Remote Button Descriptions; Operating A Component; Specifications - Sony RM-V40A Operating Instructions Manual

4 Press the ENTER button.
The volume control setting is changed to
"Receiver /amplifier." You can control
the volume of the receiver (or amplifier)
of the AVI position while selecting any
component.
Notes
* If you are using more than one receiver (or amplifier) and have set
iton the CBL or AV2/DBS position, from those positions you
cannot control the volume of the receiver (or amplifier) of the AV1
position. >
+ If you change the setting of the AV1 position to a component other
than a receiver or amplifier, the volume control setting of video
components will return to "TV" even if you have changed the
factory preset volume control. In this case, you will not be able to
control the volume from audio components other than a receiver
or amplifier.
To reset to factory preset volume control
In step 3 above, press VOL- instead.
Operating a Component
1 Make sure that the slide switch is set to
the position that corresponds to your
desired component.
SAO
2 Point the Commander directly at the component.
3 Press the button for the function you want to use.
See "Remote Button Descriptions" for complete descriptions of the
buttons on the Commander.
Notes on Using the Remote Commander
Basically, use this Commander in the same way as the Commanders
supplied with your components.
¢ Using this Commander will not increase the functions of your
components. The functions of the Commander are limited to the
functions of the components themselves. For example, if your TV
does not have a MUTING function, the MUTING button on this
Commander will not function with your TV.
e Some functions of the component may not work with this
Commander.
¢ If your cable box can control volume, be sure to set its volume
switch to a medium position. If the volume on the cable box is
turned down completely, you will not be able to adjust your TV's
volume with the Commander.
Specifications
Operable distance Approx. 7 m (23 ft) (varies depending of the
component of each manufacturer)
Power requirements Two size AA (R6) batteries (not supplied)
Battery life Approx. 6 months (varies depending on frequency of
use)
Dimensions Approx. 60 x 207 x 41.5 mm (w/h/d)
Q'/2x8'/4x1"/w in.)
Mass Approx. 100 g (3.5 oz.) (not including batteries)
Supplied accessory Label (2)
Design and specifications are subject to change without notice.
Remote Button Descriptions
Operating a TV
To turn on and off.
To change the input mode.
To change the channel. For example, to
change to channel 5, press 0 and 5 (or press
5 and ENTER.)
To display the current channel on TV.
To call up the MENU display
To enter the selection.
To move the cursor to the left.
To move the cursor downward.
Volume up: +
Volume down: -
To operate the Picture-in-Picture function.
Pressing each button while pressing the PIP
button operates as the table below.
OU To mute the volume on the TV.
[12 To switch to TV operation. Set to the
position on which the TV is assigned. (TV,
AV1, AV2/DBS, or CBL)
13 To set up the Commander.
14 To operate SLEEP function on the TV.
(Works only for a TV with the SLEEP
function.)
[15 To change the channel. For example, to
change to channel 5, press 5 and ENTER.
[16] To move the cursor upward.
[17] To move the cursor to the right.
[18 Channel up: +
Channel down: —
(19 To operate JUMP, FLASHBACK or
CHANNEL RETURN function on the TV
depending on the setting of the TV's
manufacturer.
ON
a panela)
PIP operations
Press To
PIP and DISP Turn on/off the "window" picture.*
PIP and ENTER Turn off the "window" picture.
PIP and CH+ or CH- Change the TV channel in the "window" picture.
PIP and TV/VIDEO Change the input mode of the "window" picture.
PIP and 1 Move the location of the "window" picture.
PIP and 2 Swap the "main" picture and the "window" picture.
PIP and 3 Freeze the "window" picture.
* If the "window" picture does not turn off this way, try pressing ENTER while
pressing PIP.
Operating a VCR
To turn on and off.
To change the input mode.
To change the channel. For example, to
change to channel 5, press 0 and 5 (or,
press 5 and ENTER.)
To display the on-screen menu (Sony VCR
only).
To record, press » while pressing 0.
To play.
To rewind.
To pause.
To.stop.
To switch to VCR operation. Set to the
position on which the VCR is assigned.
(VCR, AV1, AV2/DBS, or CBL)
11| To set up the Commander.
[12 To change the channel. bor example, to
change to channel 5, press 5 and ENTER.
[13] To fast-forward.
[14] Channel up: +
Channel down: —
bt
ES
Elelel=eJaj