Page 1
Read this manual carefully before operating this vehicle. OWNER’S MANUAL YZFR6Z(C) LIT-11626-23-68 13S-28199-12...
Page 2
EAU10042 Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
Page 3
Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.
IMPORTANT MANUAL INFORMATION EAU10132 Particularly important information is distinguished in this manual by the following notations: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
TABLE OF CONTENTS LOCATION OF IMPORTANT Luggage strap holders ....4-24 Checking the throttle cable free LABELS ..........1-1 EXUP system ....... 4-24 play ........... 7-21 Sidestand ........4-25 Valve clearance ......7-21 SAFETY INFORMATION ....2-1 Ignition circuit cut-off system ..4-25 Tires ..........
Page 7
STREET AND ENDURO Replacing a headlight bulb ...7-37 MOTORCYCLE LIMITED Tail/brake light ......7-38 WARRANTY ......10-7 Replacing a turn signal light YAMAHA EXTENDED SERVICE bulb ...........7-38 (Y.E.S.) ........10-9 Replacing the license plate light bulb ...........7-39 Supporting the motorcycle ....7-40 Front wheel ........7-40...
Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
Page 9
LOCATION OF IMPORTANT LABELS WARNING NOTICE Cleaning with alkaline or BEFORE YOU OPERATE THIS VEHICLE, READ acid cleaner, gasoline or THE OWNER’S MANUAL AND ALL LABELS. solvent will damage ALWAYS WEAR AN APPROVED MOTORCYCLE windshield. HELMET, eye protection, and protectibe clothing. Use neutral detergent.
Page 11
LOCATION OF IMPORTANT LABELS 1 California only 2 California only HOW TO LAYOUT FUEL HOSES FUEL TANK CHARCOAL CANISTER FUEL PUMP FUEL FILTER FUEL DELIVERY PRESS. REGULATOR 13S-21686-10 13S-2178A-10 3 California only 13S-21684-10...
SAFETY INFORMATION EAU10283 Safe Riding • Ride where other motorists can Perform the pre-operation checks each see you. Avoid riding in another time you use the vehicle to make sure it motorist’s blind spot. Be a Responsible Owner is in safe operating condition. Failure to Many accidents involve inexperi- As the vehicle’s owner, you are respon- inspect or maintain the vehicle properly...
Page 13
SAFETY INFORMATION due to excessive speed or under- This motorcycle is designed for on- A passenger should also observe cornering (insufficient lean angle road use only. It is not suitable for the above precautions. for the speed). off-road use. • Always obey the speed limit and Avoid Carbon Monoxide Poisoning never travel faster than warrant- Protective apparel...
Page 14
Yamaha accessories, which are avail- of the motorcycle is changed. To avoid to minimize imbalance or instabili- able only from a Yamaha dealer, have the possibility of an accident, use ex- been designed, tested, and approved treme caution when adding cargo or Shifting weights can create a sud- by Yamaha for use on your vehicle.
• Accessories fitted to the handle- Use caution when adding electri- genuine Yamaha accessories, recog- bar or the front fork area can cal accessories. If electrical acces- nize that some aftermarket accessories...
INSTRUMENT AND CONTROL FUNCTIONS EAU10460 EAU10661 To lock the steering Main switch/steering lock All electrical systems are off. The key can be removed. EWA10061 WARNING Never turn the key to “OFF” or “LOCK” while the vehicle is moving. Otherwise the electrical systems will be switched off, which may result in loss of control or an accident.
9. Engine trouble warning light “ ” initially when the key is turned to “ON”, or if the warning light remains on, have EAU11030 a Yamaha dealer check the electrical Turn signal indicator lights “ ” circuit. and “ ”...
Page 21
3.0 seconds. If this oc- have a Yamaha dealer check the the coolant temperature in the ra- curs, have a Yamaha dealer check the vehicle. diator. vehicle. If the engine overheats, see page 7-45 for further instructions.
Page 22
INSTRUMENT AND CONTROL FUNCTIONS Coolant Display Conditions What to do temperature TRIP A Under 39 °C ˚F Message “Lo” is displayed. OK. Go ahead with riding. (Under 103 °F) TRIP A 40–116 °C ˚F Temperature is displayed. OK. Go ahead with riding. (104–242 °F) Stop the vehicle and allow it to idle until TRIP A...
