Yamaha RS-150 Assembling Instructions

RS150
ASSEMBLY INSTRUCTIONS
INTRODUCTION
Thank you for purchasing the Yamaha Electronic Drum Rack System RS150.
Before using, thoroughly read these assembly instructions, and use this product
safely and correctly.
PRECAUTIONS
Before using, please read this "Assembly In-
struction" sheet, and use this product in a safe
and proper manner.
Especially for children, parents or an instructor
should teach the children the proper manner in
which to use the device.
If this symbol is ignored and the equipment is used improperly, fatal injury to per-
WARNING
sons or serious damage could occur.
Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the
instrument being unstable and overturning.
Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury.
When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or
causing injury to hands or fingers.
Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury.
Please be careful when children are close to or touching the product. The product has many pipes and arms so careless
movement around the product may result in injury.
When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may
become entangled in the cables resulting in falls.
If this symbol is ignored and the equipment is used improperly, there is a danger
CAUTION
of injury to persons handling the equipment, and material damage could occur.
Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury.
Watch your fingers when adjusting clamps. They may become pinched resulting in injury.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.
Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.
* Specifications are subject to change without notice.
■ RS150 Assembly
* Parts for the RS150's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly.
A Phillips (+) screwdriver is required when attaching the DTXTREME
1
After removing the unit from the box, remove all cushion material.
2
Setting up the parts
Follow the setup order (q~o) in the diagrams shown below.
q
Temporarily remove the leg connector from pillar (R).
w
Attach center pipe (D) to pillar (R) and pillar (C), and secure.
e
Reattach the leg connector.
r Attach the cross pipe to the leg connector.
t Attach center pipe (C) to pillar (L) and pillar (C), and secure.
Caution
: Make sure the bolts marked with a "
Piller (L)
Center Pipe (A)
i
Holder Clamp Holder Clamp
u
Module Holder
t
$ Caution
Center Pipe (C)
Leg (C)
Leg (L)
To prevent against accidents and injury
Please follow the cautions listed below
Caution (including danger, or warning). This
mark indicates cautions in which you should
pay close attention to.
Acts indicated with this icon are prohibited and
should not be attempted.
II
S. Please prepare one before starting assembly.
" are loosened before setting up.
Piller (C)
Holder Clamp
Center Pipe (B)
Piller (R)
Holder Clamp
Leg Connector
y
q
e
w
Center Pipe (D)
r
Cross Pipe
Leg (R)
Leg Connector
■ Handling Precautions
• Do not alter the product. Doing so may result in damage or deterioration to the product.
• Do not step on or place heavy objects on the product. It may result in damage.
• Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to
a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It may result in deformation,
discoloration, stickiness, damage or deterioration.
• To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the
product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been
wrung out thoroughly to remove any remaining detergent. Do not use benzine, thinner or alcohol as it may
result in discoloration or deformation. Also pay close attention so as not to let the water and detergent come
into contact with the cushions used in the product, it may result in deterioration.
■ Inside This Package
Before setup, please make sure that all of the items listed below are present and ac-
counted for. If anything is missing, please contact the dealer from whom you purchased
the unit.
* Before assembling the rack stand, make sure all of the parts shown below are included.
◆Piller （L） ◆Piller （C）
◆Module Holder
◆Tom Clamp CL-940A（x4）
◆ Cymbal Holder CH740（x2）
y
Attach center pipe (B) to pillar (R) and pillar (C), and secure.
u
Attach center pipe (A) to pillar (L) and pillar (C), and secure.
i
Attach the module holder to pillar (L), and secure.
o
Attach the cymbal holders and tom clamps to the holder clamps, and secure.
Cymbal Holder
(CH740)
o
Remove temporarily.
Tighten knob of
leg connector
Memory Clamps
Using the memory clamps let you obtain the same
height setting for all future setups.
◆Piller （R）
◆Center Pipe （A）
Leg Connector
◆Center Pipe （B）
◆Center Pipe （C）
◆Cross Pipe
◆Center Pipe （D）
◆Cymbal Holder CH745
◆Small Screws M5 x 8
◆Cable Band（x10）
（Module Holder Fixing Screws x4）
◆Assembly Instructions
（this sheet）
Cymbal Holder
(CH740)
Tom Clamp
(CL-940A)
Tom Clamp
(CL-940A)
o
o
o
o
Holder Clamp
Holder Clamp
Holder Clamp
Holder Clamp
Cymbal Holder
(CH745)
Tom Clamp
(CL-940A)
o