box during cargo loading. -
Page 8: Charger Specifications
CHARGER SPECIFICATIONS EVW011SK-SN Model EVW011SK-SR 226 mm x 503.2 mm x 165 mm Size (Width x Height x Depth) (8.89 inches x 19.8 inches x 6.49 inches) Weight 7.1 kg (15.6 lbs) Voltage Single Phase (208 / 240 V ± 10 %) AC Input Frequency 60 Hz Voltage Single Phase (208 / 240 V ± 10 %) -
Page 9: Accessories
ACCESSORIES Wall Mount Wall Mount Fixing Anchor Wall Mount Fixing Screw M4 O-ring Screw 1 piece 2 piece 2 piece 1 piece SEAL LABLE 2 piece... -
Page 10: Mechanical Characteristics
MECHANICAL CHARACTERISTICS Charger Size [Unit : mm (inches)] 226 (8.89) 165 (6.49) (2.3) -
Page 11: Charger Size
Charger Size [Unit : mm (inches)] 107.8 (4.2) 290 (11.4) 105.4 (4.1) Charger Appearance 7-dit 14 Segment RFID Card Reader Connector (AC 5-pin) Holder Cable Holder Speaker... -
Page 12: Installation Instructions
INSTALLATION INSTRUCTIONS • Do not expose the charger to rain, high temperatures, dust, corrosive gases, flammable Caution! substances, or explosive gases. Installation Location WARNING Risk of explosion. This equipment has arcing or sparking parts that should not be exposed to flammable vapors. This equipment should be located at least 460 mm (18.1 inches) above the floor. -
Page 13: Installation Process_Charger
Installation Process_Charger Use the enclosed fixing anchors and screws to hang the wall mount on the wall. - Check the wall material and thickness of the finishing materials. - The enclosed anchors and screws can be used when the wall material is non-cracking concrete, lightweight concrete, strong natural stone, soft natural stone, brick, and hollow block. - Page 14 Align the charger with the base frame and secure the charger. Open the main body of the charger and use the enclosed M4 O-ring screw to secure the body to the wall mount. Screw M4 O-ring Screw (Hole Cover)
- Page 15 Tighten Screw for Front and body enclosure to 6kgf*cm(5.2lbf*In). After completing installation, attach the SEAL LABLE as shown below. Attachment Location of SEAL LABLE NOTE Location Torque Screw for Front and body enclosure 5.2 lbf*In / 6 kgf*cm Screw (Hole Cover) 2.6 lbf*in / 3 kgf*cm...
-
Page 16: Wiring And Grounding
Wiring and Grounding Check that the breaker on the distribution panel is turned off. Detach the plastic cover on the terminal block. Insert the AC 208 / 240 V input cable through the power cable input at the bottom. Connect the AC 208 / 240 V input cable to the left power connection terminal and the internal panel GND terminal on the terminal block. - Page 17 NOTE • The AC input power cable is not included with the charger. • The cable specifications should be determined based on the distance between the distribution panel and the charger, according to the conditions of the installation work. • The disconnect switch should be installed inside the distribution panel of the installation location.
-
Page 18: Electrical Network Type
Electrical Network type Available Electrical network type Electrical network type Voltage Picture Split Phase 216 Vac ~ 264 Vac WYE Network 187 Vac ~ 228 Vac... -
Page 19: Operating Instructions
OPERATING INSTRUCTIONS To prevent electric shock, do not touch uninsulated parts of the connector or the internal terminals of the charger. Do not use the connector if there are damaged or corroded Caution! parts. Using a damaged or defective connector can lead to overheating or the risk of electric shock. -
Page 20: Charging Operation Procedure
Charging Operation Procedure Charging standby screen Authentication and payment Electric vehicle connector connection Ready for charging (Connector automatic lock on*) Start charging Stop charging (Connector automatic lock off*) Charging complete/stop Connector clean-up • *: The automatic lock/release of the connector is controlled by the vehicle (whether this is supported varies depending on the model of the vehicle) •... -
Page 21: Common Screen Configuration
Common Screen Configuration In the default standby screen, READY, software versions , charging rates, and total charging power are displayed at 5-second intervals. (The total charging power is displayed in kWh up to four decimal places over two screen displays. It can display up to 999999.9999 kWh. - Page 22 [Total Charging Power] • The current status of the charger is displayed through the status indicator LED and the strings displayed on 7-digit 14 Segment. • The status indicator LED displays colors like blue/green/red, and effects like blinking/flowing can be added for display. •...