If this occurs, go off. have a Yamaha dealer check the self- If the indicator light does not come on diagnosis system. (See page 4-8 for an TRIP A ˚F...
Page 24
INSTRUMENT AND CONTROL FUNCTIONS multi-function meter unit To switch the speedometer and ECA10031 NOTICE equipped with the following: odometer/tripmeter displays be- a speedometer tween kilometers and miles, press Do not operate the engine in the ta- a tachometer the “SELECT” button for at least chometer red zone.
Page 25
INSTRUMENT AND CONTROL FUNCTIONS 5. Push the “RESET” button to set serve tripmeter mode “F-TRIP” and Standard measurement the minutes. start counting the distance traveled 1. Push the “RESET” button to start 6. Push the “SELECT” button and from that point. In that case, push the the stopwatch.
Page 26
If the right display indicates any error the coolant temperature is auto- codes, note the code number, and then matically displayed, even if the air have a Yamaha dealer check the vehi- intake temperature was displayed cle. prior to turning the key to “OFF”.
Page 27
INSTRUMENT AND CONTROL FUNCTIONS ECA11590 Display brightness: NOTICE This function allows you to adjust In this mode, the right display shows If the display indicates an error the brightness of the displays and the current setting for each function tachometer to suit the outside code, the vehicle should be checked (except the shift timing indicator light lighting conditions.
Page 28
INSTRUMENT AND CONTROL FUNCTIONS The indicator light will stay on can be set in increments of 500 r/min. Be sure to set the deactivation when activated. (This setting From 13000 r/min to 18000 r/min, the function to a higher engine speed is selected when the indicator indicator light can be set in increments than for the activation function,...
INSTRUMENT AND CONTROL FUNCTIONS EAU12348 EAU12400 EAU12711 Handlebar switches Dimmer switch “ ” Start switch “ ” Set this switch to “ ” for the high Push this switch to crank the engine Left beam and to “ ” for the low beam. with the starter.
INSTRUMENT AND CONTROL FUNCTIONS EAU12820 EAU12870 EAU33851 Clutch lever Shift pedal Brake lever 1. Clutch lever 1. Shift pedal 1. Brake lever 2. Distance between brake lever and handlebar The clutch lever is located at the left The shift pedal is located on the left grip handlebar grip.
INSTRUMENT AND CONTROL FUNCTIONS be sure to set it by aligning a groove on EAU12941 EAU13074 Brake pedal Fuel tank cap the adjusting knob with the “ ” mark on the brake lever. 1. Brake pedal 1. Fuel tank cap lock cover 2.
INSTRUMENT AND CONTROL FUNCTIONS EAU13221 Fuel The fuel tank cap cannot be closed un- Make sure there is sufficient gasoline in less the key is in the lock. In addition, the tank. the key cannot be removed if the cap is EWA10881 WARNING not properly closed and locked.
Check the fuel tank breather/over- as well as to the exhaust system. flow hose for cracks or damage, Your Yamaha engine has been de- and replace it if damaged. signed to use premium unleaded gaso- Make sure that the end of the fuel...
INSTRUMENT AND CONTROL FUNCTIONS EAU13445 ECA10701 EAU39032 Catalytic converters Seats NOTICE This vehicle is equipped with catalytic Use only unleaded gasoline. The use converters in the exhaust system. Rider seat of leaded gasoline will cause unre- EWA10862 pairable damage to the catalytic WARNING To remove the rider seat converter.
Page 35
INSTRUMENT AND CONTROL FUNCTIONS 1. Projection 1. Passenger seat lock 1. Projection 2. Seat holder 2. Unlock. 2. Seat holder 2. While holding the key in that posi- 2. Remove the key. Passenger seat tion, lift the front of the passenger seat and pull it forward.
INSTRUMENT AND CONTROL FUNCTIONS EAU39073 3. Pass one of the other snap hooks Helmet holding cable of the cable through the helmet strap buckle, and then clip the snap hook onto the cable holder as shown. 1. Helmet holding cable 2.
