TABLE OF CONTENTS PRECAUTION / 预防措施 ........1-7 SPECIFIC SERVICE INSTRUCTIONS / 具体的维修说明...
Page 3
JVCKENWOOD Corporation reserves the right to make changes to any products herein at any time for improvement purposes. Firmware Copyrights The title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVCKENWOOD Corporation. Any modifying, reverse engineering, copy, reproducing or disclosing on an Internet website of the firmware is strictly prohibited without prior written consent of JVCKENWOOD Corporation.
Page 4
SPECIFICATION TIA measurement compliant GENERAL Frequency Range 450 ~ 520 MHz 400 ~ 470 MHz Channel Capacity Channel Spacing Analog 12.5 / 25 *1 kHz Digital 6.25 / 12.5 kHz PLL Channel Step 3.125 / 5 / 6.25 kHz Frequency Stability ±...
Page 5
EN measurement compliant (E2 type only) GENERAL Frequency Range 400 ~ 470 MHz Channel Capacity Channel Spacing Analog 12.5 / 20 / 25 kHz Digital 6.25 / 12.5 kHz PLL Channel Step 3.125 / 5 / 6.25 kHz Frequency Stability ±...
SECTION 1 PRECAUTION / 预防措施 This service manual does not describe PRECAUTION. SECTION 2 SPECIFIC SERVICE INSTRUCTIONS / 具体的维修说明 REALIGNMENT 2.1.1 Modes e.g. Reading FPU data: Keeps the user mode Writing FPU data: Gets out from the user mode User mode PC test mode: Gets in Test Mode with "Test Mode”...
2.1.4 Firmware Programming Mode · IP settings: (Refer to 2.1.3.4 Programming software KPG-D7 description) 2.1.4.1 Preface · Log in user: admin The repeater uses flash memory to allow it to be easily upgraded · Log in password: (blank) when new features are released in the future. The password setting is required for the first access.
INSTALLATION 2.3.1 Rack mounting for one repeater (1) Assemble two types of brackets with handles. <1> <2> (2) Attach two types of brackets with handles to the repeater. <3> <4> (3) The bracket long / short can be attached by swapping the left and right. Accessories for installation <4>...
(3) Connect repeaters A and B with reinforcing HW and fix them with screws. <4> (4) Attach two sets of brackets with handles to repeaters A and B. <5> <6> Screw hole for rail mounting M4 x 8 mm <5> <4>...
Page 12
2.4.2 Adding the RSSI or Reset Terminal on the CONTROL I/O (D-SUB 25-pin) Connector The configuration for pin 1 of the CONTROL I/O (D-SUB 25-pin) connector can be changed to allow it to supply the power source for RSSI. Follow the procedure shown below to change the configuration. Case 1: Add the RSSI.
2.5.1 Overview The NXR-1800 is a UHF Analog FM & Digital repeater operating in the 400~470MHz (E2 type), or 450~520MHz (E type) range. Transmit RF power range is 1W to 40W adjustable. The unit consists of receiver circuit, transmitter circuit, phase-locked loop (PLL) frequency synthesizer circuit, digital and audio control circuit, display circuit, and power supply circuit.
Page 14
2.5.3 Receiver System 2.5.3.1 RF circuit The receive signal from RX ANT is amplified by a RF amplifier (LNA: IC703) and passes through the variable capacitor tuned band- pass filters (BPF) to attenuate unwanted signals. The signal passing the band-pass filters (BPF) is heterodyned by the first mixer (RX 1st MIX: IC702) with the first local oscillator signal from the RX PLL frequency synthesizer circuit to produce a 45.00 MHz first intermediate frequency signal (first IF signal).
Page 15
2.5.4.4 CM Coupler circuit CM coupler circuit is a line for detecting forward wave and reflected wave. Forward wave is detected by IC3027 and is converted into DC voltage. If an abnormal antenna load is connected, reflected wave is detected by D3081 and converted into DC voltage. 2.5.4.5 Filter circuit This circuit is removes harmonics from the transmitter output and sends filtered signal to the antenna.
