Download Print this page

NEC GT5000 - XGA LCD Projector Control Commands page 12

Np115 : rs232 codes- projectors

Advertisement

LT30
:
firmware version 1.03 or later
NP4000:
firmware version 1.04 or later
NP4001:
firmware version 1.01 or later
NP62
:
firmware version 1.02 or later
======================================================================
5. Command Descriptions
----------------------------------------------------------------------
Precautions with Inscriptions:
(*1) Projector ID
It is the value when forwarding a factory.
This reflects the "Projector ID" that has been set to the projector.
(*2) Model code: "xxH" inscription
This will differ depending on the projector.
In case of MT/NP1000 series
In case of MT/NP3150 series
In case of MT/NP3250 series
In case of LT/LT80 series
In case of NP61, NP62 series
In case of NP216 series
In case of VT series
In case of NP600 series
In case of NP610 series
In case of NP2200 series
In case of M300 series
In case of P420 series
In case of GT series
In case of HT series
In case of WT series
In case of HT10 series
In case of LT180 series
In case of LT30 series
In case of NP60 series
In case of NP4000, 4100 series
In case of NP905/NP901W/VT800
(*3) Checksum: "CKS" inscription
This is the value of the lower 8 bits of the results calculated in byte units from all of the data up to the immediately
preceding data.
Example:
20H 81H 01H 60H 01H 00H 03H
+
+
+
+
+
+ = CKS
(*4) Response error number
This is the value of the error number at the time of an error.
See "NAK" of "6-2. Data portion of response".
(*5) Term "RGB" and "COMPUTER"
On the HT1100, VT770, LT245/ LT265/ LT280/ LT380, NP1000/NP2000, NP1150/NP2150/NP3150/NP3151W,
NP1250/NP2250/NP3250/NP3250W, NP1200/NP2200, NP4000/NP4001, NP4100/NP4100W,
NP905/NP901W/VT800, LT25/LT30/LT35, VT48/VT480/VT580, VT49/VT490/VT590/VT595/VT695/VT700,
NP300/NP400/NP500/NP500W/NP500WS/NP600/NP600S,
NP310/NP410/MP410W/NP510/NP510W/NP610WS/NP610/NP610S,
NP40/NP50/NP60/NP41/NP61/NP62/NP43/NP64 and P350X/350W/420X, the term "RGB connector" has been
changed to "COMPUTER".
(*6) Term "DVI" and "COMPUTER"
On the LT380, NP1000/NP2000, NP1150/NP2150/NP3150/NP3151W, NP1250/NP2250/NP3250/NP3250W,
NP1200/NP2200, NP4000/NP4001, NP4100/NP4100W,
NP300/NP400/NP500/NP500W/NP500WS/NP600/NP600S,
10H
10H
10H
20H
20H
20H
40H
40H
40H
40H
40H
40H
50H
60H
70H
D0H
D0H
D0H
D0H
80H
90H

Advertisement

loading

This manual is also suitable for:

Gt6000Gt6000r - sxga+ lcd projectorHt510 - dlp projector - 1000 ansi lumensLt20eLt245Lt265 - xga dlp projector ... Show all