GE 22 Owners And Installation Manual page 43

Performance Data Sheet
SmartWater Filtration System-GE ® MSWF Cartridge
This system has been tested and certified in filter model GE MSWFaccording to NSF/ANSI S tandards 42 and 53 for reduction of the substances listed below.
The concentration of the indicated substances in water entering the system was reduced to a concentration lessthan or equal to the permissible limit for water
leaving the system, as specified in NSF/ANSI S tandards 42 and 53.* (Safety factors built in for unmetered usage.)
Standard No. 42: Aesthetic effects
lnflue,t Challenge
Parameter ' USEPAMCL I Concentration
2.0 mg/L ± 10%
at least 10,000 particles/
mL
Standard No. 53: Health effects
influent Challenge
Parameter
Effluent % Reduction
Average Maximum Average ' Maximum Min, Required Reduction
0.06 mg/L 0.10 mg/L 97% 9.1% ->50%
408,333 670.000 95.5% 89.4% ->85%
Effluent ' % Reduction ' Hax. Permissible
USEPAMCL Concentration Average Maximum Average Maximum
1 NTU.... 11 ± 1 NTU .... 0.38 NTU 0.5 NTU 96.5% 95.4%
99.95% Reduction Minimum 50.000 L < 1 #/L 4 #/L > 99.99% > 99.99%
0.010 mg/L 0.15 mg/L ± 10% < 1 ppb < 1 ppb 99.3% 99.3%
0.010 mg/L 0.15 mg/L ± 10% 3.1 ppb 9.0
ppb
98.0% 9s.s%
0.002 mg/L 0.006 mg/L ± 10% 0.34 ppb 0.7 ppb 94.0% 89.6%
0.002 mg/L 0.006 mg/L ± 10% 0.66 ppb 1.5 ppb 88.4% 73.7%
0.0002 mg/L 0.002 mg/L ± 10% < 0.02 ppb < 0.02 ppb > 99.0% > 99.0%
0.003 mg/L 0.009 mg/L ± 10% < 0.5 ppb < 0.0S ppb > 93.9% > 94.3%
0.070 mg/L 0.210 mg/L ± 10% 7.7 ppb S5 ppb 96.0% 82.0%
0.003 mg/L 0.015 mg/L ± 10% < 1 ppb < 1 ppb >92.9% > 92.9%
0.005 mg/L 0.015 mg/L ± 10% < 0.5 ppb < 0.5 ppb >96.8% > 97.0%
0.040 mg/L 0.080 mg/L ± 10% < 1 ppb 1 ppb > 98.7% > 98.7%
0.075 mg/L 0.225 mg/L ± 10% < 0.S ppb < 0.5 ppb > 99.7% > 99.8%
99% Reduction 107 tel0 8fibers/L; <0.17 NF/L <0.17 NF/L >99% >99%
ifibers > 10pm in length
"Testedusing pressure of 60 psig;pH of 7.5+ 0.5;temp of 68o+ S°F(20° + 2.5°C).
"'Measurement in Partides/mL Particles used were 0.5 1 microns.
""Based on the useof Cryptosporidium parvum oocysts.
.... NTU Nephelometric Turbidity Units
Product Water
0.5 NTU
99.95%
0.010 mg/L
0.010 mg/L
0.002 mg/L
0.002 mg/L
0.0002 mg/L
0.003 mg/L
0.070 mg/L
0.003 mg/L
0.005 mg/L
0.040 mg/L
0.075 mg/L
99% Reduction
Capacity 300gallons (1.135liters). Contaminant reduction determined by NSFtesting.
Application Guidelines/Water Supply Parameters
ServiceFlow
WaterSupply
It isessentialthat the manufacturer'srecommended installation,maintenanceandfilter replacement r equirementsbe carriedout for the productto perform asadvertised.
Seeinsert for Warrantyinformation.
Operating Specifications
• Pressurerequirement: 40 120 psi (2.8 8.2 bar),non shock
• Temperature: 33 100°F(0.6-38°C)
• Flow rate: 0.9 gpm (3.14Ipm)
General Installation/Operation/Maintenance Requirements
• Flushnew cartridge at full flow for 4 1/2 gallons(aboutfive minutes)to purge
trapped air.
• Replacecartridge when flow becomes too slow.
, Protect from freezing by removing filter cartridge when temperatures are
expected to drop below 40°F (4.4°C).Do not install systems in areas where
ambient temperatures may go above IO0°F or below 40°E Do not install
on a hot watersupply.
Special Notices
Installation instructions are included with the product when shipped.
This drinking water system must be maintained according to manufacturer's
instructions, including replacement of filter cartridges.
• Do not use with water that is microbiologically unsafe or of unknown quality with
out adequate disinfection before or after the system. Systemscertified for cyst
reduction may be used on disinfected water that may contain filterable cysts,
• The contaminants or other substances removed or reduced by this water
treatment system are not necessarily in your water.
Check for compliance with the applicable state and local laws and regulations.
Note that while the testing was performed under standard laboratory conditions.
actual performance may vary. Systems must be installed and operated in
accordance with manufacturer's recommended procedures and guidelines.
Installation and use MUST comply with all state and local plumbing codes. Do not
install if water pressure exceeds 120 psi. If your water pressure exceeds 80 psi
(552 kPa).you should install a pressure limiting valve. Contact a plumbing
professional if you are uncertain how to check your water pressure.
Do not install where water hammer conditions may occur. If water hammer
conditions exist you must install a water hammer arrester. Contact a plumbing
professional if you are uncertain how to check for this condition.
Where a backflow prevention device is installed on a water system, a device for
controlling pressure due to thermal expansion must be installed.
Forconditions of use, health claims certified by the California Department of Public
Health, and replacements, see performance data sheet. California Department
of Public Health Certification #06 1834.The contaminants or other substances
removed or reduced by this water filter are not necessarily in all users'water,
Tested and Certified by NSF International against ANSI/NSF Standards 42 and 53 in model GE P1SWF for the reduction of:
Standard No. 42: Aesthetic Effects
, Chemical
Chlorine Taste and Odor
. Mechanical Filtration
Particulate Reduction. Class]
GE
Appliances
Appliance Park
Louisville, KY40225
geapplianceparts.com
Standard No. 53: Health Effects
, Chemical Reduction
Atrazine Reduction
Endrin Reduction
Benzene and Carbofuran Reduction
1,4 DicNorobenzene and
2,4-D Reduction
Lead and Lindane Reduction
Mercury and Toxaphene Reduction
, Mechanical Filtration
Cyst and Asbestos Reduction(_
REPLACEMENT ELEMENT
EPA#20350-MN-005
© 2020 General Electric Company PC61577C
43