1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Storage
  5. XM-7002B
  6. Specification

Toshiba XM-7002B Specification

Cd-rom drive
Hide thumbs
Table of Contents

Advertisement

Quick Links

TOSHIBA
DISK PRODUCTS DIVISION
XM-7002B
CD-ROM DRIVE

PRODUCT SPECIFICATION

JUNE 1999
Rev. 1.0
Specifications are subject to change without notice
DOCUMENT NUMBER
12095

Advertisement

Table of Contents
loading

Related Manuals for Toshiba XM-7002B

Summary of Contents for Toshiba XM-7002B

  • Page 1: Product Specification

    TOSHIBA DISK PRODUCTS DIVISION XM-7002B CD-ROM DRIVE PRODUCT SPECIFICATION JUNE 1999 Rev. 1.0 Specifications are subject to change without notice DOCUMENT NUMBER 12095...
  • Page 2 1.This product has no over-current protection circuit. System should have appropriate over-current protection. Toshiba Corporation makes no warranty of damages caused by no over-current protection. 2.This has a little possibility of errors. To prevent damages and injury caused by the above, careful consideration for the safety and integrity should be taken in the system design.

  • Page 3: Table Of Contents

    6.2.2.Timing of Host Interface(PIO) ---------------------------------------------------------------------------------------- 15 6.2.3.Timing of Host Interface(DMA Multi) ------------------------------------------------------------------------------ 16 6.2.4.Timing of Host Interface(Ultra DMA) ------------------------------------------------------------------------------ 17 6.3. Connector ----------------------------------------------------------------------------------------------------------------------- 18 6.4.Suppor Commmand List -------------------------------------------------------------------------------------------------- 6.4.1.ATAPI Packet Command for CD-ROM Device ---------------------------------------------------------------- 19 6.4.2.ATA Commandfor ATAPI CD-ROM Device --------------------------------------------------------------------- 20 XM-7002B Rev.1.0...
  • Page 4 11.1. Disc ------------------------------------------------------------------------------------------------------------------------------- 24 11.2. Optical Pickup ---------------------------------------------------------------------------------------------------------------- 24 12. Emergency Eject ------------------------------------------------------------------------------------------------------------------- 24 13. Safety Standards/Agency Approvals --------------------------------------------------------------------------------------- 24 14. Electrostatic Discharge ---------------------------------------------------------------------------------------------------------- 25 15. Accessories ------------------------------------------------------------------------------------------------------------------------- 25 16. Packaging ---------------------------------------------------------------------------------------------------------------------------- 25 17. CE Declaration of conformity ------------------------------------------------------------------------------------------------- 25 XM-7002B Rev.1.0...

  • Page 5: Introduction

    1. Introduction This document describes Toshiba's XM-7002B CD-ROM Drive. This drive reads digital data stored on CD-ROM and CD-Audio discs. The CD-ROM disc is single sided and has a 12 cm or 8 cm diameter. It typically contains approximately 600 MBytes or 200 MBytes of information respectively. (1 MByte=2 Bytes) This drive reads digital data stored on CD-ROM discs at maximum 24 times faster rotational speed.

  • Page 6: Features

    (23) Software Volume Control via ATAPI Mode Select Command (24) MTBF 60,000 POH (25) DataTransfer Rate PIO Mode 4 (Data Transfer Rate16.7 MB/s) DMA: DMA Multi Word Transfer Rate Mode 2 : Ultra DMA Transfer Rate Mode 2 (26) Support Vibration Detect Function 2/27 XM-7002B Rev.1.0...

  • Page 7: Specifications

    Approx. 660-1,500 KByte/s (4.4-10X) Approx. 1,545-3,600 KByte/s (10.3-24X) (Yellow-Book Mode 2) Approx. 752-1,710 KByte/s (4.4-10X) Approx. 1,716-4,104 KByte/s (10.3-24X) Burst(ATAPI Interface) 16.7 MBytes/s (PIO Mode 4) 16.7 MByte/s (DMA multi word Mode2) 33.3 MByte/s (ULTRA DMA Mode2) 3/27 XM-7002B Rev.1.0...
  • Page 8 2. Software Release (ATAPI command) 3. Emergency Eject (9) Air Flow Not Required (10) Acoustic Noise Less than 40 dB (with A weighted/Average) at 1 meter of Front Bezel Operation mode:Full stroke Access (11) Power Supply +5 V(details in Section 7) 4/27 XM-7002B Rev.1.0...

  • Page 12: Vibration Detection

    (2) This drive was tuned up to detect the vibration on the assumption that the drive was mounted in Toshiba DynaBook Satellite Pro 440 series. Mounting condition in Toshiba DynaBook Satellite Pro 440 series is shown in Figure 3. There will be possibility that the drive does not detect the vibration. It depends on mounting condition.
  • Page 13 (Unit:mm) Figure 4 External Dimensions 9/27 XM-7002B Rev.1.0...

  • Page 14: Reliability

    (6) IDE/ATAPI Interface Control Circuit (7) System Control Circuit (8) Analog Audio output 4.2. Optical Pickup Semiconductor Laser and 3-beam System 4.3. Spindle Motor Brush- less DC Motor 4.4. Feed Motor DC Motor with Non-contact Type Velocity sensor 10/27 XM-7002B Rev.1.0...
  • Page 15 Figure 5 Basic configuration of XM-7002B 11/27 XM-7002B Rev.1.0...

  • Page 16: Functions

    Initialization Focus Serch Max 3.5 s Spindle ON Typ.13 s, Max 16 s Learning (Single Session Disc) Idle "TEST UNIT READY" Any Command Sendable "Read-Command"Acceptable Command "Good"Status Correspondence "Check Condition"Status Can't send COMMAND Figure 7 Initialization Sequence 12/27 XM-7002B Rev.1.0...

