Advertisement
Operators and maintenance personnel shall be physically able to handle the bulk, weight and power of the tool.
9
Hold the tool correctly; be ready to counteract normal or sudden movements and have both hands available.
9
Maintain a balanced body position and secure footing.
9
Release the start-and-stop device in the case of an interruption of the energy supply.
9
Use only lubricants recommended by the manufacturer.
9
DO NOT use in confined spaces and beware of crushing hands between tool and workpiece, especially when unscrewing.
8
For multiple hazards, read and understand the safety instructions before installing, operating, repairing, maintaining, changing
9
accessories on, or working with the tool. Failure to do so can result in serious bodily injury.
Only qualified and trained operators should install, adjust or use the tool.
9
DO NOT modify this assembly power tool for threaded fasteners. Modifications can reduce the effectiveness of safety measures and
8
increase the risks to the operator.
DO NOT discard the safety instructions; give them to the operator.
8
DO NOT use the tool for threaded fasteners if it has been damaged.
8
Tools shall be inspected periodically to verify that the markings are legibly marked on the tool.
9
The user shall contact the manufacturer to obtain replacement marking labels when necessary.
9
2. INTRODUCTION
Fits most passenger and light commercial diesel injectors including Delphi, Denso, and Siemens.
Uses vibration and pneumatic force to easily remove seized injectors. The set includes a pneumatic diesel injector puller, adaptors, an air hose
and a control valve with a 1/4" BSP connector. Maximum air supply 116psi (8 bar). Storage case supplied.
3. SPECIFICATION
Model: ....................................................................... VS2080
Contents: ..............................................................................
Pneumatic diesel injector puller, Hose with control valve.
Adaptors: 9mm M25x0.5. 10mm M17x1.0, M18x0.75, M20x1.0,
M27x0.75, M27x1.0(x2). 11mm M29x1.0. 13mm M25x1.0.
14mm M8x1.0, M8x1.25, M10x1.5 15mm M20x1.5, M22x1.5,
M26x0.75, M31x0.75. 18mm M12x1.5, M14x1.5, M16x1.5, M18x1.5.
4. OPERATION
4.1.
Select and mount the appropriate connector to the injector
concerned (internally or externally threaded).
NOTE: Tighten the connector to between 20 and 30 Nm.
4.2.
Screw the vibration unit carefully onto the connector.
4.3.
With the pneumatic supply set to between 5 and 8 bar, connect
the air line to vibration unit ensuring that the control
valve is set to the closed position.
NOTE: The air line should provide only clean dry air or the
unit may become damaged.
4.4.
Open the control valve slowly to commence vibration and
open it further or close it to adjust the rate of vibration.
4.5.
When the injector is loose, shut off the air supply and carefully
lift out the assembled unit.
4.6.
Disassemble the unit and clean off the component parts using a
clean and soft cloth.
4.7.
Prior to replacing the unit in the case and after approximately
8 hours usage, place no more than 1ml of oil into the air inlet
in order to prevent the units' internals becoming wet and rusted.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
© Jack Sealey Limited
01284 757500
sales@sealey.co.uk
Original Language Version
fig.1
www.sealey.co.uk
VS2080
REGISTER YOUR
PURCHASE HERE
Issue 1
16/10/2023
Advertisement
