Table of Contents
Advertisement
E
General
N
G
L
I
[MUTE] (Mute/attenuation)
S
H
[SQ] (Sound Quality)
indicator
5
1
1
2
2
Level Meter
[VOLUME]
Remote control sensor
(a
Page 5)
[SOURCE] (PWR: Power)
Power
Turn your car's ignition key to the ACC or ON position.
ON:
Press [SOURCE] (PWR).
OFF: Press and hold [SOURCE] (PWR) until you hear
a beep (about 1 second), then release it.
Note:
¡ When the ignition switch is turned ON, the panel is open
to secure their former positions.
¡ If the security function is set to ON, the security mes-
sage is shown with a warning alarm. (Default: S-LED
ON)
(a
Page 34 about Security Function setting)
ACC Selection
If your car has the ACC position on the ignition
switch, set the ACC selection to ON. (Default: ACC
OFF)
(a
Page 34)
ACC ON
is attached to the functional descriptions
under the ACC selection ON condition.
Demonstration Message
When the power is switched on for the first time, a
demonstration message appears on the display.
Press [DISP] to change to regular mode.
Scrolling....
Note:
¡To display the message again, press and hold
[SOURCE] (PWR) for more than 4 seconds
when turning power on.
ACC ON
6
CQ-C5400/C5300/C5100N
CQ-C5400N
CQ-C5400N
BAND
3
3
4
4
5
5
6
6
Spectrum analyzer
Source
Press [SOURCE] to change the source.
3CQ-C5400/C5300N
Radio
(a
Page 10)
CD Player
(a
Page 19)
OR
MP3/WMA Player
(When a MP3/WMA data disc is
in the player.
CD Changer
(When an optional CD changer is
connected.
AUX (only for CQ-C5400N)
(a
Installation instructions)
3CQ-C5100N
Radio
(a
Page 10)
CD Player
(a
Page 19)
CD Changer
(When an optional CD changer is
connected.
Volume
[DISP] (Display)
Down
Note:
¡ The volume level can be set independently for each
source. (For radio, one volume setting for AM
(LW/MW), one volume setting for all FMs)
Mute/Attenuation
ON : Press [MUTE].
OFF : Press [MUTE] again.
You can select mute or attenuation when [MUTE] is
pressed.
(a
Page 32)
Rear Speakers as Sub-Woofers
(Super Bass Control Sub-Woofer/SBC-SW)
You can utilize the rear speaker connected to the built-in
amplifier as Sub-Woofers that output only bass.
(Default: OFF)
Press and hold [MUTE] (SBC-SW) for more than 2 sec-
onds to switch SBC-SW on and off.
Note:
Page 20)
a
¡ When ON has been selected, the settings resulting from
the adjustments performed at the subwoofer level and
subwoofer low pass filter settings are reflected in the
output.
(a
a
Page 24)
¡ Depending on the speakers used and the type of music
played, it may not be possible to achieve a satisfactory
effect.
a
Page 24)
SQ (Sound Quality)
SQ is a function that can call up various sound types at the
touch of button in accordance with your listening music
type. For SQ7, you can also make fine adjustments for SQ
presetting, P2-P6, according to your taste.
Up
Default: 18
Setting Range: 0 to 40
Press [SQ] to select a sound types as follows.
Page 28)
Press [DISP] to return to the regular mode.
Note:
¡ After pressing [SQ] on the main unit, you can also
select a sound type by pressing the preset buttons [1]-
[6].
¡ Setting of SQ, bass/treble and volume are influenced
one another. If the influence mentioned above causes
distortion to the audio signal, readjust bass/treble or
volume.
(a
Page 26)
lights. (except SQ-FLAT)
Preset number
(Default)
(Flat frequency response does not
emphasize.)
(Sharp and dynamic sound.
Powerful deep bass and turgescent
treble.)
(Prevention of excessive equalizing
and capability to cover wide variety
of music. Listener-friendly and crisp
sound.)
(Highlighted vocals that are apt to
be overwhelmed by instrumental
sound.)
(Sound with emphasis on sharpness
of high-hat and echo of saxophone.
Jazz-specific deep sound.)
(Reproduction of realism being in a
club.)
(a
Page 26)
CQ-C5400/C5300/C5100N
E
N
G
L
I
S
H
6
1
7
Hide quick links:
Advertisement
Table of Contents
