Sealey MIGHTYMIG250.V2 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear a welding
instructions
mask
Breathing Electromagnetic
welding fields can cause
fumes can be pacemaker
hazardous to malfunction.
your health.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
‰
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any
other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate
safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend
that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into
a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by
contacting your Sealey stockist. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2. and
use a Portable Appliance Tester.
1.1.4.
Ensure that cables are always protected against short circuit and overload.
1.1.5.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose.
1.1.6.
Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that the supply is correctly fused.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified
electrician.
1.1.10. MIGHTYMIG250 is a single phase machine and must be run from a minimum 16amp supply.
To achieve maximum output this model will require a 30Amp fused supply. We recommend you discuss the installation of an
industrial round pin plug and socket with your electrician.
Fit a plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
1.1.11. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD fitted is recommended
since any product which is plugged into the cable reel will be protected. The cross-section of the cable on the cable reel must be suitable
for the unit and never lower than the cross-section of the mains cable supplied with the unit.
1.2. GENERAL SAFETY
▲ DANGER! Unplug the welder from the mains power supply before performing maintenance or service.
Keep the welder and cables in good condition. Take immediate action to repair or replace damaged parts.
9
Use genuine parts and accessories only. Unapproved parts may be dangerous and will invalidate the warranty.
9
Use an air hose to regularly blow out any dirt from the liner and keep the welder clean for best and safest performance.
9
Check and spray the gas cup and contact tip regularly with anti-spatter spray which is available from your Sealey stockist.
9
Locate the welder in a suitable work area. Ensure that the area has adequate ventilation as welding fumes are harmful.
9
Keep work area clean, tidy and free from unrelated materials. Also ensure that the work area has adequate lighting and that a fire
9
extinguisher is at hand.
WARNING! Use welding head shield to protect eyes and avoid exposing skin to ultraviolet rays given off by electric arc. Wear
‰
safety welding gauntlets.
Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery and contain long hair.
9
© Jack Sealey Limited
250AMP PROFESSIONAL GAS/NO-GAS MIG
WELDER WITH EURO TORCH
MODEL NO:
Wear protective Electrical shock
gloves hazard
Welding sparks
can cause
explosions or
fire.
Original Language Version
MIGHTYMIG250.V2
Warning: Caution required
Avoid damp / wet
Arc rays can Electric shock
burn eyes and from welding
injure skin. electrodes can
kill.
MIGHTYMIG250.V2 Issue 2(F) 22/12/21