Table of Contents
Advertisement
"1 Channel spacing
Europe,
UK.
Australia
An AM channel spacing switch is provided cr
the rear panel for selecting 9 kHz or 10 kHz
steps according to your area (not provided cr
tuners for the U.K.. Australia and Continertai
Europe).
anc SPACING >)
(" 1OkHz,
Example
|
L
Beispiel
Exemple
|
Voorbeeld
Fig. 12
Ejemplo
Abb. 12
Exempel
Afb. 12
To change the AM channel spacing:
First, turn the power on, press the FM buticr
to set to the FM mode, then disconnect 'he
power cord. Wait for a few seconds and switc>
over the AM channe! scacing switch as shows
in Fig. 12. using the tip of a ball-point pen
"2 Pressing the TUNING (UP/DOWN) buttons ' #i
sample stations up or down a selected banc
in the following frequency steps.
AM/
| AM/
MW
LW
9 kHz
DR-E34BK
50 kHz
© Your receiver allow selection between the
MW and LW bands while tuning in,
* If you receiver reaches the upper- or lower-
limit while scanning with the UP or DOWN
button, it reverts to the lower- or upper-lim.t
frequency automatically and continue with
scanning further,
*3 Turn the DOLBY 8 NR-button ON to recerc
with a Doiby system on or to piay back atace
recorded on a Dciby system
* Dolby noise reduction manufactured uncer
license from Doiby Laboratories Licensirg
Corporation.
"DOLBY" and the double-D symbo!
OO are
trademarks of Doiby Laboratories Licensinc
Corporation.
BASIC OPERATIONS
1. Turn the power on.
ON:
Press the POWER
button to turn the
power ON.
Note:
*
Turn volume to ''MIN"' before turning pow-
er ON.
STAND BY:
Press the POWER button again
to turn the power STAND BY mode. (The indi-
cator lights.)
2. Select a source.
Press a source selector button of your choos-
ing, making sure its indicator lights.
To
listen to brodcasts:
Press the TUNER button (see page 10).
¢ To listen to discs:
Press the CD button
¢ To listen to tapes:
Press the TAPE button (see page 11).
*To listen to records:
Press the PHONO button (see page 14).
* Press the VIDEO/AUX button to listen to the
sound from the source piugged into the
VIDEO/AUX jack (see page 14).
Operate each component to start playback
or recording.
Notes:
° When listening to tapes or CD by the
COMPU LINK system, simply press the
associated PLAY(
> )or( <J ) button
and source will be switched to TAPE or
CD automatically.
While presetting the FM/AM button, sim-
ply press the preset stations button and
source will be switched to TUNER.
* After switching
is made,
previously
played TAPE or CD will automatically
stop.
«When connecting a CD player with the
COMPU LINK SYSTEM, only JVC equip-
ment associated with this system can be
operated. (How to connect, see page 3)
3. Adjust the sound volume.
Turn the VOLUME control to the MAX side
(clockwise) to increase the sound volume, to
the MIN side (counterclockwise) to reduce it.
4. Adjust the tone to your liking.
Vertical
motion
of this S.E.A.
GRAPHIC
EQUALIZER Control allows you to select five
levels of sound quality, from deep base (63 Hz)
to treble (16 kHz).
. Frequency
i band
Feature
* 63 Hz
(Deep bass)
Firm, stable tone
' 250 Hz
i
;
- (Bass)
Powerful, crisp tone
1 kHz
Tone full of presence,
. (Mean)
with sharp vocal sound,
T
1 4 kHz
|
.
i
| (Mean treble)
Clear, bright tone
| 16 KHz
Expansive. delicate
1
| (Treble)
[tone
|
¢ The S.E.A. GRAPHIC EQUALIZER controi
at the ''O"' position delivers a flat sound.
¢ Move the control up to enhance tonal effects.
down to lessen them.
« Adjust the sound quality for the left and right
speakers independently.
DR-E34BK
DR-E34LBK
(No. 20162)
1-9
Advertisement
Table of Contents