  • Page 17: Standby Mode

    Power Supply cablesPIN No.38 - 42(+B),43 - 45(GND) 1.5 A Table 1 Cable parameters 6.2.Signal summary The physical interface consists of single ended TTL compatible receivers and drivers communicating through a 50P-conductor as shown in Figure 9,10 - 13. 13/27 XM-7002B Rev.1.0...

  • Page 18: Signal Specifications

    Rs=470 OHM, CSEL CSEL /DMACK Input HIGH Voltage 2.0 V Rx=100 kOHM Input LOW Voltage 0.8 V Rs=1 kOHM Input leakage Current -5 µA Pullup Resistor(Ri) -150 µA /RESET Input Capacitance 8 pF Figure 9 Signal Specifications 14/27 XM-7002B Rev.1.0...

  • Page 19: Timing Of Host Interface(Pio)

    DIOR- data hold DIOR- data tristate Addr valid to IOCS16- assertion Addr valid to IOCS16- negation DIOR-/DIOW- to address valid hold Read Data Valid to IORDY active IORDY setup time IORDY pulse wide 1250 Figure 10 Host Interface Timin 15/27 XM-7002B Rev.1.0...

  • Page 20: Timing Of Host Interface(Dma Multi)

    DIOR/DIOW- data setup DIOW- data hold DMACK to DIOR-/DIOW- setup DIOR-/DIOW- to DMACK hold DIOR- negated pulse width DIOW- negated pulse width DIOR- to DMREQ delay DIOR- to DMREQ delay Figure 11 Host Interface Timing (DMA Multi) 16/27 XM-7002B Rev.1.0...

  • Page 21: Timing Of Host Interface(Ultra Dma)

    Envelope time tENV Minimum Delay time for Driver t2AD Minimum time for DMACK- t2IORODY First STROBE time Ready-to-Final STROBE time tRFS Ready-to-Pause time Limited Iuterlock time Interlock with minimum tMLI Figure 12 Host Interface Timing (Ultra DMA) 17/27 XM-7002B Rev.1.0...

  • Page 22: Connector

    Vender unique * N.C (OPEN) A slash character(/) at the beginning of a signal name indicates it is asserted at the low level (active low). * Do not connect anything with vender unique (50P). Figure 14 Signal assignments 18/27 XM-7002B Rev.1.0...

  • Page 23: Suppor Commmand List

    READ FORMATTED CAPACITIES COMMAND READ HEADER READ SUB-CHANNEL READ TOC READ TRACK/RZONE INFORMATION COMMAND REQUEST SENSE REZERO UNIT SEEK SET CD-ROM SPEED SET READ AHEAD COMMAND SET STREAMING COMMAND SEND EVENT COMMAND STOP PLAY/SCAN START/STOP UNIT TEST UNIT READY 19/27 XM-7002B Rev.1.0...

  • Page 24: Ata Commandfor Atapi Cd-Rom Device

    6.4.2. ATA Command for ATAPI CD-ROM Devices Command OP Code XM-7002B ATAPI SOFT RESET CHECK POWER MODE EXECUTE DRIVE DIAGNOSTICS IDLE IMMEDIATE IDLE ATAPI PACKET COMMAND ATAPI IDENTIFY DEVICE SET FEATURES SLEEP STANDBY IMMEDIATE STANDBY 20/27 XM-7002B Rev.1.0...

  • Page 25: Power Requirements

    0.03 % Max. (at 1 kHz weighted 20 kHz LPF) (7) Signal to Noise Ratio 78 dB Typ (IEC 179 A-weighted) 8.1.1. Audio Cable Unbalanced and shielded (1) Capacitance Less than 1000 pF (2) Length Max. 3 m 21/27 XM-7002B Rev.1.0...
  • Page 26 9.1 Master mode setting Open the PIN 47 of I/O conectors. 9.2 Slave mode setting Short-circuit the PIN 47 and PIN 48 of I/O connectors. *Master mode can be oppositely to Slave mode according to the specification. (CSEL mode) 22/27 XM-7002B Rev.1.0...
  • Page 27 (3) When performing 'Data Access' and during 'Data Transfer' Busy Indicator keeps turn On. Light On Figurer 19 Data Access and Data Transfer (4) When pushing Eject button, Busy indicator is blinking at 0.4 s intervals. 0.4 s Light Off at the Eject Figurer 20 Eject 23/27 XM-7002B Rev.1.0...
  • Page 28 IEC61000-4-4 : 1995 [AC-line: 1 kV, f: 5 kHz, Polarity:+/- ] IEC61000-4-5 : 1995 [AC-line: 1 kV/2 kV, Polarity:+/- ] IEC61000-4-6 : 1996 [3 V, 0.15-80 MHz, 1 kHz 80 % AM] IEC61000-4-8 : 1993 [1 A/m, 50 Hz] (5) EMI KOREAN EMI Regulation (RRL) 24/27 XM-7002B Rev.1.0...
  • Page 29 *Transportaion must be executed with each palette. b. 20 units in a Bulk Pack 24 Bulk Packs on one Pallet Packing Specifications :for 25 Packaged Model: IB-CD2-A90012 :for 20 Packaged Model: IB-CD2-A90013 17. CE Declaration of conformity Please refer to attached Annex 1. 25/27 XM-7002B Rev.1.0...
  • Page 30 Options: None Toshiba declares that the above mentioned product(s) with or without the listed options comply to the EU-Directives and standards as listed on page 2. Last two digits of the year in which the CE mark affixed : 98...
  • Page 31 27/27 XM-7002B Rev.1.0...

Table of Contents