Table of Contents
Advertisement
OWNER'S
MANUAL
MODEL NO.
315.174710
CAUTION:
Read Rules for
Safe Operation
and All Instruc-
tions Carefully
II III
"111 IIIIII
in,,i
...............
®
Router
Double Insulated
Illl I llllll
I Illllllll
I lll
I I 'lllllI
Thank You for Buying
Craftsman
Tools
_l
in
,i.
Warranty
Introduction
Operation
Maintenance
,, Repair Parts
Designed exclusively for and sold only by
SEARS, ROEBUCK AND CO, Sears Tower, Chicago, IL 60684
612547-8! 5
4-92
®
PR}NTED IN U S A
Advertisement
Table of Contents
Related Manuals for Craftsman 315.174710
Summary of Contents for Craftsman 315.174710
- Page 1 I I 'lllllI Warranty Introduction Operation ® Thank You for Buying Maintenance Craftsman Tools ,, Repair Parts Designed exclusively for and sold only by SEARS, ROEBUCK AND CO, Sears Tower, Chicago, IL 60684 612547-8! 5 PR}NTED IN U S A...
-
Page 2: Rules For Safe Operation
iU,,ll ....FULL ONE YEAR WARRANTYON CRAFTSMANROUTER If thisCraftsmanRouter tailsto givecomplete satisfaction w ithin oneyearfromthedate of purchase RETURNrr TO THENEARESTSEARSSERVICECENTER/DEPARTMENTTHROUGHOUTTHE UNITEDSTATESandSearewilt repairit, free of charge. Ifthlsrouter isused for commercial or rentalpurposes t hiswarranty appliesforonly90days from thedateofpumhass,, Thiswarrantygives you specific legalrights,and youmay alsohaveotherrights which vary fromstate tostate. SEARS,ROEBUCKAND CO, DEPT.73tCR-W SEARSTOWER... - Page 3 Do not operate tool while under the influence of drugs, alcohol, or any medication. 3& When servicing use only Identical Craftsman replacement parts. SAVE THESE INSTRUCTIONS. Review them frequently and use them to instruct others who may use this toot. If you loan someone this tool, loan them these instructions also.
-
Page 4: Product View
OPERATION Your router is a versatile woodworking toot which will give you years of trouble-free performance It is engineered with the professional in mind, but its ease of operation allows the amateur to produce work which ts beauttft,,_l and precise. KNOW YOUR ROUTER... -
Page 5: Electrical Connection
OPERATION INSTALL1NG/REMOVING CUTTERS CUTTER TURN TO ACTIVATE See Figure2, SPINDLE LOCK t+ UNPLUGYOUR ROUTER+ A Spindle lock is located on the front of the motor housing See Figure 1, To activate lock, push spindle lock tn and slide into lock position, Place your muter upside down on tab{e, then turn collet nut with wrench until lock mechanism... -
Page 6: Depth Stop Rings
OPERATION DEPTH OF CUT ADJUSTMENTS (Continued) UNPLUG YOUR ROUTER. Place your muter on a flat surface, unlock clamping tever, and adjust until cutter is inside subbaso. Figure 3 Turn the depth adjusting ring until tip of cutter touches flat surface, See Figure 4, Position your router so that the cutter can extend below the subbase for desired depth setting, Turn the depth adjusting ring to obtain the desired depth... -
Page 7: Routing
When it is advanced into the work too slowly, a Sea Figure 8. revolving bit does not dig into new wood fast enough to take Your Craftsman Router is an extremely high-speed tool a bite; instead, itsimplyscrapesaway sawdust-_ike padicles. (25,000 RPM no-load speed), and will make clean, smooth... - Page 8 OPERATION TOO SLOW FEEDING (Continued) "Too.stow feeding" can also cause your routerto take off in a wrong direction from the intended line of cut, Always grasp DEPTH and hold your router firmly with both hands when rout e Ing. OF_UT 14--- WIDTH OF CUT You can detect "too-slow feeding"...
-
Page 9: Edging With Pilot Bits
OPERATION STARTING AND ENDING A CUT INTERNAL ROUTING Tilt router and place on workpiece, letting edge of subbase contact workpiece first Be careful not to let router bit contact workpieceo Turn router on and let motor buffd to its full speed. Gradually feed cutter into workpiece until subbase is level with workpiece. -
Page 10: Depth Adjusting Ring Adjustments Or Replacement
MAINTENANCE SWITCH REPLACEMENT See Figures 13 & 14 1, UNPLUG YOUR ROUTER. 2, Remove screws (A) and handle cover (B). See Figure 3, NOTE THE LOCATION OF THE MOLDED BEND RE- LIEF (C) ON THE POWER HANDLE CORD, ALSO NOTE ALL WIRING IN THE HANDLE AND HOW EACH LEAD IS CONNECTED TO THE SWITCH°... - Page 11 MAINTENANCE DEPTH ADJUSTING RING =ill ADJUSTMENTS OR REPLACEMENT (Continued) REAR OF DEPTH ADJUSTING RING To replace depth adjusting ring; Remove depth stop rings, To remove: Depress lip on depth stop ring and sfide end of depth stop ring over Itp_ See Figure 15.
- Page 12 MAINTENANCE GENERAL Only the parts shown on parts list, page 15, are intended When electric tools are used on fiberglass boats, sports cars, wallboard, spackling compounds, or plaster, it has be repaired or replaced by the customer All other parts been found that they are subject to accelerated wear and...
- Page 13 ACCESSORIES ----- THE FOLLOWING RECOMMENDED ACCESSORIES ARE CURRENT AND WERE AVAILABLE AT THE TIME THIS MANUAL WAS PRINTED. (9-2579) Template Guide Bushings (9°25082) Dovetail Template (9-2580) Rout-A-Form Pantograph (9-25183) Box Joint Temptate (9-25254) Template (9-2573) MiU Works Molding Maker BIs-Kit Plate Jointer Kit (9-25423) Sharpening (9-66501)
-
Page 14: Parts List & View
CRAFTSMAN ROUTER - MODEL NUMBER 315,174710 ..SEE NOTE "A" NOTE: _A" - The assembly shown represents an important part of the Double Insulated System. To avoid the possibility of alteration or damage to the System, service should be performed by your nearest Sears Repair Center°... -
Page 15: Parts List
' " CRAFTSMAN ROUTER - MODEL NUMBER 315,174710 ..,, , ,,i, ,,,,, , ,,,, ,,, ,,,,,,, , ,t i,,,i,,,,,,, i The model number will be found on a plateattached to the motor houslng. Always mention the model number in all correspondence regarding your ROUTER or when ordering repair parts,... -
Page 16: How To Order Repair Parts
CRRFTgMRN ° OWNER'S Router MANUAL Double Insulated Now that you have purchased your Router, should a SERVICE need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co, stores. Be sure to provide all pertinent facts when you call or visit°...