INSTRUMENT AND CONTROL FUNCTIONS EAU39671 EAU38943 Spring preload Rear view mirrors Adjusting the front fork The rear view mirrors of this vehicle can EWA10180 WARNING be folded forward or backward for park- ing in narrow spaces. Fold the mirrors Always adjust both fork legs equal- back to their original position before ly, otherwise poor handling and loss riding.
Page 38
INSTRUMENT AND CONTROL FUNCTIONS Rebound damping force Compression damping force To adjust the compression damping force (for fast compression damping) 1. Current setting 2. Front fork collar 1. Rebound damping force adjusting screw To increase the rebound damping force Spring preload setting: and thereby harden the rebound damp- Minimum (soft): 1.
INSTRUMENT AND CONTROL FUNCTIONS and thereby soften the compression EAU42944 Compression damping setting (for Adjusting the shock absorber damping, turn the adjusting bolt on fast compression damping): assembly each fork leg in direction (b). Minimum (soft): This shock absorber assembly is 4 turn(s) in direction (b)* Standard: equipped with a spring preload adjust-...
Page 40
INSTRUMENT AND CONTROL FUNCTIONS Spring preload Spring preload setting: Rebound damping setting: Minimum (soft): Minimum (soft): 20 click(s) in direction (b)* Standard: Standard: 16 click(s) in direction (b)* Maximum (hard): Maximum (hard): 3 click(s) in direction (b)* * With the adjusting screw fully turned in direction (a) Rebound damping force Compression damping force...
Page 41
Take the shock adjusting mechanism. This adjustment absorber assembly to a Yamaha range may not exactly match the spec- dealer for any service. ifications listed due to small differences in production.
EAU41941 Luggage strap holders EXUP system passenger seat, unhook the straps This model is equipped with Yamaha’s from the hooks, and then install the EXUP (EXhaust Ultimate Power valve) seat with the straps hanging out from system. This system boosts engine under the passenger seat.
INSTRUMENT AND CONTROL FUNCTIONS EAU15303 below and have a Yamaha dealer re- EAU44892 Sidestand Ignition circuit cut-off system pair it if it does not function proper- The sidestand is located on the left side The ignition circuit cut-off system (com- of the frame.
Page 44
INSTRUMENT AND CONTROL FUNCTIONS WARNING With the engine turned off: 1. Move the sidestand down. If a malfunction is noted, have a Yamaha 2. Make sure that the engine stop switch is set to “ ”. dealer check the system before riding.
• If necessary, add recommended coolant to specified level. 7-17 • Check cooling system for leakage. • Check operation. • If soft or spongy, have Yamaha dealer bleed hydraulic system. • Check brake pads for wear. Front brake • Replace if necessary.
Page 46
• Make sure that operation is smooth. • Check cable free play. Throttle grip 7-21, 7-31 • If necessary, have Yamaha dealer adjust cable free play and lubricate cable and grip housing. • Make sure that operation is smooth. Control cables 7-30 •...
Page 47
• Tighten if necessary. Instruments, lights, signals • Check operation. — and switches • Correct if necessary. • Check operation of ignition circuit cut-off system. Sidestand switch 4-25 • If system is not working correctly, have Yamaha dealer check vehicle.
(See page 6-2.) The with the engine off, and do not neutral indicator light should come tow the motorcycle for long dis- on. If not, ask a Yamaha dealer to tances. The transmission is check the electrical circuit. properly lubricated only when 3.
OPERATION AND IMPORTANT RIDING POINTS 4. At the recommended shift points 3. Shift the transmission into the neu- EAU16841 Engine break-in shown in the following table, close tral position when the motorcycle There is never a more important period the throttle, and at the same time, is almost completely stopped.
(if applicable). Yamaha your risk of injury or death during dealers are trained and equipped to service or while using the vehicle. If perform these particular services.
From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months. Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service. EAU17601...
Page 55
PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months Evaporative emis-...
PERIODIC MAINTENANCE AND ADJUSTMENT EAU32186 General maintenance and lubrication chart INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months...
Page 57
PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months •...
Page 58
24 months. Front and rear brake √ √ √ √ √ √ 25 * • Check operation. switches • Apply Yamaha chain and cable √ √ √ √ √ √ 26 * Control cables lube or engine oil thoroughly.
