Table of Contents
Advertisement
Operator's
Manual
CRI:IF
MRN°I
X E
12-Volt Lithium-Ion Cordless
Multi-Tool
Model No. 320.61199
c_ius
LISTED
_k WARNING:
To reduce the risk of
injury, the user must read and understand
the Operator's
manual before using
this product.
• Warranty
• Safety
• Assembly
• Operation
• Maintenance
Charge
battery
Before
first use
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.craftsman.com
Advertisement
Table of Contents
Related Manuals for Craftsman Nextec 320.61199
Summary of Contents for Craftsman Nextec 320.61199
- Page 1 To reduce the risk of • Assembly injury, the user must read and understand • Operation the Operator's manual before using • Maintenance this product. Charge battery Before first use Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.craftsman.com...
- Page 2 If this Craftsman tool fails to give complete satisfaction within one year from the date of purchase, return it to any Sears store or Parts & Repair Center or other Craftsman outlet in the United States for free repair (or replacement, if repair proves impossible).
-
Page 3: Safety Symbols
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention... - Page 4 Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles...
-
Page 5: General Safety Rules
GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. The term "power tool" in all of warnings listed below refers to corded power tools or battery-operated (cordless) power tools. -
Page 6: Personal Safety
PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. - Page 7 POWER TOOL USE AND CARE Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and more safely at the rate for which it was designated. Do not use the power tool if the switch does not turn it ON and OFF. Any power tool that cannot be controlled with the switch is dangerous...
- Page 8 BATTERY TOOL USE AND CARE • Make sure that the switch is in the OFF position before inserting the battery pack. Inserting the battery pack into power tools that have the switch invites accidents. Recharge only with the charger specified by the manufacturer.
- Page 9 • Exercise extreme caution when handling the scraper accessory. accessory is very sharp; danger of injury. • Use only the original Craftsman accessories and the other accessories (Fein and Rockwell Multi-Tool Accessories) available for this Mulit-Tool, no others.
- Page 10 • Only use application accessories in good condition. Do not use them if they are torn or worn. • Do not restart a cutting operation in the workpiece. To resume a cutting operation: while keeping the tool from contacting the workpiece, allow the tool reach full speed and then carefully guide the cutting accessory into the cut.
- Page 11 • Keep the cord and charger from heat to prevent damage to housing or internal parts. • Do not allow gasoline, oils, petroleum-based products, etc. to come in contact with plastic parts. These materials contain chemicals that can damage, weaken, or destroy plastic.
-
Page 12: Important Safety Instructions
IM PORTANT SAFETY INSTRUCTIONS • Save these instructions. This manual contains important safety and operating instructions for 12V Multi-Tool 320.61199. • Before using the ,battery charger, read all instructions and cautionary markings on battery charger, the battery and the product using battery, as well as the operator's manuals for these products. - Page 13 ID]=_.'_o_[[o_] KNOW YOUR MULTI-TOOL (Fig.l) PRODUCT SEPCIFICATION Motor 12 Volt DC Tool Weight (with battery) 1.81bs Oscillation Rate 15000/Min Oscillation Angle _+1.4degrees Battery Type Lithium-Ion Battery Voltage 12 Volt DC Charger Input 120-Volts, 60 Hz AC only Optimum Charging Temperature 32°F (0 °...
-
Page 14: Packing List
• If any part is damaged or missing, please refer to the numbers listed on the back page of operator's manual. PACKING LIST Multi-Tool, straight edge flush cut blade, circular saw blade, hardened steel scraping blade, carbide circular adhesive removal blade, carbide triangular rasp, sanding plate and 24 pcs sandpapers, hex key, vacuum adaptor, operator's manual. -
Page 15: Battery Protection
BATTERY PROTECTION). BATTERY PROTECTION The battery circuitry protects the battery pack from extreme temperature, over discharge, and over-charge. To protect the battery from damage and prolong its life, the battery pack circuitry will turn off the battery pack if it becomes overloaded or if the temperature becomes... - Page 16 HOW TO CHARGE THE BATTERY PACK NOTE: This Lithium-ion battery pack is shipped partially charged. Before using it the first time, fully charge the battery pack. A fully discharged battery pack will charge in about 30 minutes in an environment between 32 °...
