Operation - DeWalt DCN650N Original Instructions Manual

English
To Remove the Battery Pack from the Tool
1. Press the release button
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Low Battery Indicator (Fig. A, B)
The low battery indicator is an integrated feature in the
left‑hand worklight. It will blink 4 times to indicate that
the battery pack needs to be recharged and the tool will
automatically shut down.
Switch off the tool and take out the battery pack
as soon as the indicator blinks.
The tool remains non‑operational as long as a low battery pack
is attached to it.
Selecting the Mode (Fig. E)
To select sequential action mode, slide the mode selector
9
switch to the single nail icon
To select bump action mode, slide the mode selector switch
to the three nail icon ( )
Non‑mar Tip (Fig. A)
11
Place the no‑mark tip over the contact trip
is used on wood.
Store the no‑mark tip at the holder
be used.

WARNING: Make sure the trigger lock‑off
and the battery pack is removed before installing or
removing the no‑mark tip.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
12
16
and firmly pull the battery pack
14
to charge it
).
6
when the tool
12
whenever it is not to
2
is engaged
Proper Hand Position (Fig. I)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand the main handle.
Actuating the Tool (Fig. A)
The DCN650 can be operated using one of two modes:
sequential action mode or bump action mode.
Sequential Action Mode (
The sequential action mode is used for intermittent nailing
when very careful and accurate placement is desired.
1. Use the mode selector switch
action mode.
2. Release the trigger lock‑off
3. Push the contact trip
4. Pull the trigger switch
5. Release trigger and remove contact trip from work piece.
6. Repeat steps 3 ‑ 5 to fire subsequent nails.
Bump Action (
The bump action mode is used for rapid nailing on flat,
stationary surfaces.
1. Use the mode selector switch
action mode.
2. Release the trigger lock‑off
a. To drive a single nail, operate the tool as described for
sequential action:
Push the contact trip
9
b. Pull the trigger switch
3. To drive several nails, depress and hold the trigger switch
and then push the contact trip
work surface. Each time the contact trip
whilst the trigger

WARNING: Do not keep the trigger depressed when the
tool is not in use. Keep the trigger lock‑off
position to prevent accidental actuation when the tool is
not in use.
Preparing the Tool (Fig. A)
1. Remove battery pack and all nails from the magazine.
2. Check if the contact trip and nail pusher can move freely.
3. Reload the nails to the magazine.

WARNING: Do not use the tool if the contact trip or nail
pusher cannot move freely.
CAUTION: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
Trigger Lock‑off (Fig. F)
This tool is equipped with a trigger lock‑off
the tool from firing a nail.
)
9
, select the sequential
2
.
11
against the work surface.
1
to actuate the tool.
)
9
to select the bump
2
.
6
against the work surface.
1
to actuate the tool.
6
repeatedly against the
2
is depressed
1
is held, a nail will fire.
2
which prevents
1
,
2
in the locked