Philips TAA3206 - Headphones 3000 Series Manual

Also See for TAA3206:

User manual (14 pages)

Table of Contents

Contents

1 Your Device
2 Get started
- 2.1 Charge the battery
- 2.2 Pair the unit with your mobile phone
3 Use your device
- 3.1 Connect the unit to your Bluetooth device
- 3.2 Manage your calls and music
4 Technical data
5 Remove the integrated battery
6 Frequently asked questions
7 Important safety instructions
- 7.1 Hearing Safety
- 7.2 General information
8 Documents / Resources
- 8.1 References
- 8.2 Download manual

Philips TAA3206 - Headphones 3000 Series Manual

Your Device

To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. With this Philips in-ear headphones, you can:

enjoy convenient wireless handsfree calls;
enjoy and control wireless music;
switch between calls and music.

What's in the box

Other devices

A mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headphone (see 'Technical data').

Overview of your product

Volume +
Power button
Volume -
LED indicator
Microphone
Type C charging slot

Get started

Charge the battery

Note

Before you use your headphone for the first time, place the headphones in the charging case and charge the battery for 2 hours for optimum battery capacity and lifetime.
Use only the original USB charging cable to avoid any damage.
Finish your call before charging the headphone, as connecting the headphone for charging will power the headphone off.

Connect the supplied Type C charging cable to:

Type C charging slot on the headphones and;
The charger/USB port of a computer.

→ LED turns white during charging and turns off when the headphones in fully charged.

Tip

Normally, a full charge takes 2 hours.

Pair the unit with your mobile phone

Before you use the headphones with your mobile phone for the rst time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and mobile phone. The headphones store the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest paired device is replaced by the new one.

Make sure that the headphones are fully charged and turned off.
Press and hold for 5 seconds until the blue and white LED flashes alternately.
→ The headphone remain in pairing mode for 5 minutes.
Make sure that the mobile phone is turned on and its Bluetooth feature is activated.
Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone.

The following example shows you how to pair the headphones with your mobile phone.

Activate the Bluetooth feature of your mobile phone, select Philips TAA3206
Enter the headphone password "0000" (4 zeros) if prompted. For those mobile phones featuring Bluetooth 3.0 or higher, no need to enter a password.

Use your device

Connect the unit to your Bluetooth device

Turn on your mobile phone/ Bluetooth device.
Press and hold the on/off button to turn the headphones on.
→ The blue LED is on 1s.
→ The headphones are reconnected to the last connected mobile phone/ Bluetooth device automatically. If the last one is not available, the headphones will be in pairing mode.

Tip

If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone/Bluetooth device manually.

Note

If the headphones fail to connect to any Bluetooth device within range in 5 minutes, it will switch off automatically to save the battery life.

Manage your calls and music

On/off
Task	Button	Operation
Turn the headphones on.	Power button	Press and hold for 2 seconds.
Turn the headphones off. Music control	Power button	Press and hold for 4 seconds. → The blue LED is on 1 second.
Task	Button	Operation
Play or pause music.	Power button	Press once.
Adjust volume.	+/-	Press once.
Next track.	+	Long press.
Previous track.	-	Long press.
Call control
Task	Button	Operation
Pick up/ hang up a call.	Power button	Press once.
Switch caller during a call.	Power button	Press twice.
Other headphones indicator status
Headphones status Indicator
The headphones are connected to a Bluetooth device, while the headphones in standby mode or while you are listening to music.	The blue LED flashes for every 4 seconds
The headphones are ready for pairing.	The LED flashes blue and white alternately.
The headphones are on but not connected to a Bluetooth device.	The white LED flashes for every 3 seconds. If no connection can be made, the headphones will turn itself off within 5 minutes.
Low battery level.	The white LED flashes once for every 3 seconds until it is out of power.
Battery is fully charged.	White LED is off

Technical data

Music time: 10 hours
Talk time: 10 hours
Standby time: 55 hours
Charging time: 2 hours
Rechargeable lithium polymer battery (85 mAh)
Bluetooth version: 5.0
Compatible Bluetooth profiles:
- HFP (Hands-Free Profile-HFP)
- A2DP (Advanced Audio Distribution Profile)
- AVRCP (Audio Video Remote Control Profile)
Supported audio codec: SBC
Frequency range: 2.402-2.480 GHz
Transmitter power: < 10 dBm
Operating range: Up to 10 meters (33 feet)
Digital echo & noise reduction
Auto power off
USB-C port for charging
Supports SBC
Low battery warning: available

Note

Specifications are subject to change without notice.

Remove the integrated battery

If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.

Make sure the headphone is disconnected from the charging case before removing the battery.

Frequently asked questions

My device does not turn on

The battery level is low. Charge the headphone.

I cannot pair my unit with my Bluetooth device

The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the headphone.

The Bluetooth device cannot find the unit

The headphone may be connected to a previously paired device. Turn off the connected device or move it out of range.
Pairing may have been reset or the headphone has been previously paired with another device. Pair the headphone with the Bluetooth device again as described in the user manual. (see 'Pair the unit with your Bluetooth device at the first time').

My Bluetooth headphone is connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone. Select to listen to music through the headphone.

The audio quality is poor and crackling noise can be heard.

The Bluetooth device is out of range. Reduce the distance between your headphone and Bluetooth device, or remove obstacles between them.
Charge your headphone.

The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.
Make sure your mobile phone not only supports (mono) HFP but alos supports A2DP and is BT4.0x (or higher) compatible (see 'Technical data).

I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward).
Make sure the Bluetooth audio source supports AVRCP (see 'Technical data').

The volume level of the unit is toot low

Some Bluetooth devices cannot link the volume level with the headphone through volume sync. In this case, you have to adjust the volume on your Bluetooth device independently to achieve an appropriate volume level.

I cannot connect the headphone to another device, what do I do?

Make sure the Bluetooth function of the previous paired device is turned off.
Repeat the pairing procedure on your second device (see 'Pair the unit with your Bluetooth device at the first time').

Important safety instructions

Hearing Safety

To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.

Be sure to observe the following guidelines when using your earpieces.

Listen at reasonable volumes for reasonable periods of time.
Be careful not to adjust the volume continuously upwards as your hearing adapts.
Do not turn up the volume so high that you can't hear what's around you.
You should use caution or temporarily discontinue use in potentially hazardous situations.
Excessive sound pressure from earphones and headphones can cause hearing loss.
Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.
For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

General information

To avoid damage or malfunction:

Do not expose headphones to excessive heat
Do not drop your headphones.
Headphones shall not be exposed to dripping or splashing.
Do not allow your headphones to be submerged in water.
Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

About operating and storage temperatures and humidity

Store in a place where temperature is between -20°C (-4°F) and 50°C (122°F) (up to 90% relative humidity.
Operate in a place where temperature is between 0°C (32°F) and 45°C (113°F) (up to 90% relative humidity.
Battery life may be shorter in high or low temperature conditions.
Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion;
Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas;
A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.