Page 16
2.5.5.3 TX VCO/ TX PLL 2.5.5.3.1 VCO circuit TX VCO consists of two VCOs, TX_L VCO and TX_H VCO. TX_L VCO and TX_H VCO are switched by DC switches (DC SW: Q2008 and Q2009), according to the operating frequency. TX VCO generates the carrier for the transmitter and the frequency range is 400 to 470MHz (E2 type), or 450 to 520MHz (E type). TX_L VCO (Q2003) oscillation frequency range is 400 to 435MHz (E2 type), or 450 to 485MHz (E type), and TX_H VCO (Q2007) is 435 to 470MHz (E2 type), or 485 to 520MHz (E type).
Page 17
2.5.6 Control Circuit The control circuit mainly consists of MPU/DSP (IC33) and FPGA (IC60) and their peripheral circuits. Furthermore, IC33 is composed of an ARM processor based on ARM Cortex-A15 and a DSP based on C66x. Their main tasks are as follows. (1) The MPU manages the operation of the Repeater and the external interface.
Page 18
2.5.6.1 MPU/DSP 2.5.6.1.1 The MPU/DSP (IC33) consist of ARM Cortex-A15 RISC processor and floating-point VLIM DSP, and equipped with peripheral function. This MPU operates at 1.4GHz clock and power supply voltage is controlled by the power management IC (PWR MNG: IC1). The MPU/DSP controls the flash memory, DDR3, eMMC, FPGA, and various control circuits.
Page 19
2.5.6.5 ADC, DAC circuit The ADC/DAC circuit consists of an ADC (IC76) and DAC (IC77 and IC78). The ADC/DAC performs the following processes: DAC: Conversion of various RF control voltages from digital to analog. ADC: Conversion of power supply voltage and various temperatures from analog to digital. 2.5.6.6 This repeater is equipped with a 100Base-TX or 10Base-T LAN interface.
Page 20
Furthermore, 3.3V output is also supplied to the following control system blocks. · Power management IC (PWR MNG: IC1) for MPU/DSP (IC33) · Terminal power supply for DDR3 (DDR3 TERM AVR: IC301) · FPGA (IC65) · ADC (IC76) etc. And the 5V output of 3.3V, 5.0V DC/DC (IC4000) is supplied to the following circuits. ·...
Page 21
[+B] 13.2V FINAL AMP (Q3069) (W3000) 9.0V AVR FAN (CN3005) (IC3022) [PLD_FAN] [PLD_FAN] H:2.0V L:0.8V [7.5V] 8.8V DC/DC 7.5V AVR DRV AMP (Q3065) (IC4100) (IC3030) PRE DRV AMP2 (Q3067) / APC BLOCK [5V_TX_EN] [5V_2] 5.0V AVR PA CTL (IC3027) / TX PLL (IC2000) (IC3029) DC SW PRE DRV AMP (IC3023)
COMPONENTS DESCRIPTION Part Ref. No. Use / Function TX-RX UNIT (XC1-329E-XX) Name IC902 DC AMP (TV tune) [DC AMP] Part Ref. No. Use / Function Name IC903,904 Buffer AMP(10MHz External reference) [BUFF AMP] Power Management [PWR MNG] IC1000 DC AMP(CV_TX_RX) [DC AMP] Voltage control [V CTL] IC1001 RX PLL...
Page 23
Part Part Ref. No. Use / Function Ref. No. Use / Function Name Name Q904 10MHz SW Q4018 DC SW (PLD_PS_SWT_CTRL) [DC SW] Q905,906 DC SW Q4020 DC SW (BASW) [DC SW] Q907 TRANS 10MHz AMP ISTOR Q4021,4022 DIGI DC SW TRANS Q1000 DC SW...
Page 24
Part Part Ref. No. Use / Function Ref. No. Use / Function Name Name D606-610 SURGE Surge protection [SRG PRTCT] D1008 VARI RX_H VCO assist tuning ABSOR [RX_H VCO ASST TUN] DIODE D700 VARI IF CLK VCO frequency control D1009 DIODE DC SW [IF CLK VCO F CTL] D1010-1011 VARI...
Part Ref. No. Use / Function Name Function Name D40044005 ZENER Over voltage protection O Power supply for logic DIODE [OVR V PRTCT] O Chip select D4007 ZENER Over voltage protection RESn O Power reset for controller and driver DIODE [OVR V PRTCT] D/Cn O Data/Command control...