Page 59
PERIODIC MAINTENANCE AND ADJUSTMENT INITIAL ODOMETER READINGS 600 mi 4000 mi 8000 mi 12000 mi 16000 mi 20000 mi ITEM ROUTINE (1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km) 1 month 6 months 12 months 18 months 24 months 30 months •...
PERIODIC MAINTENANCE AND ADJUSTMENT EAU18712 EAU44931 Removing and installing cowl- Cowlings A and B ings and panels To remove one of the cowlings The cowlings and panels shown need 1. Remove the bolts, quick fasteners, to be removed to perform some of the and quick fastener screw.
Page 61
PERIODIC MAINTENANCE AND ADJUSTMENT 1. Quick fastener 1. Quick fastener 1. Cowling A 2. Quick fastener screw 2. Cowling B 3. Remove the forward-most projec- tion from the slot, slide the cowling forward, and then remove the re- maining projections from the slots as shown.
Page 62
PERIODIC MAINTENANCE AND ADJUSTMENT 2. Fit the projections into the slots, 3. Fit the projection on cowling A into slide the cowling rearward, and the hole in cowling B as shown. then fit the forward-most projection into the slot. 1. Cowling A 2.
Page 63
PERIODIC MAINTENANCE AND ADJUSTMENT To install the cowling 1. Fit the slot in cowling C over the projection on the front cowling. 1. Plastic fastener 1. Panel B 2. Projection 2. Bolt 3. Wire harness To install the panel 1. Cowling C 3.
Do not attempt to diagnose wipe off any grime from the spark plug such problems yourself. Instead, have threads. a Yamaha dealer check the vehicle. If a spark plug shows signs of electrode Tightening torque: Spark plug: erosion and excessive carbon or other 13 Nm (1.3 m·kgf, 9.4 ft·lbf)
PERIODIC MAINTENANCE AND ADJUSTMENT EAU19681 EAU3899A Canister (for California only) Engine oil and oil filter car- tridge The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter car- tridge replaced at the intervals speci- fied in the periodic maintenance and lubrication chart.
Page 66
PERIODIC MAINTENANCE AND ADJUSTMENT 6. Insert and tighten the engine oil dipstick, and then install and tight- en the oil filler cap. To change the engine oil (with or without oil filter cartridge replace- ment) 1. Place the vehicle on a level sur- face.
Page 67
An oil filter wrench is available at a [ECA15342] Yamaha dealer. 9. Apply a thin coat of clean engine oil to the O-ring of the new oil filter cartridge.
(since the engine oil also off and have a Yamaha dealer check 2. Check the coolant level in the cool- lubricates the clutch), do not the vehicle.
Page 69
2. Remove cowlings B and C. (See corrosion. If water has been page 7-9.) added to the coolant, have a 3. Place a container under the engine Yamaha dealer check the anti- to collect the used coolant. freeze content of the coolant as 4. Remove radiator cap.
Page 70
PERIODIC MAINTENANCE AND ADJUSTMENT 6. Move the hose clamp in the direc- 13. Pour the recommended coolant tion shown, and then disconnect into the reservoir to the maximum the radiator hose to drain the radi- level mark, and then install the ator.
Check the engine idling speed and, if dealer check the cooling system. maintenance and lubrication chart. necessary, have it corrected by a 18. Install the cowlings. Have a Yamaha dealer replace the air Yamaha dealer. filter element. Engine idling speed: 1250–1350 r/min...
To prevent this cle, note the following points regarding from occurring, the valve clearance the specified tires. must be adjusted by a Yamaha dealer at the intervals specified in the periodic Tire air pressure maintenance and lubrication chart.
Page 73
* Total weight of rider, passenger, car- if the tire has a nail or glass fragments go and accessories in it, or if the sidewall is cracked, con- tact a Yamaha dealer immediately and EWA10511 WARNING have the tire replaced.
Page 74
Yamaha Motor Co., Ltd. Use only the specified replace- ment tires. Other tires may run the danger of bursting at super high speeds.
If any damage is 2. Loosen the locknut at the crank- found, have a Yamaha dealer re- case. place the wheel. Do not attempt 3. To increase the clutch lever free...
