Advertisement
: Allow engine and exhaust components to cool before refuelling.
: DO NOT smoke.
: never refuel the machine indoors.
: never store the machine or fuel container inside where there is an open flame, such as a water heater.
If fuel is spilt, DO NOT attempt to start the power source, but move the machine away from the area of spillage before starting.
8
Always replace and securely tighten the fuel cap after refuelling.
9
If the fuel tank is drained, this should be done outdoors.
9
Before starting the machine, look into the feeding chamber to make certain that it is empty.
9
Keep your face and body away from the feed intake opening.
9
DO NOT allow hands or any other part of the body or clothing inside the feeding chamber, discharge chute, or near any moving part.
8
Keep proper balance and footing at all times. DO NOT overreach. Never stand at a higher level than the base of the machine when
9
feeding material into it.
Always stand clear of the discharge zone when operating this machine.
9
When feeding material into the machine be extremely careful that pieces of metal, rocks, bottles, cans or other foreign objects are not
9
included.
If the cutting mechanism strikes any foreign objects or if the machine should start making any unusual noise or vibration, shut off the
9
power source and allow the machine to stop. Disconnect the spark plug wire from the spark plug (electric unit disconnect from supply)
and take the following steps:
: inspect for damage.
: check for and tighten any loose parts .
: have any damaged parts replaced or repaired with parts having equivalent specifications.
DO NOT allow processed material to build up in the discharge zone. this may prevent proper discharge and can result in kickback of
8
material through the feed intake opening.
If the machine becomes clogged at the inlet opening or discharge chute shut off the power source and disconnect the spark plug wire
9
or remove the ignition key before clearing debris in the inlet opening or discharge chute. Keep the power source clear of debris and other
accumulations to prevent damage to the unit or possible fire. Remember that operating the starting mechanism on engine
powered machines will still cause the cutting blades to move.
Keep all guards and deflectors in place and in good working condition.
9
DO NOT tamper with the power source governor settings; the governor controls the safe maximum operating speed and protects the
8
power source and all moving parts from damage caused by over-speed. Seek authorised service if a problem exists.
DO NOT transport this machine while the power source is running.
8
Shut off the power source and disconnect the spark plug lead (electric unit disconnect from supply) whenever you leave the work area.
9
DO NOT tilt the machine while the power source is running.
8
Position the machine such that it is not necessary to work downwind of the exhaust.
9
2. INTRODUCTION
Safe and easy way to chip wood, powered by a 420cc engine with a speed of 3600rpm. Chips wood almost instantly upon contact, keeping
labour and work time to a minimum. Features self-feeding chipping hopper and adjustable height of the discharge port. Supplied with wheels
for easy manoeuvrability. Chipping capacity: 100mm. Fuel type: Unleaded Petrol. Motor Power: 15hp/3600rpm. Overall Size (W x D x H): 842 x
1285 x 1245mm.
3. SPECIFICATION
Model no.: ................................................................SWC420
Blade Speed: ........................................................... 2400rpm
Drive Type: ............................................................Belt Driven
Engine Capacity: .......................................................... 420cc
Engine Type: .................................. Overhead Valve 4-Stroke
Fuel Tank: ....................................................................... 6.5L
Fuel: .............................. Unleaded 95 RON - E10 compatible
Max. Engine Speed: ................................................. 3500rpm
Maximum Power: ........................................15hp @ 3600rpm
Noise Rating: ................................................. 114/94.3 dB(A)
Oil Volume: ..................................................................... 1.1L
Starting System: ........................................................... Recoil
Noise Test Code: ...................................... EN ISO 3744:1995
4. ASSEMBLY
4.1.
COMPONENT PARTS
fig.2
© Jack Sealey Limited
ITEM
Description
A
Support
B
Axle
C
Tyres
D
Feed Hopper
E
Discharge Port
F
Bolt M8x20
G
Ø8 Spring Washer
H
Ø8x20x2 Washer
I
Hex. nut M8
J
Ø8 Plain Washer
K
Bolt M6 x 12
L
M6 Wing Nut
M
Ø6xØ18x1.6 Washer
N
Bolt M6x20
O
Hex Nut M6
Original Language Version
fig.1
Qty.
1
2
2
1
1
4
6
4
2
2
2
2
2
2
2
SWC420
Issue 1
07/11/23
Advertisement