Page 26
Rating and Condition Modifi I/O Signal Type Function Note Name cation Parameter Unit Analog TX Signal - 100Base-TX Conform to IEEE802.3 +Vout@100 0.95 1.05 -Vout@100 -1.05 -0.95 MLT-3 (4B/5B Encoding) Data rate 125.0 Mbps (100Base-TX) 10Base-T Vout@100 100Base-TX =125Mbps*4/5 Data rate (10Base-T) 10.0 Mbps Impedance...
Page 27
Rating and Condition Modifi I/O Signal Type Function Note Name cation Parameter Unit I/O Analog USB Data High-speed Plus -10.0 10.0 Baud Rate Mbps Low-/Full-speed Conform to Universal Serial Baud Rate Mbps (Low-speed) Specification Baud Rate Mbps (Revision 2.0 April (Full-speed) 27, 2000) USB GND...
Page 28
Rating and Condition Modifi I/O Signal Type Function Note Name cation Parameter Unit Analog TX Audio Input 1kHz/60%Dev. mVrms NFW (Voice) Input Max =2.0Vrms Input Impedance 600 PD to GND Analog RX Data Output Output Voltage mVrms Allowable Load (Signaling) Not /60%Dev.
Page 29
Rating and Condition Modifi I/O Signal Type Function Note Name cation Parameter Unit Digital Programmable 0.7*V 47k PU to VCC Function I/O3 5V+/-3% Input Impedance VOH(IO=0mA) Open Drain 47k PU to VCC VOL(IO=0mA) 5V+/-3% Digital Programmable 0.7*V 47k PU to VCC Function I/O4 5V+/-3% ...
2.13 元件说明 Part Ref. No. Use / Function 收发单元 (XC1-329E-XX) Name IC902 DC AMP (TV tune) [DC AMP] Part Ref. No. Use / Function Name IC903,904 Buffer AMP(10MHz External reference) [BUFF AMP] Power Management [PWR MNG] IC1000 DC AMP(CV_TX_RX) [DC AMP] Voltage control [V CTL] IC1001 RX PLL...
Page 43
Part Part Ref. No. Use / Function Ref. No. Use / Function Name Name Q904 10MHz SW Q4018 DC SW (PLD_PS_SWT_CTRL) [DC SW] Q905,906 DC SW Q4020 DC SW (BASW) [DC SW] Q907 TRANS 10MHz AMP ISTOR Q4021,4022 DIGI DC SW TRANS Q1000 DC SW...
Page 44
Part Part Ref. No. Use / Function Ref. No. Use / Function Name Name D606-610 SURGE Surge protection [SRG PRTCT] D1008 VARI RX_H VCO assist tuning ABSOR [RX_H VCO ASST TUN] DIODE D700 VARI IF CLK VCO frequency control D1009 DIODE DC SW [IF CLK VCO F CTL] D1010-1011 VARI...
Part Ref. No. Use / Function Name Function Name D40044005 ZENER Over voltage protection O Power supply for logic DIODE [OVR V PRTCT] O Chip select D4007 ZENER Over voltage protection RESn O Power reset for controller and driver DIODE [OVR V PRTCT] D/Cn O Data/Command control...
Page 46
Rating and Condition Modifi I/O Signal Type Function Note Name cation Parameter Unit Analog TX Signal - 100Base-TX Conform to IEEE802.3 +Vout@100 0.95 1.05 -Vout@100 -1.05 -0.95 MLT-3 (4B/5B Encoding) Data rate 125.0 Mbps (100Base-TX) 10Base-T Vout@100 100Base-TX =125Mbps*4/5 Data rate (10Base-T) 10.0 Mbps Impedance...
Page 47
Rating and Condition Modifi I/O Signal Type Function Note Name cation Parameter Unit I/O Analog USB Data High-speed Plus -10.0 10.0 Baud Rate Mbps Low-/Full-speed Conform to Universal Serial Baud Rate Mbps (Low-speed) Specification Baud Rate Mbps (Revision 2.0 April (Full-speed) 27, 2000) USB GND...
