Table of Contents
Advertisement
-O
-O
Z
X
12.
13.
14.
15.
16.
OSD Select
(Command:
k I)
To select OSD (On Screen Display) on/off.
Transmission[k] [I][][Set!D][ ][Data][Cr]
Data 00: OSD
off
Data 01 :OSD
on
Acknowledgement[I]
[] [Set ID] [] [OK/NG]
[Data] [x]
Remote
Control
Lock Mode
(Command:
k m)
To lock the remote control
and the front panel controls
on the set.
Transmission [k] [m][]
[Set iD] [ ] [Data] [Cr]
Data 00: Lock off
Data 01 : Lock on
Acknowledgement[m][]
[set ID] [ ] [OK/NG]
[Data] [x]
If you're
not using the remote control
and front
panel
controls
on the TV, use this mode. When main power is
on/off,
remote control lock is released.
Treble
(Command:
k r)
To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission [k] [r][]
[Set ID] [ ] [Data] [Cr]
Data Min: O0 - Max: 64 (*transmit
by Hexadecimal code)
_Refer to 'Real data mapping' as shown.
Acknowledgement [r][]
[set ID] []
[OKiNG]
[Data] [x]
Bass (Command:
k s)
To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission
[k] [s] [ ] [Set ID] [ ] [Data] [Cr]
Data Min: O0 - Max: 64 (*transmit
by Hexadecimal code)
*Refer to 'Real data mapping' as shown.
Acknowledgemen_ [s] [ ] [Set ID] [ ] [OK/NG]
[Data] [x]
Balance
(Command:
k t)
To adjust balance.
You can also adjust balance in the AUDIO menu.
TransmissiOn [k] [t][]
[set ID] []
[Data] [Cr]
Data Min: O0 - Max: 64 (*transmit
by Hexadecimal code)
*Refer to 'Real data mapping' as shown.
Acknowledgement [t][
][set
ID][
] [OKiNG]
[Data] [x]
1 8. Auto
Configuration
(Command:
j u)
To adjust picture
position
and minimize image shaking
automatically.
Auto configuration
only works in RGB-PC
mode.
Transmission [i]
[u][]
[Set !D] [ ] [Data] [Cr]
Data 01 : To set
Acknowledgemen_ [u][]
[Set ID] [ ] [OK/NG]
[Data] [x]
*Real data mapping
0 : Step 0
A : Step 10 (SET ID 10)
F : Step 15 (SET ID 15)
10
Step 16 (SET ID 16)
63
Step 99 (SET ID 99)
64
Step 100
19. Channel
Tuning
(Command:
m a)
To tune channel to following physical/major/minor
number.
Transmission [m] [a][]
[Set iD][]
[Daiaoo]
[ ] [Data01]
[] [Data02]
[] [Data03]
[] [Data04]
[ ] [Data05]
[Cr]
Digital channels have a Physical, Major, and Minor channel
number. The Physical number is the actual digital channel
number, the Major is the number that the channel should
be mapped to, and the Minor is the sub-channel.
Since
the ATSC tuner automatically
maps the channel to the
Major number, the Physical number is not required when
sending a command.
Data 00: Physical Channel Number
NTSC air: 02-45,
NTSC cable: 01,0E-7D
ATSC air: 01-45,
ATSC cable: 01-87
Data 01 & 02: Major Channel Number
Data 01 : High byte
Data 02: Low byte
Two bytes are available for the Major and Minor, nor-
mally only the second byte is used.
Data 03 & 04: Minor Channel Number
Not needed for NTSC.
17.
Color Temperature
(Command:
k u)
To adjust color temperature.
You can also adjust color temperature in the PICTURE menu.
Transmission[k] [u][]
[set ID] [ ] [Data] [Cr]
Data 00: Medium
01: Cool
02: Warm
Acknowledgement[u]
[]
[Set ID] [] [OK/NG]
[Data] [x]
98
Advertisement
Table of Contents
