Philips HP4648/39 ProCeramic User Manual

1 Insert the plug into the wall socket.
2 Press the on/off button.
The ready-for-use light turns red to indicate that the straightener is heating
up. HP4648/27 only: ions are generated automatically as soon as the
straightener is switched on and are released through the ion output holes.
3 Let the appliance heat up.The default temperature setting is 140
(HP4648/17, HP4648/27 and HP4648/37) or 180 (HP4647/07).
Never leave the appliance unattended when it is plugged in. Never put
the appliance on a surface that is not heat-resistant when it is heating up
and when it is hot.
Tip: by closing the plates with the closing lock (not available on
B
HP4647/07), the straightener heats up more quickly.
4 When the ready-for-use light turns red the default temperature
setting has been reached.When the appliance has reached this
temperature setting, you can adjust the setting to your preference
(fig. 2).
- Press the + button to increase the temperature setting or press the -
button to decrease the temperature setting.The display tells you which
setting you have selected.The ready-for-use light turns red to indicate
that the appliance is adjusting the setting.
- The ready-for-use light turns green when the selected setting has been
reached.
5 Comb or brush your hair so that it is disentangled and smooth
(fig. 3).
Use a comb to divide the hair into sections. Do not put too much hair in
one section.
Tip: it is better to section off the crown area and to straighten the hair
B
underneath first, followed by the top area.
6 Take a section that is not wider than 5 cm. Place it between the
straightening plates and press the handles of the appliance firmly
together.
7 Slide the straightener down the length of the hair in 5 seconds, from
root to hair end, without stopping to prevent overheating (fig. 4).
8 Repeat this process after 20 seconds until you have achieved the
desired look.
9 Allow your hair to cool down. Do not comb or brush it before it has
cooled down, as this would ruin the hairstyle you have just created.
Reducing frizz and static electricity (HP4648/27 only)
The ioniser inside the hairstyler generates streams of ions that surround and
condition your hair. Ions reduce frizz and static electricity and leave your hair
looking soft, smooth and shiny.
The ioniser starts working as soon as the appliance is switched on.
Cleaning
.
1 Make sure the appliance is switched off and unplugged.
2 Let the appliance cool down completely on a heat-resistant surface.
3 Clean the appliance with a damp cloth.
Storage
.
Never wind the mains cord round the appliance.
1 Make sure the appliance is switched off and unplugged.
2 Let the appliance cool down on a heat-resistant surface before
storing it.
3 Use the closing lock (not available on HP4647/07) to lock the
straightening plates together before storing the appliance.
Environment
.
◗
Do not throw the appliance away with the normal household waste
at the end of its life, but hand it in at an official collection point for
recycling. By doing this you will help to preserve the environment
(fig. 5).
Guarantee & service
.
If you need information or if you have a problem, please visit the Philips
website at www.philips.com or contact the Philips Customer Care Centre
in your country (you will find its phone number in the worldwide guarantee
leaflet). If there is no Customer Care Centre in your country, turn to your
local Philips dealer or contact the Service Department of Philips Domestic
Appliances and Personal Care BV.
HP4648/39 ProCeramic
HP4648/27 ProCeramic Breeze
HP4648/07 ProCeramic
HP4647/07 ProCeramic Jade XL
www.philips.com
Troubleshooting
.
If problems should arise with your straightener and you are unable to solve
them by means of the troubleshooting guide below, please contact the
nearest Philips service centre or the Philips Customer Care Centre in your
country.
Problem
◗
The appliance does not work at all.
1 Perhaps there is a power failure or the socket is not live. Check if the
power supply is working. If it is, check whether the socket is live by
plugging in another appliance.
2 Check if the mains cord of the appliance is damaged. If the mains cord
is damaged, it must be replaced by Philips, a service centre authorised
by Philips or similarly qualified persons in order to avoid a hazard.
1
2
u
4222 002 61932
3 4 5