Page 48
Rating and Condition Modifi I/O Signal Type Function Note Name cation Parameter Unit Analog TX Audio Input 1kHz/60%Dev. mVrms NFW (Voice) Input Max =2.0Vrms Input Impedance 600 PD to GND Analog RX Data Output Output Voltage mVrms Allowable Load (Signaling) Not /60%Dev.
Page 49
Rating and Condition Modifi I/O Signal Type Function Note Name cation Parameter Unit Digital Programmable 0.7*V 47k PU to VCC Function I/O3 5V+/-3% Input Impedance VOH(IO=0mA) Open Drain 47k PU to VCC VOL(IO=0mA) 5V+/-3% Digital Programmable 0.7*V 47k PU to VCC Function I/O4 5V+/-3% ...
SECTION 3 DISASSEMBLY / 拆卸 Precautions for Disassembly (4) Remove the solder connecting the two receptacles and TX- RX UNIT. <5> 3.1.1 TX-RX UNIT disassembly procedure (5) Disconnect the fan motor wire from the TX-RX UNIT (1) Remove the 12 screws on the top of the repeater and CN3005.
3.1.2 LCD ASSY disassembly procedure (2) Pass the FPC of LCD ASSY through the hole in the (1) While pushing the hook part of MOUNTING in the direction MOUNTING and then attach it to the MOUNTING. <2> <3> of the arrow, remove the MOUNTING as shown in the figure.
3.2.3 Forming of the fan motor wire 3.2.4 Attaching the top plate (1) Attach the fan motor to the chassis and insert its connector Note: into the CN3005 housing. Make sure the fan motor wire fits in the grooves of the chassis.
SECTION 4 ADJUSTMENT / 调整 Test Equipment Required for Alignment Test Equipment Major Specifications 1. Standard Signal Frequency Range 400 to 520MHz Generator (SSG) Modulation Frequency modulation and external modulation Output -127dBm/0.1uV to greater than -20dBm/22.4mV When performing the Frequency adjustment, the following accuracy is necessary. ...
Test Pin of CONTROL I/O (D-SUB 25-pin) Connector Common Section Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 1) DC voltage: 13.2V Setting Audio 2) SSG standard modulation Analyzer Narrow Oscilloscope MOD: 1kHz, DEV: 1.5kHz Wide 5k MOD: 1kHz, DEV: 3kHz Wide 4k (E2 type only)
Page 58
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 1) Test Channel: Channel 1 Press [Start] button of "IF20” value = Within Frequency "Auto Tuning”. Press 0±12 digits. The value 2) Adj item: [Apply] button to store of "IF20”...
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 7. RD 1) Test Channel: Channel 1 Change the adjustment 80mVrms±5mV Level Audio value to become (Analog 2) Adj item: Analyzer 80mVrms within the Press [Apply] button to Narrow) [RD Level (Analog Narrow)] Oscilloscope...
Page 60
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 2.Low 1) Adj item: Power Write Fixed value for No Specification. No Transmit [Low Transmit Power Limit] meter each adjustment point as need to measure the Power Ammeter follows.
Page 61
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 6. Low RF 1) Test Channel: Channel 1 Power Change the adjustment 0.3W±0.1W Power meter value to become 0.3W Down 2) Adj item: Ammeter within the specified Press [Apply] button Detection [Low RF Power Down...
Page 62
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 1) Adj item: Deviation Write Reference value for [Analog Narrow] Maximum [Maximum Deviation (Analog meter each adjustment point as 2.1kHz±0.05kHz Deviation Narrow)] Oscilloscope follows. (Analog) [Maximum Deviation (Analog [Analog Wide 5k] Wide 5k)]...
Page 63
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 1) Adj item: Deviation Write Reference value for [DMR] Maximum [Maximum Deviation (DMR)] meter each adjustment point. ±2611~±2887Hz Deviation Oscilloscope (±2749Hz±5%) (DMR) 2) Adj item: Reference Value: [L1], [L3], [L5], [C1], [C3], [C5], [Maximum Deviation...
