Advertisement
_
WARNING:
Read and understand all instruc-
tions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious
personal injury.
SAVE THESE
INSTRUCTIONS
Work Area
•
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
•
Do not operate power tools in explosive atmo-
spheres, such as in the presence
of flammable
liquids, gases, or dust. Power tools may create
sparks which may ignite the dust or fumes.
•
Keep bystanders,
children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
Electrical
Safety
•
Double insulated
tools are equipped with a
polarized
plug (one blade is wider than the
other). This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit,
contact a qualified
electrician
to install a polar-
ized outlet. Do not change the plug in any way.
Double insulation [] eliminates the need for the
three-wire grounded power cord and grounded
power supply system.
•
Avoid body contact with grounded surfaces,
such as pipes, radiators, ranges, and refrigera-
tors. There is an increased risk of electric shock if
your body is grounded.
•
Don't expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
•
Do not abuse the cord. Never use the cord to
carry the tools or pull the plug from an outlet.
Keep cord away from heat, oil, sharp edges, or
moving parts. Replace damaged
cords immedi-
ately. Damaged cords increase the risk of electric
shock.
•
When operating
a power tool outside,
use an
outdoor
extension
cord marked "W-A" or "W".
These cords are rated for outdoor use and reduce
the risk of electric shock.
Personal
Safety
•
Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use tool while tired or under the influ-
ence of drugs, alcohol, or medication. A moment
of inattention while operating power tools may
result in serious personal injury.
•
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in
moving parts.
•
Avoid accidental starting. Be sure switch is off
before plugging in. Carrying tools with your finger
on the switch or plugging in tools that have the
switch on, invites accidents.
•
Remove adjusting
keys or wrenches before
turning
the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in
personal injury.
•
Do not overreach. Keep proper footing and
balance at all times. Proper footing and balance
enables better control of the tool in unexpected
situations.
•
Use safety equipment.
Always wear eye protec-
tion. Dust mask, nonskid safety shoes, hard hat, or
hearing protection must be used for appropriate
conditions.
Tool Use and Care
•
Use clamps or other practical way to secure and
support the workpiece to a stable platform.
Holding the work by hand or against your body is
unstable and may lead to loss of control.
•
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
•
Do not use tool if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
•
Disconnect the plug from power source before
making any adjustments,
changing accessories,
or storing the tool. Such preventive safety mea-
sures reduce the risk of starting the tool acciden-
tally.
•
Store idle tools out of the reach of children and
other untrained persons.
Tools are dangerous in
the hands of untrained users.
•
Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are
easier to control.
•
Check for misalignment or binding of moving
parts, breakage of parts, and any other condi-
tion that may affect the tool's operation. If
damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained
tools.
•
Use only accessories that are recommended
by
the manufacturer for your model. Accessories
that may be suitable for one tool, may become
hazardous when used on another tool.
3
Advertisement
