Sealey W1200T.V3 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
BEFORE OPERATION
Before operating, adjusting
or servicing the machine,
it is important that each
operator carefully reads the
operating instructions.
DURING OPERATION
Danger from unsecured
load. The operator must
ensure that wheels to be
carried by the machine are
correctly loaded and
supported in accordance
with the operating
instructions.
At least two people are required to assemble the trolley.

Ensure that the vehicle to be worked on is safely supported on axle stands.

Ensure that the trolley is in sound condition and good working order before use.

Keep trolley clean for best and safest performance.

Only use the trolley on fi rm, level, unobstructed surface which is capable of supporting the trolley and wheel.

Ensure there is no risk of pinching in between moving parts.

Ensure work area has adequate lighting.

Keep work area clean and tidy and free from unrelated materials.

Keep children and unauthorised persons away from the work area.

Ensure all non essential personnel keep a safe distance when the trolley is in use.

DO NOT overload the trolley - maximum capacity is 1500kg.

DO NOT allow untrained persons to operate the trolley.

DO NOT allow anyone to ride on the trolley.

DO NOT use on tarmacadam as it may sink under load.

DO NOT drive the unit over edges, rough surfaces etc. when loaded, as the whole unit may overturn.

DO NOT use trolley for purposes other than for which it is designed.

DO NOT operate the trolley when you are tired or under the infl uence of alcohol, drugs or intoxicating medication.

DO NOT make any alterations to this device.

Always stand and operate the wheel trolley from behind Upright Tube (4), see fi g.1. Always move the Wheel Trolley using one

Handle (20) in the socket on the left hand side (as viewed in the fi g.1 position) and the other Handle (19) in the Socket above
Lowering Pedal (A), see fi g.2.
Push the wheel as far onto the rollers as possible.

Ensure that the load can not tilt whilst lowering or moving.

Lower the wheel and secure it with the wheel support before transporting.

It is of the greatest importance for safety that the wheel trolley is secured by the locking mechanism on the nearest hole before

manoeuvring the unit. If the lock is not used, the wheel trolley could come apart while carrying the load and the wheel could tip out.
Maintain correct balance and footing when moving trolley and ensure that the fl oor is not slippery.

Wear suitable clothing to avoid snagging. DO NOT wear loose jewellery and tie back long hair. A full range of personal safety

equipment is available from Sealey.
Replace or repair damaged parts. Use only recommended parts. Unauthorised parts may be dangerous and will invalidate the

warranty.
Use a competent person to lubricate and maintain the trolley. DO NOT use brake fl uid to top up hydraulic unit. Use approved

hydraulic oil only.
When not in use store trolley, fully lowered, in a safe, dry, childproof area.

WARNING! Failure to comply with these instructions may result in loss of load, damage to trolley or other property and/or personal
‰
injury.
2. INTRODUCTION
Eight adjustable rollers (4 each side) allow for easy turning of large deep tread tyres. Extra large jacking handle and hydraulic foot
pedal allows for one man operation. Safety bar with composite guard goes around wheel to ensure stability during transportation.
© Jack Sealey Limited
WHEEL REMOVAL TROLLEY 1500KG CAPACITY
W1200T.V3
MODEL NO:
DURING OPERATION
Always use the locking
mechanism which locks
the lifting rollers in position
before manoeuvring the
loaded wheel changer.
DURING OPERATION
Potential slip/fall hazard.
Never stand or ride on the
wheel changer when
working with the machine.
Original Language Version
W1200T.V3 Issue 2 (H,5,F) 16/08/23