Page 64
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 1) Adj item: Deviation Write Reference value for [NXDN Very Narrow] Maximum [Maximum Deviation (NXDN meter each adjustment point. ±1203~±1471Hz Deviation Very Narrow)] Oscilloscope (±1337Hz±10%) (NXDN Reference Value: Very...
Page 65
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 13.TD 1) Adj item: Deviation Write Reference value for [Analog Narrow] Deviation [TD Deviation (Analog Narrow)] meter each adjustment point as 750Hz±50Hz (Analog) [TD Deviation (Analog Wide 5k)] Oscilloscope follows.
Page 66
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 14.TA 1) Adj item: Deviation Write Reference value for [Analog Narrow] Deviation [TA Deviation (Analog Narrow)] meter each adjustment point as 1500Hz±50Hz (Analog) [TA Deviation (Analog Wide 5k)] Oscilloscope follows.
Page 67
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 15. QT 1) Adj item: Deviation Write Reference value for [Analog Narrow] Deviation [QT Deviation (Analog Narrow)] meter each adjustment point as 350Hz±50Hz (Analog) [QT Deviation (Analog Wide 5k)] Oscilloscope follows.
Page 68
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 16. DQT 1) Adj item: Deviation Write Reference value for [Analog Narrow] Deviation [DQT Deviation (Analog meter each adjustment point as 350Hz±50Hz (Analog) Narrow)] Oscilloscope follows.
Page 69
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 17. Test 1) Adj item: Deviation Write Reference value for [Analog Narrow] Tone [Test Tone Deviation (Analog meter each adjustment point as 1500Hz±50Hz Deviation Narrow)] Oscilloscope follows.
Page 70
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 1)Adj item: Deviation Write Reference value for [Analog Narrow] Courtesy [Courtesy Tone Deviation meter each adjustment point as 500Hz±50Hz Tone (Analog Narrow)] Oscilloscope follows. [Analog Wide 5k] Deviation [Courtesy Tone Deviation 1000Hz±50Hz...
Page 71
Measurement Adjustment Specifications/ Item PC tuning mode Test- Termi Remarks Unit Unit Parts Method equipment 1)Adj item: Deviation Write Reference value for [Analog Narrow] Repeater [Repeater Gain (Analog meter each adjustment point as [Analog Wide 5k] Gain Narrow)] Oscilloscope follows. [Analog Wide 4k] (Analog) [Repeater Gain (Analog Wide...
Page 72
4.6.1 Necessary Deviation adjustment item for each signaling and mode The following shows the necessary adjustment items for each signaling deviation. Please read the following table like the following example. In the case of the signaling "QT (Wide 5k)”, this signaling is composed of three elements [Balance, Maximum Deviation, and QT Deviation (Wide 5k)].
Receiver Section Measurement Adjustment Specifications Item PC tuning mode Test- /Remarks Unit Terminal Unit Parts Method equipment 1. AF level Test Channel RX ANT Follow RA output level Follow RA setting Channel: 1 Audio adjustment at “8. RA output level Test Signaling Analyzer Level (Analog Narrow)”...
Page 74
Measurement Adjustment Specifications Item PC tuning mode Test- /Remarks Unit Terminal Unit Parts Method equipment 7. Open 1) Adj item: [Open Squelch RX ANT After input signal from Squelch (NXDN Very Narrow)] Audio SSG, press [Apply] adjust Analyzer button to store the [NXDN 2) Adj item: Oscilloscope...
Page 75
Measurement Adjustment Specifications Item PC tuning mode Test- /Remarks Unit Terminal Unit Parts Method equipment 13. High 1) Adj item: [High RSSI (Analog RX ANT After input signal from RSSI Narrow)] SSG, press [Apply] button to store the 2) Adj item: RA (D- adjustment value.
SECTION 5 TROUBLESHOOTING / 故障排除 Fault diagnosis of the BGA (Ball Grid Array) IC Overview When the IC treated as Non-replaceable parts (e.g., BGA IC part) seems to be problematic, there is no way to recover/repair it and need to proceed the unit replacement. Before proceeding the unit replacement, the following flowchart may help you to judge it. It may be effective to try it in the following case as example, but please note that the work reliability is required because the parts need to be removed and remount during this troubleshooting.
