Philips TAA7306 - Headphones 7000 Series Manual

Register your product and get support at www.philips.com/support

Your Bluetooth wireless earpieces

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support. With this Philips wireless headphones, you can:

• enjoy convenient wireless handsfree calls;
• enjoy and control wireless music;
• switch between calls and music.

What's in the box

Philips True Wireless earpieces Philips TAA7306

Replaceable rubber ear caps x 3 pairs

Wing-tips x 3pairs

Ear hook x 3 pairs

Carrying pouch

USB charging cable (for charging only)

Quick start guide

Global Warranty

Safety leaflet

Other devices

A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the earpieces (see 'Technical data').

Overview of your Bluetooth wireless earpieces

1. Microphone
2. LED indicator (Earbud)
3. Touch panel
4. Heart rate monitor (HRM) sensor (Right side only)
5. Operation LED (Charging case)
6. LED indicator ( charging case )
7. USB-C charging slot
8. Reset button

Get started

Charge the battery

Note

• Ÿ Before you use your earpieces for the first time, place the earpiecess in the charging case and charge the battery for 3 hours for optimum battery capacity and lifetime.
• Ÿ Use only the original USB charging cable to avoid any damage.
• Ÿ Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces off.

Charging case

Connect one end of the USB cable into the charging case, and another end into the power source.
The charging case starts charging.

• Charging process is verified by the white LED light next to the USB socket on the case.
• When the charging case is fully charged, the light goes off.
  

Tip

• The charging case serves as a portable backup battery for charging the earpieces. When the charging case is fully charged, it supports 3 full recharge cycle for the earpieces.

Earpieces

Place the earpieces in the charging case.
The earpieces start charging.

• Charging process is verified by white LED light on the earpiecess.
• When the earpieces is fully charged, the white light goes off.
  

Tip

• Ÿ Normally, a full charge takes 2 hours (for the earpieces or charging case).

Pair the earpieces with your Bluetooth device at the first time

1. Auto Power on: Open the charging capsule, the earpiecess discharged and the blue LED indicator flash with "power on" voice prompt.
2. Manual Power on: On both earpiecess press and hold the multi-function buttons for approxinmately 2 seconds.
   
   The LED on both earpiecess flashes in blue for 3 times, and then it flashes in white.
   Both earpiecess are now power on and are paired with each other.
   The earpiecess are now in pairing mode and is ready to pair with a Bluetooth device (e.g. a mobile phone)
3. Turn on the Bluetooth function of your Bluetooth device.
4. Pair the earpiecess with your Bluetooth device. Refer to the user manual of your Bluetooth device.

Note

• After powering on, if the earpieces cannot find any previously connected Bluetooth device, it will automatically switch to pairing mode.

The following example shows you how to pair the earpieces with your Bluetooth device.

• Turn on the Bluetooth function of your Bluetooth device, select Philips TAA7306.
• Enter the earpieces password "0000" (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password.
  Philips TAA7306

UV sterilization function

Put the earpieces into charging case and close the lid, the UV sterilization LED will turn on for 1 minute.

Pair the earpieces with another Bluetooth device

If you have another Bluetooth device that you want to pair with the earpieces, make sure the Bluetooth function in any other previously paired or connected devices are turned off. Then follow the steps in 'Pair the earpieces with your Bluetooth device at the first time'.

Note

• Ÿ The earpieces stores 1 device in the memory. If you try to pair more than 2 devices, the earliest paired device is replaced by the new one.

Use your Headphones

Connect the earpieces to your Bluetooth device

1. Turn on the Bluetooth function of your Bluetooth device.
2. Open the top cover from charging box.
   The blue LED flashes.
   The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected one is not available, the earpieces will search and reconnect to the second last connected device.

Tip

• Ÿ The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
• Ÿ If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manully.

Note

• Ÿ If the earpieces fails to connect to any Bluetooth device within 5 minutes, it will turn off automatically to save the battery life.
• Ÿ In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually.

Power on/off

Manage your calls and music

Music control

Call control

Voice control

Battery LED indicator on Bluetooth device

It will show a battery indicator on Bluetooth device after connected to earpieces.

LED indicator status

Heart rate monitor

Philips headphones APP

	Current heart rate
	Highest heart rate
	Lowest heart rate
	Average heart rate

Note

• The HRM function supports Philips Headphone APP.

