Precautions; Disclaimer Of Liability; Warning Label; Regulatory Information - Fujitsu ScanSnap N1800 Getting Started Manual

When carrying the scanner outside while it is
raining or snowing, pay special attention so the
scanner does not get wet.
When you perform cleaning, make sure that the
inside of the scanner is free of any foreign
objects, and be careful not to get your hand or
the cloth caught on the pick spring (metal part) as
a deformed pick spring (metal part) may cause
injury.

■ Precautions

READ ALL OF THIS DOCUMENT AND THE
OPERATOR'S GUIDE CAREFULLY BEFORE USING
THIS SCANNER. IF THIS SCANNER IS NOT USED
CORRECTLY, UNEXPECTED INJURY MAY BE
CAUSED TO USERS OR BYSTANDERS.
Also, keep this document in a safe place so that it can be
easily referred to during use of this scanner.
While all efforts have been made to ensure the accuracy
of all information in this document, PFU assumes no
liability to any party for any damage caused by errors or
omissions or by statements of any kind in this document,
its updates or supplements, whether such errors are
omissions or statements resulting from negligence,
accidents, or any other cause.
PFU further assumes no liability arising from the
application or use of any scanner or system described
herein; nor any liability for incidental or consequential
damages arising from the use of this document. PFU
disclaims all warranties regarding the information
contained herein, whether expressed, implied, or
statutory.
Use of Mercury
Lamp(s) inside the scanner contain mercury
H
g and must be recycled or disposed of
according to local, state, or federal laws.
To avoid unexpected injuries:
Do not put the substance contained in the lamp in your
mouth as it has mercury.
Do not breathe the chemical liquid contained in the
scanner lamps.
Do not incinerate, crush, or shred the lamps or
scanner parts.
LCD Peculiarities
The LCD backlight is a fluorescent tube that contains
some mercury.
Be aware that neither of the following is considered a
fault.
- Despite the advanced technologies used to produce
the devices TFT color LCD's, the large number of
pixels involved means that an occasional (always-
on) bright dot or (always-off) dark dot may be visible.
- The characteristics of the LCD mean that there may
be some variation in hue and intensity of colors
across the screen.
Replacing Batteries
In order to retain data such as BIOS information, this
product has a battery (CMOS RAM battery) on board.
ARNI N G

Warning Label

The scanner carries the warning label.
Do not remove the warning label from the scanner. Avoid
staining the label, so that it is clearly visible.

■ Disclaimer of Liability

Reproducibility of the Scanned Image
Data
Confirm that the image data scanned with this product
meets your requirements (for example, image
reproducibility in size accuracy, fidelity, content, colors).
Make sure that there are no missing parts in the scanned
image data before disposing of the original document
used for scanning.
Note that when there are sections marked with a
highlight pen, the color of the marked section may not
be accurately reproduced depending on the color and
density, or may result in a different color tone from the
original.

■ Regulatory Information

FCC Declaration
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction document, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
6
Do not replace the battery yourself,
as there is a risk of explosion if the
wrong type is used. Please contact
your maintenance engineer in
charge when the battery runs low.
Do not touch the battery. Never
install or remove the battery by
yourself. Doing so may cause
electric shock or static electricity
which can damage the device.