Pioneer 504CMX - PDP - 50" Plasma Panel Command Reference Manual page 8

5.5.5 List of RS-232C Commands
How to read this Table
• RS-232C adjustment validity : Indicates whether or not the RS-232C adjustment mode can be used.
• Normal validity
• Numerical direct validity
‡ ¶
• or : Valid, No mark: Invalid
¶
(NOTE) values are not stored in the last memory.
Command name AJY (232C integrator) Display
[A]
AJN –
AJY ADJUST: ON
AMN AUDIO MUTING: OFF
AMY AUDIO MUTING: ON
AST AUTO SET UP
[B]
B HIGH: ∗∗∗
BHI
B LOW: ∗∗∗
BLW
BRA BAUD RATE: #####-232C
BRAS01 BAUD RATE: 1200-232C
BRAS02 BAUD RATE: 2400-232C
BRAS03 BAUD RATE: 4800-232C
BRAS04 BAUD RATE: 9600-232C
BRAS05 BAUD RATE: 19200-232C
BRAS06 BAUD RATE: 38400-232C
BRIGHTNESS: ∗∗∗
BRT
B SIDE MASK LEVEL: ∗∗∗
BSL
[C]
CLOCK: ∗∗∗
CFR
COLOR DETAIL BLUE: ∗∗∗
CGB
COLOR DETAIL CYAN: ∗∗∗
CGC
COLOR DETAIL GREEN: ∗∗∗
CGG
COLOR DETAIL MAGENTA: ∗∗∗
CGM
COLOR DETAIL RED: ∗∗∗
CGR
COLOR DETAIL YELLOW: ∗∗∗
CGY
CLS COLOR SYSTEM: #####
CLSS01 COLOR SYSTEM: AUTO
CLSS02 COLOR SYSTEM: NTSC
CLSS03 COLOR SYSTEM: PAL
CLSS04 COLOR SYSTEM: SECAM
CLSS05 COLOR SYSTEM: 4.43NTSC
CLSS06 COLOR SYSTEM: PAL M
CLSS07 COLOR SYSTEM: PAL N
CM1 COLOR MODE: NORMAL
CM2 COLOR MODE: STUDIO
CONTRAST: ∗∗∗
CNT
COLOR OFF: ∗∗∗∗∗∗∗∗
COF
COFS00 COLOR OFF: DISABLE
COFS01 COLOR OFF: ENABLE
COLOR: ∗∗∗
COL
PHASE: ∗∗∗
CPH
COLOR TEMP.: ∗∗∗∗∗∗∗∗
CTP
CTPS01 COLOR TEMP.: LOW
CTPS02 COLOR TEMP.: MID LOW
CTPS03 COLOR TEMP.: MIDDLE
CTPS04 COLOR TEMP.: MID HIGH
CTPS05 COLOR TEMP.: HIGH
: Indicates whether or not the normal-operation mode can be used.
: When a number (3-digit number) is attached to the end of a command, the
command can directly set that adjustment value.
Terminates the 232C integrator adjustment mode.
Starts the 232C integrator adjustment mode.
Turns OFF the audio mute.
Turns ON the audio mute.
Executes AUTO SETUP.
Adjusts B. HIGH.
Adjusts B. LOW.
Displays the current baud rate.
Sets the UART setting to 232C (1200BPS).
Sets the UART setting to 232C (2400BPS).
Sets the UART setting to 232C (4800BPS).
Sets the UART setting to 232C (9600BPS).
Sets the UART setting to 232C (19200BPS).
Sets the UART setting to 232C (38400BPS).
Adjusts the brightness.
Adjusts the BLUE side mask.
Adjusts the CLOCK (PLL frequency).
Adjusts color detail BLUE.
Adjusts color detail CIAN.
Adjusts color detail GREEN.
Adjusts color detail MAGENTA.
Adjusts color detail RED.
Adjusts color detail YELLOW.
Displays the current color system.
Sets the color system to AUTO.
Sets the color system to NTSC.
Sets the color system to PAL.
Sets the color system to SECAM.
Sets the color system to 4.43NTSC
Sets the color system to PAL M.
Sets the color system to PAL N.
Sets the color mode to NORMAL.
Sets the color mode to STUDIO.
Adjusts the CONTRAST.
Displays the current COLOR OFF setting.
Disables COLOR OFF.
Enables COLOR OFF.
Adjusts the COLOR.
Adjusts the PHASE (PLL phase).
Displays the current COLOR TEMP.
Sets the COLOR TEMP. to LOW.
Sets the COLOR TEMP. to MID LOW.
Sets the COLOR TEMP. to MIDDLE.
Sets the COLOR TEMP. to MID HIGH.
Sets the COLOR TEMP. to HIGH.
RS-232C Adjustment Mode
Remarks
RS-232C Numerical
Normal
Adjustment Direct
Validity
Validity Validity
¶
¶
¶ ¶
¶ ¶
‡
‡ ‡
‡ ‡
¶
‡
‡
‡
‡
‡
‡
‡ ‡
‡ ‡
‡ ‡
‡ ‡
‡ ‡
‡ ‡
‡ ‡
‡ ‡
‡ ‡
¶
‡
‡
‡
‡
‡
‡
‡
‡ ‡
‡ ‡
‡ ‡
¶
‡
‡
‡ ‡
‡ ‡
¶
‡
‡
‡
‡
‡
6