- Page 17 CHARGING A HOT BATTERY PACK If the battery pack is above normal temperature range, the red LED will illuminate and the green LED will be off. When the battery pack cools down to approximately 104°F (40°C), the charger will automatically begin charging.
-
Page 18: Assembly
TO DETACH BATTERY Fig. 4 PACK (Fig. 4) Make sure that the tool is "OFF" Depress the battery release buttons located on the both sides of th of the battery pack to release the battery pack. Pull the battery pack out and remove it from the tool. -
Page 19: Application
DETACHABLE VACUUM Fig. 7 ADAPTOR (Fig.7) Always connect the vacuum adaptor when sanding. Remove the application tool before mounting the vacuum adaptor. To improve dust extraction from the working area, insert the dust-extraction adaptor into the rear of the tool, and connect the adaptor to a dust-extraction... - Page 20 Fig. 8 Fig. 9 Fig. 10 Ribs on shaft Grooves Fig. 11 90 _ 240' 270' 300' 330' 180' MOUNTING/CHANGING THE SANDPAPER (Fig.12) A_, WARNING: Failure to remove the battery pack from the tool when assembling parts, making adjustments, or changing accessories could result in accidental...
- Page 21 SAWING Fig. 13 & WARNING: Use sharp, undamaged saw blades only. Deformed, blunt saw blades or saw blades that are otherwise damaged can break. WARNING: When sawing light building materials, observe the statutory provisions the recommendations of the material suppliers. WARNING: Plunge cuts may only be applied to soft...
- Page 22 SANDING WARNING: Do not touch the gear box after prolonged use; it could be very hot. • The removal rate and the sanding pattern are determined by the choice of sanding sheet and the work surface. • Apply uniform sanding pressure to extend the life of the sanding sheets.
- Page 23 r:1-,J -,J al[t]_aiil[,)_i ACCESSORY APPLI CATION Carbide Circular Cut out the grout around tile Adhesive Removal Blade Remove tile adhesive residue Carbide Triangular Rasp Hardened Steel Remove floor coverings Scraping Blade scrape off adhesive residue Cut and remove the damaged part of plasterboard High Speed Steel First make two parallel cuts,...
-
Page 24: General Maintenance
To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance. _1, WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage. A_, WARNING: It is not recommended... -
Page 25: Battery Pack Removal And Preparation For Recycling
(26°C) and free of moisture. • Store Lithium-Ion battery packs in a 30%-50% charged condition. • Every six months of storage, fully charge the Lithium-Ion battery pack. • Exterior may be cleaned with a cloth or soft non-metallic brush. BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING To preserve natural resources, please recycle or dispose of batteries properly. - Page 26 PROBLEM CAUSE SOLUTION The tool does not work Battery is depleted Charge the battery Motor overheating Be sure cooling vents Clean, clear vents. Do are free from dust and not cover with hand obstacles during operation 61199 Manual_Revised_09 0310 Page 26...
- Page 27 12 VOLT LITHIUM-ION CORDLESS MULTI-TOOL MODEL NUMBER 320.61199 The Model Number will be found on the Nameplate attached to the handle of the Multi-Tool. Always mention the Model Number when ordering parts for this tool. ____J 61199 ManuaLRevised_09 0310 Page 27...
- Page 28 61199 Manual_Revised_09 0310 Page 28...
- Page 29 61199 Manual_Revised_09 0310 Page 29...
-
Page 30: Troubleshooting
Your Home For expert troubleshooting and home solutions advice: manage home www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it ! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself For Sears professional installation of home appliances...