-
Page 23: Charging Process
Charging Process To charge, proceed with authentication and connector connection. If you connect the connector after authentication a) Tag the membership card (RFID card). b) Connect the connector. - Page 24 If you authenticate after connecting the connector a) If you connect the connector on the standby screen, the screen switches to the membership card tag screen. b) If you tag a membership card (RFID card), the authentication process proceeds.
- Page 25 Proceed with charging. • During charging, the charged amount, charging speed, charging time, and charging fee are changed and displayed sequentially at 5-second intervals. • During charging, you can stop charging at any time by tagging your membership card. [Start charging] [Charged amount] [Charging speed] [Charging time]...
- Page 26 Charging ends upon a stop charging request, when fully charged, or after a predetermined time (14 hours) has elapsed. • After STOP is displayed for 5 seconds, charging information (charged amount, charging time, charging fee at 5-second intervals) and connector return guidance (PLUG, RETURN at 3-second intervals) are repeatedly displayed. •...
- Page 27 If the connector return is not completed when the charging information and connector return guidance are displayed after charging ends, the connector return guidance (PLUG, RETURN at 3-second intervals) is displayed for 18 seconds, and then it switches to the standby screen. (However, once the connector return is completed, it will immediately switch to the standby screen.)
- Page 28 Error Screen When a failure occurs during charging, during charging preparation, or in the standby state, the details of the failure are displayed and the charger attempts to recover automatically. (However, recovery is not attempted in a collision occurrence (error code 6701) situation.) Error Recovery Screen After displaying the error content, the automatic recovery screen is displayed for 15 seconds.
-
Page 29: Operation Stop (Availability Change) Screen
Operation Stop (Availability Change) Screen This is the screen displayed during a temporary stop in operation due to operation policy. Operation stop and resumption are possible through remote control of the charging control. Firmware Download Screen This is the screen displayed during firmware download via the firmware update command from the charging control. (This is only displayed under certain statuses, such as “charging possible”... -
Page 30: Setting Screen
Setting Screen This is the screen displayed when the charger settings app is connected to the charger. (The method to connect the charger settings app to the charger is shown in the settings guide document.) -
Page 31: Fault Codes
FAULT CODES WARNING This device provide an automatic reset feature. Error Codes Description Solution 1101 Input Overvoltage Detection Charger manufacturer confirmation needed 1102 Input Undervoltage Detection Charger manufacturer confirmation needed 1201 Input Overcurrent Detection Charger manufacturer confirmation needed 1203 AC Leakage Current Error Charger manufacturer confirmation needed 1204 DC Leakage Current Error... -
Page 32: Certification
CERTIFICATION CERTIFICATION Description FCC Compliance Statement (For USA) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. - Page 33 CERTIFICATION Description FCC Notice (For USA) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 34 CERTIFICATION Description Industry Canada Statement (For Canada) [For having wireless function (WLAN, Bluetooth,...)] This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
- Page 35 CERTIFICATION Description RSS-247 Requirement (For Canada) [For product having the wireless function using 5 GHz frequency bands] (1) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (2) For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p.
- Page 36 CERTIFICATION Description ENERGY STAR This product qualifies for ENERGY This product qualifies for ENERGY STAR®. STAR®. Changing the factory default configuration and settings or enabling certain optional Changing the factory default configuration and settings or features and functionalities may increase energy consumption beyond the limits required enabling certain optional features for ENERGY STAR®...
- Page 38 Supplier’s Declaration of Conformity Trade Name Responsible Party LG Electronics USA, Inc. Address 111 Sylvan Avenue, North Building, The model and serial number of the product are Englewood Cliffs, NJ 07632 located on the back and on one side of the product.