Panasonic CQ-C5100N Operating Instructions Manual page 21

E
Troubleshooting
N
G
L
I
S
■
H RDS
39
Problem
PS does not appear
A PS code cannot be received for the reason of bad receiving conditions, etc.
even if an RDS station
aA PS code appears if it is received. Wait for a while until conditions
is tuned into. ("NONE"
change.
appears.)
When the station changed between programs, the unit could not receive the
Receiving programs
PTY code.
differs from PTY that
aAn appropriate program is searched for and tuned into after receiving a
was already set up.
corresponding PTY code. Therefore, wait for a while.
Any specified PTY programs cannot be received. There is no desired program
"NONE" appears
being broadcast in your area.
when selecting PTY.
aSelect another PTY, or wait until a desired program starts.
The unit received a station that broadcasting time that is not appropriate for
The clock (CT) does
you, or the unit is receiving a station that does not broadcast time.
not indicate accurate
aReceive a station that broadcasting time that is appropriate for your
time.
area, or adjust CT manually.
There is little difference in receiving conditions between the current station
An AF station cannot
and AF stations. Update of AF list ended in failure.
be received even if
aWait until AF list is successfully updated. For unstable reception, tune
EON is set to ON.
into a stable station by hand.
■
CD
Problem
The disc is inserted upside down.
aInsert a disc correctly.
No playback or disc
ejected
There is a flaw or foreign objects on the disc.
aRemove the foreign objects, or use a flawless disc.
Sound skipping or There is a flaw or foreign objects on the disc.
noise aRemove the foreign objects, or use a flawless disc.
The unit is not sufficiently secured.
aSecure the unit to the console box with the rear support strap, etc.
Sound skipping due to
vibration
The unit is tilted at over 30˚ in the front-to-end direction.
aMake the angle 30˚ or less.
Something such as a peeled label obstructs the disc coming out.
aPress and hold the [OPEN] button for more than 5 seconds when the front
panel is open (disc forced ejection). In case that the disc forced ejection
does not work, consult the dealer.
Disc unejectable
The microcontroller in the unit operates abnormally due to noise or other fac-
tors.
aPress the reset switch. If there is no reset switch, unplug the power cord
and plug it again. In case the unit is still out of order, consult the dealer.
40
CQ-C5400/C5300/C5100N
(continued)
Possible cause a Possible solution
Possible cause Possible solution
a
■
MP3/WMA (Only for CQ-C5400/C5300N)
Problem
The disc has unplayable formatted data.
aRefer to the description about MP3/WMA for playable sound data except
No playback or disc
CD-DA (i.e. music CD).
ejected
The unit plays back the first track of a MIX mode CD.
aSkip the first track.
The playability of some CD-R/RWs may depend on the combination of media,
The CD-R/RWs that are
recording software and recorder to be used even if these CD-R/RWs are
playable on other
playable on other devices such as a PC.
devices are not
aMake CD-R/RWs in different combination of media, recording software
playable on this unit.
and recorder after referring to the description about MP3/WMA.
There is a flaw or foreign objects on the disc.
Sound skipping or
aRemove the foreign objects, or use a flawless disc. For MP3/WMA, refer
noise
to the description about MP3/WMA.
Note:
¡Refer to "Notes on MP3/WMA". (a Page 22)
Possible cause a Possible solution
CQ-C5400/C5300/C5100N
E
N
G
L
I
S
H
40 1
41