Page 92
Pass ● Checking power supply voltage (Fourth) Checking voltage Normal voltage Fail When all power supply voltage outputs are 0V, check the VDD_MPU 0.85 ~ 1.25V voltage of R22 on the IC3 (pin 1, /RESET) line. 1.15V_SMPS2 1.11 ~ 1.2V 3.3V: This voltage is normal.
Pass ● Checking the OLED control (Third) Fail Checking the communication Normal voltage The MPU/DSP may be broken. waveform SPI3_SCLK R162 Amplitude 3.3V Pass It is unlikely that the BGA broken is the cause of the trouble when the repeater can't be powered on. ■...
Page 94
Error Information Error Event / Assumed Condition / Measures Web Tool Item Name OLED Display (Error Code) E102 HSB LAN Error Hot Standby LAN The LAN connection between the Main and Sub repeaters under Hot Standby Connection Error fails. This error will be displayed when the following cases. Case1.
The MAC address number is on a sticker which is applied to the Chassis. It can't be rewritten number. This table shows an example of the NXR-1800 E2 type. The model name for the Service TX-RX UNIT (XCA-096E -** S) is NXR-1800S1. XXX-XXXX-XXX 5.3.5 After Changing the PCB...
Page 101
PRECAUTIONS ON SCHEMATIC DIAGRAMS * Due to the improvement in performance, some part numbers shown in the circuit diagrams may not agree with those indicated in the Parts List. * The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for reference only.
Page 105
BLOCK DIAGRAM TX-RX UNIT (XC1-329) *F1 (E type) F2 (E2 type) TEMP THP3 V3_3D_LAN DC SW 3.3V IC52 IC33 IC60 PA_CUR TX F QSPI1_CS0 F1:450~520MHz VG_DIS IN AMP QSPI1_D [3:0] V3_3D Q2002 F2:400~470MHz DC SW TEMP CURR DET THP2 FLASH QSPI1_SCLK 3.3V LNA_ON...
Page 106
SCHEMATIC DIAGRAM/原理图 TX-RX UNIT/收发单元 (XC1-329E-00 (NXR-1800 E2 type), XC1-329E-01 (NXR-1800 E type)) (1/2) VOLTAGE REGULATOR (TX PRE-DRIVE 3.3V) L2050 L2051 R2089 R3300 CN3017 CN3018 L3302 4.6V L2004 L2011 LNA_ON 7.5V TX Fin AMP FINAL POWER AMP DC SW R3160 L3300...
Page 107
TX-RX UNIT/收发单元 (XC1-329E-00 (NXR-1800 E2 type), XC1-329E-01 (NXR-1800 E type)) (2/2) 3.3V DC SW V3_3D_LAN DESTINATION LIST XC1-329E-00 XC1-329E-01 3.3V VOLTAGE CONTROL *F1 (E TYPE) 470p (F2:400-470M) (F1:450-520M) F2 (E2 TYPE) CN16 E23-1330-05 3.3V RAF040P01 CN18 E23-1330-05 ANoDE CN19 E23-1330-05...
Page 108
PARTS LIST [NXR-1800] * SAFETY PRECAUTION Parts identified by the symbol are critical for safety. Replace only with specified part numbers. * BEWARE OF BOGUS PARTS Parts that do not meet specifications may cause trouble in regard to safety and performance.
Page 109
Exploded view of general assembly and parts list 总装分解图及零件表 Block No.M1MM TX-RX UNIT<01> E2 type only 3-2(No.RA094<Rev.002>)
Page 110
General assembly / 本体总装 Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local --------- CHASSIS A4A-0059-00 BOTTOM PLATE A5C-0123-20 TOP PLATE A6C-0154-10 PANEL ASSY FRONT Note 1/ 注意 1 B1A-0130-00 FRONT GLASS OLED/WITH ADHESIVE B3H-0149-00 LCD ASSY OLED Note 1/ 注意...
Page 111
Electrical parts list / 电气零件表 TX-RX UNIT / 收发单元 Symbol Part No. Part Name Description Local type XC1-329E-00 (NXR-1800 E2 type IC701 --------- MOS IC Note 2/ 注意 2 XC1-329E-01 (NXR-1800 E IC702 --------- MOS IC Note 2/ 注意 2...