1. No brake lever free play There should be no free play at the brake lever end. If there is free play, have a Yamaha dealer inspect the brake system. EWA14211 WARNING A soft or spongy feeling in the brake lever can indicate the presence of air in the hydraulic system.
Brake light switches Checking the front and rear touches the brake disc, have a Yamaha brake pads dealer replace the brake pads as a set. The front and rear brake pads must be...
However, if the Use only the recommended quality brake fluid level goes down sud- 1. Minimum level mark brake fluid, otherwise the rubber denly, have a Yamaha dealer Rear brake seals may deteriorate, causing check the cause. leakage and poor braking perfor- mance.
EAU22731 EAU22760 Changing the brake fluid Drive chain slack Have a Yamaha dealer change the The drive chain slack should be brake fluid at the intervals specified in checked before each ride and adjusted the TIP after the periodic maintenance if necessary.
Page 80
PERIODIC MAINTENANCE AND ADJUSTMENT To prevent this from occurring, Tightening torque: keep the drive chain slack with- Locknut: in the specified limits. 16 Nm (1.6 m·kgf, 12 ft·lbf) [ECA10571] Using the alignment marks on each drive chain puller, make sure that both chain pullers are in the same position for proper wheel alignment.
If a cable is damaged wet areas. Service the drive chain as or does not move smoothly, have a follows. Yamaha dealer check or replace it. WARNING! Damage to the outer ECA10583 NOTICE housing of cables may result in in-...
The operation of the throttle grip should Brake pedal be checked before each ride. In addi- tion, the cable should be lubricated by a Yamaha dealer at the intervals speci- fied in the periodic maintenance chart. Shift pedal The operation of the brake and shift...
EWA10731 WARNING If the sidestand does not move up and down smoothly, have a Yamaha dealer check or repair it. Otherwise, the sidestand could contact the ground and distract the operator, re- The operation of the brake and clutch sulting in a possible loss of control.
The swingarm pivots must be lubricat- face and hold it in an upright posi- fork does not operate smoothly, ed by a Yamaha dealer at the intervals tion. WARNING! To avoid injury, have a Yamaha dealer check or re- specified in the periodic maintenance securely support the vehicle so pair it.
If any free lyte or to add distilled water. However, the wheel bearings. play can be felt, have a Yamaha the battery lead connections need to be dealer check or repair the steering. checked and, if necessary, tightened.
Page 86
[ECA16302] To charge the battery 2. If the battery will be stored for more Have a Yamaha dealer charge the bat- than two months, check it at least tery as soon as possible if it seems to once a month and fully charge it if have discharged.
4. If the fuse immediately blows 6. Electronic throttle valve fuse 2. Remove the blown fuse, and then again, have a Yamaha dealer 7. Spare fuse install a new fuse of the specified check the electrical system.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU39012 Replacing a headlight bulb This model is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. ECA10650 NOTICE Take care not to damage the follow- ing parts: Headlight bulb 1.
Replacing a turn signal light turning it clockwise. bulb This model is equipped with an LED- 7. Have a Yamaha dealer adjust the type tail/brake light. 1. Remove the turn signal light lens headlight beam if necessary. If the tail/brake light does not come on, by removing the screw.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU24313 Replacing the license plate light bulb 1. Remove the license plate light unit by removing the screws. 1. Turn signal light bulb 1. License plate light bulb 2. License plate light unit 3. Insert a new bulb into the socket, 3.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU24350 a jack either under each side of the EAU24360 Supporting the motorcycle Front wheel frame in front of the rear wheel or under Since this model is not equipped with a each side of the swingarm. centerstand, follow these precautions EAU34594 To remove the front wheel...
PERIODIC MAINTENANCE AND ADJUSTMENT 3. Remove the brake hose holder Tightening torque: and reflector on each side by re- Brake caliper bolt: moving the bolt and nut. 35 Nm (3.5 m·kgf, 25 ft·lbf) 4. Remove the brake caliper on each 5.
PERIODIC MAINTENANCE AND ADJUSTMENT EAU25080 Tightening torque: Rear wheel Wheel axle pinch bolt: 21 Nm (2.1 m·kgf, 15 ft·lbf) EAU44951 To remove the rear wheel 12. While applying the front brake, EWA10821 push down hard on the handlebar WARNING several times to check for proper To avoid injury, securely support the fork operation.
