Unpacking 1 Universal Monitor Mount Models 1 UMM-LW-20B Fixed Wall Mount 2 2.1.1 Parts List 4 2.1.2 Installing the UMM-LW-20B Fixed Wall Mount 5 UMM-LW-30B Tilt/Swivel Wall Mount 9 2.2.1 Parts List 11 2.2.2 Installing the UMM-LW-30B Tilt/Swivel Wall Mount 12...
This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper. Verify that all parts shown in the Parts List are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative.
| Universal Monitor Mount Models Universal Monitor Mounts 2.1 UMM-LW-20B Fixed Wall Mount The UMM-LW-20B is a fixed wall mount that is designed for use with any Bosch LCD flat-screen monitor. The mount moves the monitor 1.5 cm (0.59 in.) off of the wall.
Page 5
Mounting Surface: 3600 psi or 25 Mpa Hollow cinder block Minimum 2-in. x 4-in. wood stud with maximum 0.5- in. thick wallboard 3/4-in. construction grade plywood Table 2.1 UMM-LW-20B Specifications Bosch Security Systems, Inc. Mounting Guide F.01U.115.026 | 3.0 | 2008.12...
1/4 x 2.0 in. Wedge anchors (C) (see Figure 3.3 on page 18 for a dimensional drawing) 1/2 x 2.0 in. Wood screws (D) (see Figure 3.3 on page 18 for a dimensional drawing) F.01U.115.026 | 3.0 | 2008.12 Mounting Guide Bosch Security Systems, Inc.
M4 x 10 mm screws (E) (see Figure 3.4 on page 19 for a dimensional drawing) Level (F) 2.1.2 Installing the UMM-LW-20B Fixed Wall Mount To install the wall mount: Disassemble the mounting plate (A) from the wall bracket by removing the lock screw from the wall bracket (B).
Page 8
Use the two (2) wedge anchors (C) to attach the wall bracket to concrete or to a cinder block. Use the two (2) wood screws (D) to attach the wall bracket to a stud behind wallboard or to construction-grade plywood. F.01U.115.026 | 3.0 | 2008.12 Mounting Guide Bosch Security Systems, Inc.
Page 9
(4) M4 x 10 mm screws (E). Figure 2.3 Attach the VESA monitor plate Carefully slide the mounting plate into the slots of the wall bracket. Figure 2.4 Attach monitor plate to wall bracket Bosch Security Systems, Inc. Mounting Guide F.01U.115.026 | 3.0 | 2008.12...
Page 10
Universal Monitor Mounts Tighten the lock screw, located on the right side of the wall bracket, using a Phillips head screw driver. Figure 2.5 Lock screw on the wall bracket F.01U.115.026 | 3.0 | 2008.12 Mounting Guide Bosch Security Systems, Inc.
The UMM-LW-30B is a tilt/swivel wall mount that is designed for use with any Bosch LCD flat-screen monitor. This mount allows you to swivel the mount 360 degrees to position the monitor in either landscape or portrait view. The mount also allows you to pan and tilt the monitor 140 (±70) degrees for the best viewing...
Page 12
Solid concrete with a recommended strength of 3600 psi or 25 Mpa Table 2.2 UMM-LW-30B Specifications WARNING! Do not install the UMM-LW-30B wall bracket into mortar joints or non-filled cinder block walls. F.01U.115.026 | 3.0 | 2008.12 Mounting Guide Bosch Security Systems, Inc.
1/4 x 2.0 in. Wedge anchors (C) (see Figure 3.3 on page 18 for a dimensional drawing) 1/2 x 2.0 in. Wood screws (D) (see Figure 3.3 on page 18 for a dimensional drawing) Bosch Security Systems, Inc. Mounting Guide F.01U.115.026 | 3.0 | 2008.12...
Retain the thumb screw for later use. Determine the location on the wall that you will attach the wall bracket (B). Use Table 2.2, on page 10, for recommended mounting surfaces. F.01U.115.026 | 3.0 | 2008.12 Mounting Guide Bosch Security Systems, Inc.
Page 15
Use the two (2) wood screws (D) to attach the wall bracket to a stud behind wallboard or behind construction-grade plywood. Align the back of the monitor to the correct hole pattern on the VESA mounting plate. Bosch Security Systems, Inc. Mounting Guide F.01U.115.026 | 3.0 | 2008.12...
Page 16
(4) M4 x 10 mm screws (E). Figure 2.8 Attach the VESA mounting plate Carefully slide the mounting plate into the slots of the wall bracket. Figure 2.9 Attach monitor plate to wall bracket F.01U.115.026 | 3.0 | 2008.12 Mounting Guide Bosch Security Systems, Inc.
Page 17
Tilt and swivel the mount to achieve the optimum viewing angle. Use the wrench (G) to tighten the nut, located on the left side of the mount. Figure 2.11 Tighten nut to lock mount position Bosch Security Systems, Inc. Mounting Guide F.01U.115.026 | 3.0 | 2008.12...
| Dimensional Drawings Universal Monitor Mounts 3.3 UMM Series Component Dimensions ø6 mm ø12.5 mm ø5 mm ø6.3 mm 9.8 mm Figure 3.3 Wedge Anchor and Wood Screw Dimensions F.01U.115.026 | 3.0 | 2008.12 Mounting Guide Bosch Security Systems, Inc.
Page 21
Universal Monitor Mounts Dimensional Drawings | en 19 ø7.5±0.15 mm ø3.95±0.05 mm ø3.8±0.05 mm Figure 3.4 M4x10 mm Screw Dimensions Bosch Security Systems, Inc. Mounting Guide F.01U.115.026 | 3.0 | 2008.12...