Specifications; Preventative Maintenance; Additional Safety Information - Craftsman 113.201892 Owner's Manual

e. Neverconnectthe workcableor clamptoany
objectbut the work pieceor metalworktable_
Connecting to otherobjectssuchasbuilding
ground can cause stray currents to flow,
resultingin overheating or fire.
4. PREVENTATIVE MAINTENANCE
'a. Never apply power to the welder with any part
of the "cabinet" removed. Position on-off
switch in "off" position and disconnect welder
from the power supply before doing
maintenance work inside the machine.
Removal of the welder cabinet should be done
only by a qualified service technician.
b. Before connecting the welder power cord to
the receptacle, check the following:
1. Inspect the power cord and welding cables
for cuts or burns and make sure blades and
ground pin on the plug are straighL
2. Inspect "ON-OFF" switch Iever for cracks or
broken parts.
3. inspect electrode holder jaw insulators for
cracks or broken parts.
c. Never weld anything on or to the welder
cabinet, as a burn through may cause
transformer failu re.
d. If any part of your welder is malfunctioning or
has been damaged or broken, such as switch,
cables, helmet, electrode holder, cease
operation immediately and disconnect welder
from the power source and turn switch "OFF"
until the particular part is properly repaired or
replaced.
5. ADDITIONAL SAFETY INFORMATION
a. For additional safety information, purchase
copies of "Practice for Occupational and
Educational Eye and Face Protection" (ANS!
Z87.I), "Safety in Welding and Cutting" (ANSI
Z49_!);_and "Fire Prevention in Use of Cutting
and Welding Processes" (ANSI/NFPA No.
51B) from the American National Standards
Institute, t430 Broadway, New York, New
York, 10018. Purchase copies of "OSHA Safety
and Health Standard" 29 CFR 1910 from the
U.S. Government Printing Office, Washington,
D.C. 20402.
SPECmFgCATIONS
INPUT
Volts AC ................................. 230
Hertz (Cycles) ............................. 60
Rated Input Amps .......................... 50
Delay Action Type Circuit Breaker or Fuse 50Amp
Short Circuit Amps ........................ 67
Power Cord Length ........................ 6'
OUTPUT
AC Low Range Amps .................. 35-140
AC High Range Amps .................. 50-230
DC Range Amps ....................... 30-140
Arc Voltage ................................ 25
AC Open Circuit Volts (max) ............... 74
DC Open Circuit Volts (max) ............... 80
Kilo-Volt-Amps ............................ t2
Kilo-Watts ................................ 7.2
Power Factor % ............................ 60
Duty Cycle % .......................... 20-100
GENERAL
E_ectrode Capacity .................. 1/!6_3/16
Low Hydrogen ....................... !/!6-1/8
Stainless Steel ....................... 1/!6-1/8
Aluminum ........................... 3/32-1/8
Electrode Cable Length .................... 8'
Work Cable Length ........................ 8'
Dimensions ...................... t5 x 12 x 2t
READ AND OBSERVE THE INSTRUCTIONS
APPEARING ON THE WARNING INFORMA-
TION FOUND ON THE CABINET,
ELECTRODE HOLDER AND ON THE INSIDE
OF THE WELDING HELMET,
'I
I ..,_ WARNING E_ECTR,C SHOCK CAN BE fATAl'BEfORE I
TURNING WELDER ON. CHECK THE ELEC]ROOE HOLDER TO
I
BE SURE I'HA_ THERE ARE NO PROTRUDING ,SCREW H_:ADS
ANO THAT ALL INSULATION IS SiECURE
CAUTIg_
U_ 0rdy for!a_
a_d eye p_D_e_b0n
a,_ams_ _dun0u_ _y_ _0m ar_ we_d-
h1_er p!ale Impac_ _e_stantey_ p_9-
tect_o_!hll_
p_a_ ba_k-up p!atR o_
Separate _a!e_y _p_la_es_ should
Impact
Tes_sIant plple$ _ t_0T
u_'_-
br_akPbi_ P_'t$_ 0 rsc_'alched pla_e_
_-r_lechon -- ;_pface_mme_a_I¥
_s_ect _ouen_v and _mmed_a_e_v
LENS @ "_
SHADEN0
MADE f# _TALY
WARNING! ARC WELDING CAN BE iNJURIOUS TO OPERATOI_ AND PERSONS
IN THE WORK AREA _ CONSULT OWNERS MANUAL BEFORE OPERATING
To get the most from your welder we suggest you read the manual carefully --
even if you're an accomplished welder, and keep it available to serve as a
handy reference, or in the event that repair parts would be required.
FULL ONE YEAR WARRANTY
ON
CRAFTSMAN ELECTRIC WELDER
If this Craftsman Electric Welder fails to perform properly, due to a delecI in material or workmanship, within one year
from the date of purchase, Sears will repair it free o{ charge. this warranly applies only while this product is in use in the
United States
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RE[URNING THE WELDER TO THE NEAREST SEARS STORE OR
SERVICE CENTER THROUGHOUT THE UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
SEARS. ROEBUCK AND CO,. Dept. 698/731A. Sears Tower. IL 60684
3