Page 112
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local Q2006 2SD2654E3/W/ TRANSISTOR D529 BAV199FM DIODE Q2007 MCH3914-H/8/ Q2008 EM6M2 D530 BAV199FM DIODE D531 BAV199FM DIODE Q2009 RE1E002SP SURGE D533 F0K-0420-00 ABSORBER Q2010 BFR193F TRANSISTOR SURGE Q3035...
Page 113
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local D904 EDZV3.6B ZENER DIODE CC73JCH1H101J C CAPACITOR 100pF 50V J CK73HXR0J225M C CAPACITOR 2.2uF 6.3V M D906 1SS390SM DIODE D907 1SS390SM DIODE CK73JXR1C104K C CAPACITOR 0.1uF 16V K D908 1SS390SM...
Page 114
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C109 CK73JXR1C103K C CAPACITOR 0.01uF 16V K C173 CK73JXR1C103K C CAPACITOR 0.01uF 16V K C110 CK73JXR1C104K C CAPACITOR 0.1uF 16V K C174 CK73JXR1C103K C CAPACITOR 0.01uF 16V K C111 CK73FXR0J476M C CAPACITOR...
Page 115
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C264 CK73JXR1C103K C CAPACITOR 0.01uF 16V K C265 CK73FXR1H475K C CAPACITOR 4.7uF 50V K C353 CK73JXR1C103K C CAPACITOR 0.01uF 16V K C267 CK73GXR1C106M C CAPACITOR 10uF 16V M C354 CK73JXR1C103K C CAPACITOR...
Page 116
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C432 CK73JXR1C104K C CAPACITOR 0.1uF 16V K C556 CK73HBB1H103K C CAPACITOR 0.01uF 50V K C557 CC73JCH1H101J C CAPACITOR 100pF 50V J C433 CK73JXR1C104K C CAPACITOR 0.1uF 16V K C434 CK73JXR1C104K C CAPACITOR...
Page 117
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C689 CK73JXR1H152K C CAPACITOR 1500pF 50V K C820 CK73JXR1H471K C CAPACITOR 470pF 50V K C690 CK73HB1C105K C CAPACITOR 1uF 16V K C823 CK73JXR1H471K C CAPACITOR 470pF 50V K C691 CK73HB1C105K C CAPACITOR...
Page 118
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C895 CC730CC1H020B C CAPACITOR 2pF 50V B 1800E C896 CC730CC1H020B C CAPACITOR 2pF 50V B 1800E C974 CK73JXR1H471K C CAPACITOR 470pF 50V K C897 CC730CC1H020B C CAPACITOR 2pF 50V B 1800E...
Page 119
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C1054 CC730CC1H070B C CAPACITOR 7pF 50V B 1800E2 C2008 CK73JXR1H471K C CAPACITOR 470pF 50V K C2009 CK73JXR1H471K C CAPACITOR 470pF 50V K C1054 CC730CC1H060B C CAPACITOR 6pF 50V B 1800E C2010...
Page 120
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C2080 CK73HB1C105K C CAPACITOR 1uF 16V K C3103 CC730ET2A471J C CAPACITOR 470pF 100V J C2081 CK73JXR1H471K C CAPACITOR 470pF 50V K C3105 CC730AY2E050B C CAPACITOR 5pF 250V B 1800E2 C2082...
Page 121
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C3181 CK73JXR1H471K C CAPACITOR 470pF 50V K 1800E2 C4005 CE32BM1E471M E CAPACITOR 470uF 25V M C4006 CK73FXR1E226M C CAPACITOR 22uF 25V M C3182 CK73JXR1H471K C CAPACITOR 470pF 50V K C3183 CK73JXR1H471K C CAPACITOR...
Page 122
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local C4155 CK73GXR1E475K C CAPACITOR 4.7uF 25V K R121 RK73HH1J103D MG RESISTOR 10kΩ 1/16W D C4156 CK73GXR1E475K C CAPACITOR 4.7uF 25V K R125 RK73HB1J102J MG RESISTOR 1kΩ...
