Advanced Menu Operations - Sony DXC-D35 Service Manual

Viewfinder Advanced Menu
Bring up the advanced menu pages by setting the
POWER switch to ON while pressing the UP/ON
button up (see page 52).
There are up to 15 advanced menu pages (the number
displayed depends on the switch settings and the type
of connected VTR).
Note on EZ mode
When the camera is in EZ mode, the advanced menu
does not appear. Release the EZ mode beforehand.
(See page 14.)

Advanced Menu Operations

To change the page
Move the cursor to the menu number, then press the
UP/ON button or the DOWN/OFF button.
Pressing the UP/ON button displays the previous page
and pressing the DOWN/OFF button displays the next
page. Pressing the DOWN/OFF button when the last
page is being displayed returns the display to the first
page.
To select items in a page
Press the MENU/STATUS switch to move the cursor
among the menu items.
To change settings
This operation is the same as for the basic menus.
For a description of basic menu operations, see page 58.
To return to the normal indications
Move the cursor to EXIT MENU, then press the UP/
ON button.
Contents and Settings of Each
Page
Each page's contents and settings are described below.
64
Chapter 4 Viewfinder Screen Indications and Menus
Advanced menu page 1
Use this page to return all advanced menu settings to
their factory preset values.
For details of this operation, see "Displaying the advanced
menu and switching to the normal indications" (page 52).
Advanced menu page 2
Item Settings
GAIN
This sets gain values for the positions of the GAIN switch.
The HIGH, MID, and LOW values must be set so that LOW
< MID < HIGH.
LOW –3 dB, 0 dB (normal
Sets the L position. value), 3 dB, 6 dB, 9 dB, 12
dB, 18 dB, 18 dB + DPR, 24
dB
MID 0 dB, 3 dB, 6 dB, 9 dB
Sets the M position. (normal value), 12 dB, 18
dB, 18 dB + DPR, 24 dB, 24
dB + DPR
HIGH 3 dB, 6 dB, 9 dB, 12 dB, 18
Sets the H position. dB (normal value), 18 dB +
DPR, 24 dB, 24 dB + DPR,
HYPER GAIN
HYPER 36 dB (normal value), 42
Sets gain value when the dB
HYPER GAIN is selected.
DL ON (normal value), OFF
Sets DynaLatitude function When set to ON, the amount
ON/OFF. of DynaLatitude effects is
This setting is valid only set in basic menu page 3
when the OUTPUT/DL/ (see page 59).
DCC+ switch has been set to
DL.
Advanced menu page 3
a)
a) For DXC-D35P/D35WSPL: EBU75
Item Settings
AWB MEM 2 (normal value): No
Selects whether or not to correspondence with FILTER
make the FILTER knob knob settings. Only two
settings (1 to 4) correspond adjustment values (A and B)
to separate white balance are stored in memory.
adjustment values stored in 2 4FL: Correspondence
memory. with FILTER knob settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
TONE ON (normal value): Output
Selects whether or not to audio signal.
output a 1-kHz audio signal OFF: Do not output audio
with the color bars when the signal.
OUTPUT/DL/DCC+ has
been set to BARS.
BARS SMPTE (normal value for
Selects normal width or DXC-D35/D35WSL):
narrower width for color Normal width
bars. EBU75 (normal value for
DXC-D35P/D35WSPL): EBU
75%
EBU100 (for DXC-D35P/
D35WSPL): EBU 100%
SPLIT (for DXC-D35P/
D35WSPL): Not for normal
operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
REMOTE1 REC (normal value):
Sets a function for position 1 Specifies recording start/stop
of a switch connected to the MARK: Specifies a Mark IN/
REMOTE1 connector. OUT point.
CUE: Specifies a cue point.
NG: Specifies NG/OK.
REMOTE2 REC: Specifies recording
Sets a function for position 2 start/stop.
of a switch connected to the MARK (normal value):
REMOTE1 connector. Specifies a Mark IN/OUT
point.
CUE: Specifies a cue point
NG: Specifies NG/OK.
BAUD RATE 9600, 38400 (normal value)
Sets a baud rate for a
computer connected to the
REMOTE connector 2 (to be
supported in future version).
Advanced menu page 4
cPAGE4 (NEXT cV PREVcv)
MARKER : CENT/90%
LIMITS : OFF
ZEBRA : 1
a)
ZEBRA1 : 70IRE
VF S DTL: 0
VF TALLY: 2
VF PLAY : Y
LENS SEL: 1
EXIT MENU (YEScv)
a) For DXC-D35P/D35WSPL: 70%
Item Settings
MARKER CENT/90% (normal value):
Selects ON/OFF setting for Displays center marker and
center marker, size setting safety zone marker at 90%
(percentage of viewfinder size.
screen area), and display CENT/80%: Displays center
ON/OFF setting. marker and safety zone
marker at 80% size.
90%: Displays only safety
zone marker at 90% size.
80%: Displays only safety
zone marker at 80% size.
CENT: Displays only center
marker.
LIMITS (For DXC-D35WSL/ OFF (normal
value):FDepends on the
D35WSPL)
Selects the safety zone size scan size.
when the scan size is 16:9.
4:3, 13:9, 14:9, 15:9
ZEBRA 1 (normal value): Displays
Selects type of zebra pattern the zebra pattern over parts
display. having a video level.
between 70 and 90 IRE (or
70 and 90%).
Use the next item (ZEBRA1)
to select the base level.
2: Displays the zebra pattern
over parts having video
levels of 100 IRE or above
( or 100% or above).
1/2: Dual display (both 1
and 2)
ZEBRA1 70 IRE (normal value) to 90
Sets base level for zebra IRE or 70% (normal value)
pattern 1. to 90%
Can be set for each IRE
step or 1% step.
VF S DTL –99 to ±0 (normal value) to
Sets the detail level of +99
images on the viewfinder Negative values set softer
screen (displayed only when edges and positive values
a viewfinder other than the set sharper edges.
DXF-701/701CE/701WS/
701WSCE/801/801CE is
attached).
(continued)
65
Chapter 4 Viewfinder Screen Indications and Menus