Maintenance; Register Online - DeWalt DCBL777 Instruction Manual

• Install the battery pack
• Hold the blower with one hand as shown in Fig. H.
• Power the blower on.
• With the tube 5 positioned several inches above the
ground, and using a sweeping motion from side to side,
advance slowly keeping the accumulated debris/leaves
in front of you as shown in Fig. H.

MAINTENANCE


WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning

WARNING:
all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI
Z87.1 approved eye protection when performing
this procedure.

WARNING:
harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened only
with water and mild soap. Never let any liquid get inside
the tool; never immerse any part of the tool into a liquid.
Accessories

WARNING:
those offered by D
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
D WALT recommended accessories should be used with
e
this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Tool Connect™ Chip (Fig. K)

WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
15 into the tool handle.
To reduce the risk of serious
Blow dirt and dust out of
Never use solvents or other
Since accessories, other than
WALT, have not been tested with
e
WALT. Call 1‑800‑4‑D
e
To reduce the risk of serious
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your smart
device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the housing.
Secure it with the retaining screws and tighten the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.

WARNING:
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a factory service
center or an authorized service center. Always use
identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
Three‑Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/
support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
WALT
e
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
20 that hold the Tool
19 into the tool.
18 .
To assure product SAFETY and
WALT Industrial Tool Co., 701 East
e
English
WALT
e
WALT
e
11