Page 123
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local R283 RK73HH1J101D MG RESISTOR 100Ω 1/16W D R380 RK73HH1J223D MG RESISTOR 22kΩ 1/16W D R284 RK73HH1J101D MG RESISTOR 100Ω 1/16W D R381 RK73HH1J223D MG RESISTOR 22kΩ...
Page 124
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local R565 RK73HB1J220J MG RESISTOR 22Ω 1/16W J R465 RK73HH1J103D MG RESISTOR 10kΩ 1/16W D R466 RK73HH1J103D MG RESISTOR 10kΩ 1/16W D R566 RK73HB1J220J MG RESISTOR 22Ω...
Page 125
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local R680 RK73GB2A100J MG RESISTOR 10Ω 1/10W J R900 RK73HB1J102J MG RESISTOR 1kΩ 1/16W J R681 RK73HH1J223D MG RESISTOR 22kΩ 1/16W D R901 RK73HB1J000J MG RESISTOR 0Ω...
Page 126
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local R1007 RK73HH1J101D MG RESISTOR 100Ω 1/16W D R1095 RK73HB1J271J MG RESISTOR 270Ω 1/16W J R1008 RK73HB1J000J MG RESISTOR 0Ω 1/16W J R1096 RK73HB1J000J MG RESISTOR 0Ω...
Page 127
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local R3161 RZ73F0BS2R2J RESISTOR 2.2Ω J R2077 RK73HH1J473D MG RESISTOR 47kΩ 1/16W D R2078 RK73HB1J000J MG RESISTOR 0Ω 1/16W J R3162 RZ73F0BS2R2J RESISTOR 2.2Ω J 1800E2 R2079 RK73HB1J000J...
Page 128
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local R3462 RK73HB1J105J MG RESISTOR 1MΩ 1/16W J R4052 RK73HH1J473D MG RESISTOR 47kΩ 1/16W D R3463 RK73HB1J000J MG RESISTOR 0Ω 1/16W J R4053 RK73HH1J103D MG RESISTOR 10kΩ...
Page 129
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local L252 L3D-0039-00 CHOKE COIL L912 LR73Z0AE220J CHIP INDUCTOR L413 L79-1947-05 FILTER L913 LR79Z0MWR82G CHIP INDUCTOR L414 LB73H0BU-003 CHIP FERRITE L914 LR79G0CQR10G CHIP INDUCTOR L915 LR79G0CQR10G CHIP INDUCTOR L415 LB73H0BU-003...
Page 130
Symbol Symbol Part No. Part Name Description Local Part No. Part Name Description Local L2011 LK73H0BJ15NJ M.CHIP INDUCTOR L2013 LR79G0CQR47G CHIP INDUCTOR L3201 LR79Z0JHR10G CHIP INDUCTOR L2014 LR79Z0CM28NG CHIP INDUCTOR 1800E2 L3300 LB73H0BU-003 CHIP FERRITE L2014 LR79Z0CM22NG CHIP INDUCTOR 1800E L3301 LB73H0BU-003...
Page 131
Symbol Part No. Part Name Description Local TH3000 NCU15WF104F6S N THERMISTOR TH3001 NCU15WF104F6S N THERMISTOR TH3002 NCU15WF104F6S N THERMISTOR W3000 EA120DW-5002A W TO B CONNE L77-1802-05 QUARTZ CRYSTAL X251 L7J-0164-00 QUARTZ CRYSTAL X900 L7H-0152-00 TCXO XF700 L7B-0058-00 3-24(No.RA094<Rev.002>)
Page 132
Packing materials and accessories parts list / 包装材料及配件清单 Block No.M2MM Packing and accessories / 包装及配件 Block No. [M][2][M][M] Symbol No. Part No. Part Name Description Local B5A-3612-10 INST.MANUAL US,CAN,OCEANIA,ASIA,EU,UK,IND,CHINA 1800E2 B5A-4136-00 INST.MANUAL US,OCEANINA 1800E --------- PAMPHLET FOSS E3A-0772-00 DC CORD ASSY F3B-0004-00 REINFORCING HW CONNECT SETS...
Page 133
JVCKENWOOD Corporation Communications Systems Division (No.RA094<Rev.002>) Printed in Japan...