Page 94
PERIODIC MAINTENANCE AND ADJUSTMENT 4. Loosen the locknut on each side of 7. While supporting the brake caliper Make sure that there is enough the swingarm. bracket, pull the wheel axle out, space between the brake pads be- 5. Turn the drive chain slack adjust- and then remove the wheel.
However, should your motorcycle Tightening torque: require any repair, take it to a Yamaha Drive chain slack adjusting bolt: dealer, whose skilled technicians have 2.0 Nm (0.20 m·kgf, 1.4 ft·lbf) the necessary tools, experience, and 7.
Remove the spark plugs and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the battery. 4. Battery The engine turns over The battery is good.
Page 97
Start the engine. If the engine overheats again, have a The coolant level Yamaha dealer check and repair the cooling system. is OK. If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant as soon as possible.
Be ble. Rust and corrosion can develop Cleaning even if high-quality components are sure to consult a Yamaha dealer for ECA11142 used. A rusty exhaust pipe may go un- advice on what products to use be-...
Page 99
MOTORCYCLE CARE AND STORAGE off any detergent residue using pounds for plastic may leave plenty of water, as it is harmful scratches on the windshield. Salt sprayed on roads in the winter may to plastic parts. Test the product on a small hid- remain well into spring.
Page 100
WARNING muffler is normal and cannot be re- moved. Contaminants on the brakes or tires Consult a Yamaha dealer for ad- can cause loss of control. vice on what products to use. After cleaning Make sure that there is no oil or Washing, rainy weather or humid 1.
MOTORCYCLE CARE AND STORAGE EAU26181 3. Perform the following steps to pro- 4. Lubricate all control cables and the Storage tect the cylinders, piston rings, etc. pivoting points of all levers and from corrosion. pedals as well as of the side- Short-term a.
Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen. KEY IDENTIFICATION NUMBER: 1.
Page 106
This informa- illustration. This label shows specifica- tion will be needed when ordering tions related to exhaust emissions as spare parts from a Yamaha dealer. required by federal law, state law and Environment Canada. 10-2...
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation, U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
CONSUMER INFORMATION EAU26560 Motorcycle noise regulation TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve- hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
CONSUMER INFORMATION EAU26632 Maintenance record Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required.
Page 110
CONSUMER INFORMATION Maintenance Date of Servicing dealer Mileage Remarks interval service name and address 36000 mi (55000 km) or 54 months 40000 mi (61000 km) or 60 months 10-6...
CONSUMER INFORMATION EAU26663 YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY Yamaha Motor Corporation, U.S.A. hereby warrants that CUSTOMER’S RESPONSIBILITY under this Engine Period new Yamaha motorcycles will be free from defects in warranty shall be to: Displacement...
Page 112
CUSTOMER SERVICE What costs are my responsibility during the warranty period? If your machine requires warranty service, you must take it to any authorized Yamaha The customer’s responsibility includes all costs of normal maintenance services, motorcycle dealer within the continental United States. Be sure to bring your warranty non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, registration card or other valid proof of the original date of purchase.
This excellent Y.E.S. plan coverage is only available to dealer to see how comforting uninterrupted factory- Yamaha owners like you, and only while your Yamaha is still backed protection can be. within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts.
Page 114
Yamaha Limited Warranty expires. A special note: If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.
Page 115
INDEX Engine trouble warning light ....4-5 Multi-function meter unit ......4-5 EXUP system ........4-24 Air filter element........7-20 Neutral indicator light ......4-2 Front and rear brake pads, checking ..7-26 Noise regulation........10-4 Battery ..........7-34 Front fork, adjusting ......4-19 Brake and clutch levers, checking and Front fork, checking.......7-33 lubricating ...........
Page 116
INDEX Tires ............7-21 Tool kit ............ 7-2 Troubleshooting ........7-44 Troubleshooting charts ......7-45 Turn signal indicator lights ...... 4-2 Turn signal light bulb, replacing .... 7-38 Turn signal switch ......... 4-11 Valve clearance ........7-21 Vehicle Emission Control Information label ............
Page 118
YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2009.10-0.3×1 CR...