Awareness mode

Factory reset the earpieces

Earpieces

• Music time: 6 hours (additional 18 hrs with charging case)
• Talk time: 6 hours (additional 18 hrs with charging case)
• Standby time: 200 hours
• Charging time: 2 hours
• Rechargeable lithium ion battery: 105 mAh on each earpieces
• Bluetooth version: 5.0
• Compatible Bluetooth profiles:
  • HSP (Hands-Free Profile-HFP)
  • A2DP (Advanced Audio Distribution Profile)
  • AVRCP (Audio Video Remote Control Profile)
• Supported audio codec: SBC, AAC
• Frequency range: 2.402 -2.480GHz
• Transmitter power: < 10 dBm
• Operating range: Up to 10 meters (33 feet)

Charging case

• Charging time: 2 hrs
• Rechargeable Li-ion battery: 450mAh

Note

• Specifications are subject to change without notice.

Remove the integrated battery

If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.

• Make sure the earpieces is disconnected from the charging case before removing the battery.
  
• Make sure the charging case is disconnected from the USB charging cable before removing the battery.
  

Frequently asked questions

My Bluetooth earpieces does not turn on.
The battery level is low. Charge the earpieces.

I cannot pair my Bluetooth earpieces with my Bluetooth device.
The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the earpieces.

Pairing does not work.

• Put both earpiecess into charging case.
• Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
• On your Bluetooth device, delete "Philips TAA7306" from the Bluetooth list.
• Pair your earpieces (see 'Pair the earpieces with your Bluetooth device at the first time').

How to reset pairing.
Take both earpiecess out of the charging case. Press twice on both earpiecess Multi-function buttons until the LED indicator turns white, wait for about 10 seconds. You will hear "Connected", "Left Channel", "Right Channel", as pairing successful.

The Bluetooth device cannot find the earpieces.

• The earpieces may be connected to a previously paired device. Turn off the connected device or move it out of range.
• Pairing may have been reset or the earpieces has been previously paired with another device. Pair the earpieces with the Bluetoot device again as described in the user manual. (see 'Pair the earpieces with your Bluetooth device at the first time').

My Bluetooth earpieces is connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker.
Refer to the user manual of your mobile phone. Select to listen to music through the earpieces.

The audio quality is poor and crackling noise can be heard.

• The Bluetooth device is out of range. Reduce the distance between your earpieces and Bluetooth device, or remove obstacles between them.
• Charge your earpieces.

The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all.
Make sure your mobile phone not only supports (mono) HSP/HFP but alos supports A2DP and is BT4.0x (or higher) compatible (see 'Technical data').

I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/backward).
Make sure the Bluetooth audio source supports AVRCP (see 'Technical data').

The volume level of the earpieces is toot low.
Some Bluetooth devices cannot link the volume level with the earpieces through volume sync. In this case, you have to adjust the volume on your Bluetooth device independently to achieve an appropriate volume level.

I cannot connect the earpieces to another device, what do I do?

• make sure the Bluetooth function of the previous paired device is turned off.
• Repeat the pairing procedure on your second device (see 'Pair the earpieces with your Bluetooth device at the first time').

I hear sound from only one earpieces.

• If you are in a call, it is normal that sound comes from the right and left earpieces.
• If you are listening to music but sound only comes from one earpieces:
  • The other earpieces may be out of battery. For optimal performance, charge both earpieces fully.
• The right and left earpiecess are disconnected from each other, Turn off both earpieces first. Then put both earpiecess back to charging case for 5 seconds and take them out. This will turn the earpiecess on and connect the two earpiecess. Reconnect the earpieces to your Bluetooth device.
• The earpieces is connected to more than one Bluetooth device. Switch off the Bluetooth function of all connected devices. Turn off both earpiecess. Put both earpiecess back to charging case for 5 seconds and take them out. Reconnect the earpieces to your Bluetooth device. Note that the earpieces is desighed for connecting to only one Bluetooth device ath a time. When you reconnect the earpieces to your Bluetooth device, make sure the Bluetooth function of any other Previously paired/connected devices are off.
• If the above solutions do not help, factory reset the earpieces (see 'Factory reset the earpieces'.

For further support, visit www.philips.com/support.

• Ÿ Do not expose headphones to excessive heat Ÿ Do not drop your headphones.
• Ÿ Headphones shall not be exposed to dripping or splashing.
• Ÿ Do not allow your headphones to be submerged in water.
• Ÿ Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
• Ÿ If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
• Ÿ The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
• Ÿ Replacement of a battery with an incorrect type that can defeat a safeguard;
• Ÿ Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;
• Ÿ Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;
• Ÿ A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
• Ÿ Never use your headphones when you are operating a motor vehicle, riding a bicycle, running or walking in traffic areas. It is dangerous and illegal in many places.