Related Manuals for Haier HHX1030 - 05-05
Summary of Contents for Haier HHX1030 - 05-05
-
Page 1: Range Hood
Range Hood Extractor de Aire Hotte de Cuisiniere Haier User Manual Model HHX1030 Guide de l’Utilisateur HHX1030 Manual del Usuario Modelo HHX1030... -
Page 2: Safety Precautions
English SAFETY PRECAUTIONS Warning! – To reduce the risk of fire, electric shock, or injury to persons, always exercise basic safety precautions, including the following: 1. Read all instructions before using the appliance. 2. Use this appliance only for its intended purpose as described in this user manual. - Page 3 English To reduce the risk of personal injury in the event of a range top grease fire: 1. NEVER pick up a flaming pan, as you may be injured. 2. DO NOT use water, including wet dishcloths or towels, to put out a fire. A violent steam explosion may result.
-
Page 4: Table Of Contents
1 User Manual Check to make sure that all parts and accessories are present and in good condition. If you find that they are not in good condition or are missing, please contact our customer service department for assistance. Our Toll-Free number... -
Page 5: Installation Preparation
1. Remove the range hood from the carton. 2. Lay the range hood upside down on a table covered with either cardboard or paper to prevent scratching the hood or table. 3. Unscrew the lamp cover with a Phillips head screwdriver. -
Page 6: Selecting Venting Direction
If a wall cap is used directly off the back of the hood, special care must be taken to ensure that the damper in the damper/duct connector on the hood and the damper in the wall cap do not interfere with each other when the range hood is operating. -
Page 7: Cabinet Preparation For Hoods Support
English For model HHX1030 you must remove the vent cover from the slots on the front of the range hood. Save the vent cover for possible future use. Cabinet Preparation for Hood Support Mount the hood so that the bottom of the hood is between 24”-30” above the stovetop. -
Page 8: Preparing Duct Connections
Note: Section “D” and “E” remain with the hood. fig. 3 5. Mount the round collar (E22A -not supplied) over the opening on the hood by using 3 shorter screws. Allow the bottom edge of the 7” duct to be inserted into the collar. -
Page 9: Wiring Diagrams
Your new range hood will operate at the highest efficiency if the number of elbow and the length of the duct are kept to a minimum. The back draft damper flap attached to the damper frame assembly, which is supplied with the hood, does not impede airflow significantly. -
Page 10: Hood Installation
Caution! All wiring installation must comply with local and national electrical code regulations. 5. Attach ductwork and use duct tape to seal all joints. 6. After turning all range hood switches to the OFF position, turn the power ON and test your installation. -
Page 11: Use And Care
All parts may be obtained from service centers authorized by Haier, or may be ordered directly from Haier. When ordering parts, please specify the range hood model number on the rating label, which is located on the inside of the range hood. -
Page 12: Troubleshooting
If you see a metal duct leading away from the vent hood, then you have a system that vents to the outdoors. If you do not see a duct, your unit may be venting through the back wall. -
Page 13: Warranty Information
The mechanical and electrical parts (including • Damages from shipping labor costs) contained in this Haier product, for a period of 12 months, from the date of • Damages from misuse, abuse, accident, purchase (for commercial or rental applications, alteration, lack of proper care and the warranty is 90 days). - Page 14 IMPORTANT Ne pas retourner cet article au magasin En cas de problème avec cet article, veuillez contacter le « Centre satisfaction client » de Haier au 1-877-337-3639. UNE PREUVE D’ACHAT DATÉE, LE NUMÉRO DU MODÈLE ET LE NUMÉRO DE SÉRIE SONT OBLIGATOIRES POUR BÉNÉFICIER DE LA COUVERTURE OFFERTE PAR LA GARANTIE.