Whirlpool ADG 8683 Installation And Maintenance Instructions Manual

GB ADG 8683
Programme selector
On / Off Button
Start button
Switches "on" when the dishwasher is operating. Flashes when a
fault occurs. Switches off at the end of the programme.
START button RESET function:
Press this button for at least 2 seconds; the selected programme and
options are cancelled. Main failure displays (repeated flashing of the
START indicator lamp) can be cancelled by RESETTING. Detailed
instructions are given in chapter 5 "What to do, in the event of...".
Rinse aid level indicator and salt level indicator
These indicator lamps light up when rinse aid or salt need to be added.
Add just before starting a wash programme.
P
Programmes
1
Sensor Intensive 60-70°C
2
Sensor Normal
3
Pre-Rinse
4
Glasses
5
Rapid
6
2)
Bio
7
Antibacterial
1) Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g. different loads, options, different sensor
settings (only with sensor programmes), different water supply temperatures, as well as water hardness and power supply voltage.
2) Reference programme for energy label in compliance with EN 50242. - Important information for Test Laboratories: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: "nk_customer@whirlpool.com".
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Whirlpool is a registered trademark of Whirlpool USA
Before using the dishwasher, read the
installation and maintenance instructions carefully!
1. OVERVIEW
Table 1.1.
Programme chart
Available
options
Recommended programme for heavily soiled
crockery, with dried-on food, e.g. pots and pans.
Recommended programme for routine washes,
40-55°C
for crockery with no dried-on food (not for EN
50242).
cold
Crockery to be washed later.
Lightly soiled crockery, with no dried-on food,
40°C
e.g. glasses and cups.
40°C
Lightly soiled crockery, with no dried-on food.
50°C
Normally soiled crockery.
Normally - heavily soiled crockery, with
3) additional antibacterial wash. Programme
interruption (e.g. due to door opening) can
compromise elimination of germs.
Time and failure display
With normal operation, the display indicates residual time (h:mm),
while with the"Delayed start" function selected it indicates time
remaining until the start of the programme (hh).
If "F.." appears on the display, see chapter 5 "What to do, in the
event of...".
Delayed start button
The wash cycle can be programmed to start after 1- 24 hours.
With each successive touch of the button, the delayed start
indicator increases by one hour and after 24 returns to 00. Then
press the START button. The dishwasher will start at the set time.
HalfLoad/Multizone button
Load the upper or lower rack only.
press once = wash upper rack (the indicator light/symbol lights up)
press twice = wash the lower rack (the indicator light/symbol lights up)
press 3 times = Off (Half load/Multizone deactivated).
When washing without the top rack, press the "Half load"
(i.e. "lower rack wash") button twice. The indicator light/
corresponding symbol lights up.
Power Clean
Intensive wash with additional water jets and greater loading
flexibility in the bottom rack.
Detergent setting upon initial use and when using a different type of detergent
1. Select the third programme in the relative table.
2. Press the START button for approx. 7 sec. to change the display.
3. Using the START button, select the desired detergent:
Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action
detergents (in this way, the rinse aid and/or salt indicator is deactivated).
Display shows OFF = Powder detergent (factory setting).
(rinse aid level and salt level indicator activated).
4. Switch the appliance off and then switch it on again.
The selected detergent type will be indicated for approx. 3 sec..
Detergent
dispenser
Loading instructions large
1)
Consumption
small Litres kWh Minutes
X X 13-20 1.10-2.00 100-150 ±
X X 10-13 0.80-1.05 60-120 ±
— — 4,0 0,03 14 ±
X — 10,0 0,85 100 ±
X — 10,0 0,65 30 ±
X X 14,0 1,05 195 ±
X X 13,0 1,50 115 ±
5019 396 01063
1)
1)
1)
1)
1)
1)
1)
1