DeWalt DCR009 Original Instructions Manual page 17

Charging Procedure (Fig. A, B)
1. Pull the USB charging port cover
2. Insert the USB charging plug
3. Plug the USB charger plug
(such as on a computer or wall adapter).
nOTE: Charging takes two hours depending on power
supply rating (5V, 1A).
4. The charge indicator LED
or green and remain continuously ON while charging.
5. Charging is complete when the charge indicator LED
color is green or turns off.
6. The battery can be left charging or the USB charging cable
can be disconnnected.
7. Disconnect the charging cable and install the charging port
cover over the charging port.
Hot/Cold Delay
When the speaker detects that the battery is too hot or too cold,
it automatically starts a hot/cold delay, suspending charging
until the battery has reached an appropriate temperature. The
speaker then automatically switches to charging mode. This
feature ensures maximum battery life.
1. A cold battery may charge at a slower rate than a warm battery.
2. During a hot/cold delay the charge indicator LED
not illuminate. Charging will not activate until the battery
temperature reaches between 4 °C and 40 °C (40 °F and 104 °F).
3. Once the battery has reached an appropriate temperature,
the charge indicator LED
that the speaker has resumed the charging procedure.
Important Charging Notes
1. The speaker may become warm to the touch while
charging. This is a normal condition, and does not indicate
a problem. To facilitate the cooling of the speaker after use,
avoid placing the speaker in a warm environment such as in
a metal shed or an uninsulated trailer.
2. If the speaker does not charge properly, take the speaker
and USB cable to your local service center.
3. You may charge a partially used battery whenever you
desire with no adverse effect on the speaker.
Over Temperature Protection (Fig. A)
When over temperature protection is activated, the charge
indicator LED 12 will turn off.
nOTE: The unit can still be used during over the temperature
protection cycle.
Checking State of Charge (Fig. A)
• When the speaker is powered ON, press the power
button 1 and the speaker will tell you the percentage of
charge remaining in the battery.
nOTE: It does not indicate tool functionality and is subject
to variation based on product components, temperature
and end-user application.
11 away from the speaker.
10 into the charging port
9 into any USB charging port
12 color will be either red, yellow
12
12 will continuously blink, indicating
Charge Indicator LED Status
13 .
UnIT On
anD nOT
cHaRGInG
UnIT OFF anD
cHaRGInG
12
UnIT On anD
cHaRGInG
Package Contents
The package contains:
1 Speaker
1 Charging cable
1 Instruction manual
• Check for damage to the speaker, parts or accessories which
may have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
will
The following pictograms are shown on the tool:
Read instruction manual before use.
Waste electrical and electronic equipment:
Separate Collection.
Date Code Position (Fig. B)
The date code
is printed into the housing.
Example:
Description (Fig. A, B)

WARNING: Never modify the speaker or any part of it.
Damage or personal injury could result.
Power button
1
Volume up button
2
Volume down button
3
Bluetooth®** status indicator LED
4
Play/Pause button
5
Bluetooth®** button
6
Carry strap
7
USB charging cable
8
USB charger plug
9
USB charging plug
10
USB charging port cover
11
Charge indicator LED
12
LEVEL OF cHaRGE InDIcaTOR
cHaRGE LED cOLOR
≥40%
20% - 40%
Red and blinking.
≤20%
If 3% or less of charge remains, the speaker
will say "Battery low, please recharge."
0% - 99%
100% No illumination
0% - 99%
100%
14 , which also includes the year of manufacture,
2022 XX XX
Year and Week of Manufacture
EnGLIsH
Green
Yellow
Red
Red
Green
15